sauder.com Sit and surf. Computer Desk Palladia Collection | Model 412116 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-28 Français pg 29-32 Español pg 33-36 Lot # 364789 08/28/14 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3-4 No. 2 Phillips Screwdriver Tip Shown Actual Size 5-6 7-28 Hammer Français 29-32 Español 33-36 Safety 37-38 Warranty Page 2 Not actual size Skip the power trip. This time. 39 412116 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. HH EXTENSION RAIL - 2 II EXTENSION SLIDE - 2 JJ FILE GLIDE - 2 KK FILE ROD - 2 40CA CABINET RIGHT - 2 40CB CABINET LEFT - 2 40CC DRAWER RIGHT - 2 40CD DRAWER LEFT - 2 35AW CABINET RIGHT - 1 35AX CABINET LEFT - 1 35AY DRAWER RIGHT - 1 35AZ DRAWER LEFT - 1 TT2 XX HIDDEN CAM - 16 BRACKET - 3 BBB LARGE DRAWER FRONT BRACKET - 2 www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Scan this QR code or go to this address: http://qr.sauder.com/?ID=1584 to watch a video on how to assemble your unit. Push sixteen HIDDEN CAMS (TT2) into the ENDS (A, B, and C), UPRIGHTS (D, E, and F), and BOTTOM (H). Then, insert the metal end of a CAM DOWEL (UU2) into each HIDDEN CAM.
Step 2 å Separate the EXTENSION SLIDES (II) from the EXTENSION RAILS (HH) as shown in the upper diagram below. Be prepared, the parts are greasy. å Fasten two EXTENSION RAILS (HH) to the SMALL RIGHT END (C) and SMALL UPRIGHT (E). Use four GOLD 5/16" FLAT HEAD SCREWS (QQQ). å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the innercartridge of the EXTENSION RAIL out to find the other hole that lines up with the hole in the END.
Step 3 å Fasten the CABINET RIGHTS (40CA) and CABINET LEFTS (40CB) to the SMALL RIGHT END (C) and SMALL UPRIGHT (E). Use eight GOLD 5/16" FLAT HEAD SCREWS (QQQ) through holes #1 and #3. QQQ GOLD 5/16" FLAT HEAD SCREW (8 used in this step) Roller end 1 2 3 4 1 Finished edge 2 3 4 4 3 C 2 4 1 3 2 1 E Roller end Finished edge www.sauder.
Step 4 å Fasten the CABINET RIGHT (35AW) and CABINET LEFT (35AX) to the UPRIGHTS (D and F). Use four GOLD 5/16" FLAT HEAD SCREWS (QQQ). QQQ GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Roller end S HI urfa DD ce EN wi CA th M S These holes must be here. Roller end S HI urfa DD ce EN wi CA th M S D Page 10 F 412116 www.sauder.
Step 5 å Fasten fifteen ANGLE BRACKETS (VV) to the ENDS (A and B) and LARGE UPRIGHT (D). Use fifteen BLACK 9/16" LARGE HEAD SCREWS (NNN). NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edges of the ENDS and UPRIGHT. å Fasten the END MOLDINGS (AA) and UPPER PLINTHS (CC) to the ENDS (A and B) and LARGE UPRIGHT (D). Use fifteen BLACK 9/16" LARGE HEAD SCREWS (NNN). These edges should be even.
Step 6 å Fasten the HALF DISKS (GG) to the LOWER PLINTHS (DD). Use three BROWN 1" FLAT HEAD SCREWS (HHH). å Fasten three BRACKETS (XX) to the LEFT END (B) and LEFT UPRIGHT (F). Use three BLACK 9/16" LARGE HEAD SCREWS (NNN). å Fasten a LOWER PLINTH (DD) to the LEFT END (B). Use two BLACK 9/16" LARGE HEAD SCREWS (NNN). The larger hole should be facing up. GG GG DD GG DD DD Be sure the END MOLDING is centered on the HALF DISK (GG).
