sauder.com Designed for distractions. TV Stand Model 413010 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-18 Français pg 19-21 Español pg 22-24 Lot # 532853 08/30/19 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-18 Hammer Français 19-21 Español 22-24 Safety 25-26 Warranty Not actual size Skip the power trip. This time. 27 ! WARNING Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or death.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 5E FOOT CAP - 1 8F CAM SCREW - 10 6E FOOT BRACKET - 1 27G ANGLE BRACKET - 2 22E TACK GLIDE -4 14H HINGE - 4 6K 1F 2F HIDDEN CAM - 24 PULL - 2 1L CAM DOWEL - 14 WARNING LABEL - 1 WARNING For use with televisions weighing 50 lbs. (22.6 kg) or less. Use with heavier televisions may result in instability causing tip over resulting in death or serious injury.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push fourteen HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHTS (C and D), and BOTTOM (F). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step.
Step 2 å Push ten HIDDEN CAMS (1F) into the long edges of the ENDS (A and B) and TOP (E3). Arrow Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. E3 (10 used) Arrow 1F B A Arrow 1F Page 6 413010 www.sauder.
Step 3 å Turn ten CAM SCREWS (8F) into the FRONT LEGS (L and M) and STOP MOLDING (O2). (10 used) O2 8F L M 8F www.sauder.
Step 4 å Fasten the LEFT END (B) to the LEFT FRONT LEG (M). Tighten three HIDDEN CAMS. å Fasten a REAR LEG (N) to the LEFT END (B). Use three BLACK 1-7/8" FLAT HEAD SCREWS (2S). 2S BLACK 1-7/8" FLAT HEAD SCREW (3 used in this step) N Edge with CAM DOWELS Angled edge B Sur HIDface w DEN ith CA MS The LEGS will overhang this edge. These surfaces should be even. M 1 Angled edge 2 Page 8 413010 www.sauder.
Step 5 å Fasten the RIGHT END (A) to the RIGHT FRONT LEG (L). Tighten three HIDDEN CAMS. å Fasten the REAR LEG (N) to the RIGHT END (A). Use three BLACK 1-7/8" FLAT HEAD SCREWS (2S). Just think. The sooner you do this, the sooner you do something else. 2S BLACK 1-7/8" FLAT HEAD SCREW (3 used in this step) Angled edge N The LEGS will overhang this edge. Sur HIDface w DEN ith CA MS A Edge with CAM DOWELS Angled edge L These surfaces should be even. www.sauder.
Step 6 å Fasten the UPRIGHTS (C and D) to the TOP (E3). Tighten four HIDDEN CAMS. å Fasten the STOP MOLDING (O2) to the TOP (E3). Tighten four HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Curved edge O2 e fac Sur s ole h h wit Finished edge E3 e fac Sur withDEN HID S M CA Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate.
Step 7 å Fasten the BOTTOM (F) to the UPRIGHTS (C and D). Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S). å Slide the BOTTOM MOLDING* (P) onto the notched edge of the BOTTOM (F). å *U.S. Patent No. 5,499,886 Notched edge e fac Sur withDEN HID S M CA C D F P 2S BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) Slide the BOTTOM MOLDING (P) onto the notched edge. The groove is closer to this edge. www.sauder.
Step 8 å Fasten the ENDS (A and B) to the TOP (E3), BOTTOM (F) and STOP MOLDING (O2). Tighten ten HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees Sur withface HID CA DEN MS O2 A E3 F B Sur HIDface w DEN itho CA ut MS Page 12 413010 www.sauder.
Step 9 å Fasten two ANGLE BRACKETS (27G) to the VALANCE (Q3). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the edges of the ANGLE BRACKETS are even with the long edge of the VALANCE. å Fasten the VALANCE (Q3) to the TOP (E3). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). å With a hammer, carefully tap four TACK GLIDES (22E) into the bottom edges of the LEGS (L, M, and N). Don't worry. It isn't Rome. This can be built in a day.
Step 10 å Carefully turn your unit over onto its front edges. Unfold the BACK (G) and lay it over your unit. å Make equal margins along the short edges and along the long edges of the BACK (G). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (G) to your unit using the NAILS (1N). å NOTE: Perforations have been provided for access through the BACK. Carefully cut out the holes needed. Caution Do not stand the unit upright without the BACK fastened.