Step 7 å Fasten the ENDS (A and B) to the TOP (G). Tighten four HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. A AA B AA G ce les fa o ur h S ith w Rounded edge Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: www.sauder.
Step 8 å Fasten the SMALL RIGHT END (C) and SMALL UPRIGHT (E) to the TOP (G). Tighten four HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees Finished edge C E G Page 14 412116 www.sauder.
Step 9 å Fasten the MODESTY PANEL (I) to the LARGE UPRIGHT (D) and LEFT UPRIGHT (F). Use four BLACK 1-7/8" FLAT HEAD SCREWS (DDD). D Finished edge AA ith e w AMS c a f Sur DEN C HID I F out h t i ew S fac CAM r u S DEN HID Finished edge DDD BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) www.sauder.
Step 10 å Fasten the UPRIGHTS (D and F) to the TOP (G). Tighten four HIDDEN CAMS. å Fasten the LEFT UPRIGHT (F) to the LOWER PLINTH (DD). Use a BLACK 9/16" LARGE HEAD SCREW (NNN) through the BRACKET and into the PLINTH. Maximum 210 degrees Arrow Minimum 190 degrees NNN BLACK 9/16" LARGE HEAD SCREW (1 used in this step) D I F AA DD G Finished edge Page 16 412116 www.sauder.
Step 11 å Fasten the BOTTOM (H) to the RIGHT END (A) and LARGE UPRIGHT (D). Tighten four HIDDEN CAMS. å Fasten the BOTTOM (H) to the SMALL RIGHT END (C) and SMALL UPRIGHT (E). Use four BLACK 1-7/8" FLAT HEAD SCREWS (DDD). å Fasten four METAL BRACKETS (WW) to the BRACE (J). Use four BLACK 9/16" LARGE HEAD SCREWS (NNN). å NOTE: Be sure the BRACKETS are even with the edges of the BRACE. å Fasten the BRACE (J) to the RIGHT END (A), LARGE UPRIGHT (D), and BOTTOM (H).
Step 12 å å Fasten the LOWER PLINTHS (DD) to the BRACE (J). Use four BLACK 1-1/4" FLAT HEAD SCREWS (FFF). Fasten the BASE (K) and BOTTOM MOLDING (BB) to the BRACE (J). Use four BROWN 1" FLAT HEAD SCREWS (HHH). Don't worry. It isn't Rome. This can be built in a day. FFF BLACK 1-1/4" FLAT HEAD SCREW (4 used for the LOWER PLINTHS) HHH BROWN 1" FLAT HEAD SCREW (4 used for the BOTTOM MOLDING) Flat end DD BB J K DD Be sure the END MOLDING is centered against the HALF DISK on the LOWER PLINTH (DD).
Step 13 å Carefully turn your unit over onto its front edges. Lay the BACKS (EE and FF) over your unit. å Make equal margins along the bottom and both side edges of the BACKS (EE and FF). Push on opposite corners of your unit if needed to make it "square". å Fasten the BACK (EE and FF) to your unit using the NAILS (RRR). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse.
Step 14 å Fasten the KEYBOARD SIDES (N) to the KEYBOARD SHELF (O). Use four BROWN 1-1/2" FLAT HEAD SCREWS (EEE). å Fasten the KEYBOARD SIDES (N) to the KEYBOARD BACK (M). Use two BROWN 1-1/2" FLAT HEAD SCREWS (EEE). å Fasten the KEYBOARD BACK (M) to the KEYBOARD SHELF (O). Use two SMALL BLACK 1-1/4" FLAT HEAD SCREWS (GGG). This surface should be the same finish as this surface.
Step 15 å Fasten two HINGES (YY) to the KEYBOARD FRONT (L). Use four SILVER 5/8" FLAT HEAD SCREWS (MMM). å Fasten the HINGES (YY) to the KEYBOARD SHELF (O). Use two SILVER 9/16" LARGE HEAD SCREWS (OOO). O L YY OOO MMM SILVER 9/16" LARGE HEAD SCREW (2 used in this step) SILVER 5/8" FLAT HEAD SCREW (4 used in this step) www.sauder.
Step 16 å Fasten the DRAWER RIGHT (35AY) and DRAWER LEFT (35AZ) to the KEYBOARD SHELF (O). Use four SMALL BROWN 1" FLAT HEAD SCREWS (III). å Fasten two KNOBS (ZZ) to the KEYBOARD FRONT (L). Use two BLACK 7/8" MACHINE SCREWS (LLL). Roller end LLL BLACK 7/8" MACHINE SCREW (2 used for the KNOBS) O L Roller end ZZ III SMALL BROWN 1" FLAT HEAD SCREW (4 used for the DRAWER SLIDES) Page 22 412116 www.sauder.
Step 17 VIEW THE T-SLOT BOX VIDEO å Pull the DRAWER FRONT BRACKETS (AAA and BBB) apart and slide them into the grooves in the DRAWER SIDES (D212, D213, D260, and D263). å Fasten the DRAWER FRONTS (P and T) to the DRAWER FRONT BRACKETS (AAA and BBB). Use eight BLACK 9/16" LARGE HEAD SCREWS (NNN). å NNN Repeat this step for the small drawer parts W, D34, and D35. Use the SMALL DRAWER FRONT BRACKETS (CCC) and two BLACK 9/16" LARGE HEAD SCREWS (NNN).
Step 18 VIEW THE T-SLOT BOX VIDEO å Slide the DRAWER BOTTOMS (D707) into the grooves in the DRAWER FRONTS (P and T) and DRAWER SIDES (D212, D213, D260, and D263). å Fasten the DRAWER BACKS (D78 and D86) to the DRAWER SIDES (D212, D213, D260, and D263). Use eight BLACK 1-9/16" FLAT HEAD SCREWS (30S). å NOTE: Be sure the DRAWER BOTTOMS (D707) insert into the grooves the DRAWER BACKS (D78 and D86). å Repeat this step for the small drawer. Use the SMALL DRAWER BOTTOM (D716) and SMALL DRAWER BACK (D74).
Step 19 å Fasten the EXTENSION SLIDES (II) to the LARGE DRAWER SIDES (D260 and D263). Use four GOLD 5/16" FLAT HEAD SCREWS (QQQ) through holes #1 and #3. Open end 1 II 3 2 D263 D260 Open end 1 II 3 2 QQQ GOLD 5/16" FLAT HEAD SCREW (4 used in this step) www.sauder.
Step 20 å Fasten the DRAWER RIGHT (40CC) and DRAWER LEFT (40CD) to the DRAWER SIDES (D212 and D213). Use four GOLD 5/16" FLAT HEAD SCREWS (QQQ) through the holes #1 and #4. å Repeat this step for the small drawer. Use holes #2 and #4 in the DRAWER SLIDES. Roller end 1 2 4 3 D213 Roller end D212 1 2 4 3 (4 screws per drawer) QQQ GOLD 5/16" FLAT HEAD SCREW (8 used in this step) Page 26 412116 www.sauder.
Step 21 å Fasten a KNOB (ZZ) to the LARGE DRAWER FRONT (T). Use a SILVER 1/2" MACHINE SCREW (PPP). JJJ å Repeat this step for the other drawers. Use a GOLD 1" MACHINE SCREW (JJJ) for the small drawer. å Push a FILE GLIDE (JJ) onto the LARGE RIGHT DRAWER SIDE (D260). å Slide the FILE RODS (KK) into the FILE GLIDE (JJ) on the LARGE RIGHT DRAWER SIDE. å Slide another FILE GLIDE (JJ) onto the other end of the FILE RODS (KK), then press this FILE GLIDE over the LARGE LEFT DRAWER SIDE (D263).
Step 22 å å Carefully stand your unit upright. å To insert the other drawers into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit. Lift the front of the drawer up and slide it into the unit. Repeat this step for the KEYBOARD SHELF. å To make adjustments to the drawers, loosen the SCREWS in the DRAWER FRONT BRACKETS, make needed adjustments, and tighten the SCREWS.