Step 11 å Fasten the FOOT BRACKET (6E) to the BOTTOM (F). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). å Slide two FOOT MOLDINGS (R) onto the FOOT BRACKET (6E). Then, fasten the FOOT MOLDINGS (R) to the FOOT BRACKET (6E). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). å Firmly push the FOOT CAP (5E) onto the FOOT MOLDINGS (R). 1S BLACK 9/16" LARGE HEAD SCREW (5 used in this step) 6E R R 5E Completed leg support F R 6E R 5E www.sauder.
Step 12 å å å Fasten the HINGES (14H) to the DOORS (H and I). Use eight BLACK 1/2" FLAT HEAD SCREWS (11S). å Fasten the RIGHT DOOR (H) to the RIGHT END (A). Use the screws in the HINGES. You should start each SCREW a few turns before completely tightening any of them. å å Fasten a PULL (6K) to the RIGHT DOOR (H). Use two BLACK 7/8" MACHINE SCREWS (37S). å å Repeat this step for the other door. Carefully stand your unit upright.
Step 13 å Refer to the enlarged diagram to identify the parts on the HINGES. å The DOORS may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal) turn the adjusting screw in or out. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws. Move the DOORS up or down to the desired location. Tighten the screws after making adjustments.
Step 14 å Apply the WARNING LABEL (1L) to the TOP (E3). You should be able to read the label when the TV is removed from the unit. When the TV is in place, it should hide the label. Peel off the backing and apply the label as shown in the diagram. å å NOTE: This is a permanent label intended to last for the life of the product. Once applied, do not try to remove it. å å NOTE: Please read the back pages of the instruction booklet for important safety information.
Modèle 413010 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
AVERTISSEMENT ÉTAPE 4 L'utilisation d'un téléviseur trop lourd ou trop gros est dangereuse. Un téléviseur trop lourd créera un risque de basculement pouvant provoquer de graves blessures ou la mort. Un téléviseur trop gros pour l'espace disponible risque d'être accidentellement poussé ou de tomber du mobilier ou d'être sujet à basculer. Fixer l'EXTRÉMITÉ GAUCHE (B) au PIED AVANT GAUCHE (M). Serrer trois EXCENTRIQUES ESCAMOTABLES. Fixer un PIED ARRIÈRE (N) à l'EXTRÉMITÉ GAUCHE (B).
ÉTAPE 9 ÉTAPE 12 (SUITE) Fixer deux CONSOLES À ÉQUERRE (27G) au LAMBREQUIN (Q3). Utiliser deux VIS TÊTE LARGE 14 mm NOIRES (1S). Fixer la PORTE DROITE (H) à l'EXTRÉMITÉ DROITE (A). Utiliser les vis fournies avec les CHARNIÈRES. Il est préférable de donner quelques tours de tournevis à chaque VIS avant de les serrer toutes à bloc. REMARQUE : S'assurer que les chants des CONSOLES À ÉQUERRE sont à fleur du long chant du LAMBREQUIN. Fixer le LAMBREQUIN (Q3) au DESSUS (E3).
Modelo 413010 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
ADVERTENCIA PASO 4 El uso de un televisor demasiado pesado o grande es peligroso. Un televisor demasiado pesado generará riesgo de caída, lo cual podría causar lesiones graves o muerte. Un televisor demasiado grande para el espacio disponible puede ser empujado o golpeado por accidente, causando que éste se salga del mueble o se caiga. Fije el EXTREMO IZQUIERDO (B) a la PATA IZQUIERDA DELANTERA (M). Apriete tres EXCÉNTRICOS ESCONDIDOS. • Verifique el tamaño y peso del televisor.
PASO 9 PASO 12 (CONTINUACIÓN) Fije dos SOPORTES ANGULARES (27G) a la CORNISA (Q3). Utilice dos TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). Fije la PUERTA DERECHA (H) al EXTREMO DERECHO (A). Utilice los tornillos provistos de las BISAGRAS. Debe apretar cada TORNILLO unas vueltas antes de apretar cualquier tornillo firmemente. NOTA: Asegúrese que los bordes de los SOPORTES ANGULARES estén nivelados con el borde largo de la CORNISA. Fije la CORNISA (Q3) al PANEL SUPERIOR (E3).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following safety information. Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or toys placed on the furnishing may encourage a child to climb on the furnishing and as a result may tip over onto the child.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Lea cuidadosamente la siguiente información de seguridad. Pueden suceder lesiones graves o la muerte cuando los niños se suben en los muebles de equipo de audio y/o video. Un control remoto o juguetes colocados en el mueble pueden alentar a un niño a subirse en el mueble y como resultado puede derribarse sobre el niño.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