Modèle 412116 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 5 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Fixer quinze CONSOLES À ÉQUERRE (VV) aux EXTRÉMITÉS (A et B) et au GRAND MONTANT (D). Utiliser quinze VIS NOIRES TÊTE LARGE 14 mm (NNN). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer seize EXCENTRIQUES ESCAMOTABLES (TT2) dans les EXTRÉMITÉS (A, B et C), les MONTANTS (D, E et F) et le DESSOUS (H).
ÉTAPE 9 ÉTAPE 13 Fixer le VOILE DE FOND (I) au GRAND MONTANT (D) et au MONTANT GAUCHE (F). Utiliser quatre VIS NOIRES TÊTE PLATE 48 mm (DDD). Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. ÉTAPE 10 Veiller à avoir des marges égales le long des chants inférieur et latéraux des ARRIÈRES (EE et FF). Si besoin est, enfoncer sur les coins opposés de l'élément pour s'assurer d'être « d'équerre ».
ÉTAPE 16 ÉTAPE 20 Fixer le TIROIR DROIT (35AY) et le TIROIR |GAUCHE (35AZ) à la TABLETTE DE CLAVIER (O). Utiliser quatre PETITES VIS MARRON TÊTE PLATE 25 mm (III). Fixer le TIROIR DROIT (40CC) et le TIROIR GAUCHE (40CD) aux CÔTÉS DE TIROIR (D212 et D213). Utiliser quatre VIS DORÉES TÊTE PLATE 8 mm (QQQ) à travers les trous nº 1 et nº 4. Fixer deux BOUTONS (ZZ) au DEVANT DE TABLETTE DE TIROIR (L). Utiliser deux VIS NOIRE À MÉTAUX 22 mm (LLL). Répéter cette étape pour le petit tiroir.
Modelo 412116 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 5 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Fije quince SOPORTES ANGULARES (VV) a los EXTREMOS (A y B) y al PARAL GRANDE (D). Utilice quince TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (NNN). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje dieciséis EXCÉNTRICOS ESCONDIDOS (TT2) dentro de los EXTREMOS (A, B y C), de los PARALES (D, E y F) y del FONDO (H).
PASO 9 PASO 13 Fije el VELO DE FONDO (I) al PARAL GRANDE (D) y al EXTREMO IZQUIERDO (F). Utilice cuatro TORNILLOS NEGROS DE CABEZA PERDIDA de 48 mm (DDD). Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. PASO 10 Fije los PARALES (D y F) al PANEL SUPERIOR (G). Apriete cuatro EXCÉNTRICOS ESCONDIDOS. Fije el PARAL IZQUIERDO (F) a la BASE INFERIOR (DD). Pase un TORNILLO NEGRO DE CABEZA GRANDE de 14 mm (NNN) a través del SOPORTE y dentro de la BASE.
PASO 16 PASO 20 Fije la CAJÓN DERECHO (35AY) y la CAJÓN IZQUIERDO (35AZ) al ESTANTE DE TECLADO (O). Utilice cuatro TORNILLOS PEQUEÑOS MARRONES DE CABEZA PERDIDA de 25 mm (III). Fije la CAJÓN DERECHO (40CC) y la CAJÓN IZQUIERDO (40CD) a los LADOS DE CAJÓN (D212 y D213). Utilice cuatro tornillos DORADOS de cabeza PERDIDA de 8 mm (QQQ) a través de los agujeros No. 1 y No. 4. Fije dos TIRADORES (ZZ) a la CARA DE ESTANTE DE TECLADO (L). Utilice dos TORNILLOS NEGRO PARA METAL de 22 mm (LLL).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves and drawers. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves and drawers can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes y cajones sobrecargados • Riesgo de lesiones. • Cargar el producto de manera inadecuada • El mobiliario inestable puede volcarse. puede causar la inestabilidad. • Estantes y cajones sobrecargados pueden romperse.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
