sauder.com For all your newfangled gadgetry. Desk with Hutch 413084 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-22 Français pg 23-25 Español pg 26-28 Lot # 373220 05/22/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-22 Hammer Français 23-25 Español 26-28 Safety 29-30 Warranty Page 2 Not actual size Skip the power trip. This time. 31 413084 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push nine HIDDEN CAMS (AA2) into the ENDS (A and B), UPRIGHTS (E and F), and DRAWER SIDES (S and T). Then, insert the metal end of a CAM DOWEL (BB2) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step.
Step 2 å Fasten the CABINET RIGHT (35AW) to the RIGHT END (A) and the CABINET LEFT (35AX) to the UPRIGHT (E). Use four GOLD 5/16" FLAT HEAD SCREWS (PP). PP GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Roller end Finished edge Roller end S HI urfa DD ce EN wi CA th M S A S HI urfa DD ce EN wi CA th M S E Finished edge Page 6 413084 www.sauder.
Step 3 å Fasten the BRACE (U) to the UPPER SHELF (K2). Use two BLACK 1-15/16" FLAT HEAD SCREWS (113S). Finished edge Finished edge h wit e s c rfa ole Su re h mo U K2 If the BRACE (U) has an unfinished surface, it should be positioned toward the floor. 113S BLACK 1-15/16" FLAT HEAD SCREW (2 used in this step) www.sauder.
Step 4 å Fasten the UPPER ENDS (C2 and D2) to the UPPER SHELF (K2) and BRACE (U). Use six BLACK 1-15/16" FLAT HEAD SCREWS (113S). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. 113S BLACK 1-15/16" FLAT HEAD SCREW (6 used in this step) Long finished edge Short finished edge C2 K2 Short finished edge U D2 Long finished edge Page 8 413084 www.sauder.
Step 5 å Fasten the UPPER UPRIGHT (F) to the UPPER SHELF (K2). Tighten a HIDDEN CAM. K2 Finished edge F Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: www.sauder.
Step 6 å Fasten the TOP (G2) to the UPPER ENDS (C2 and D2) and UPPER UPRIGHT (F). Use six BLACK 1-15/16" FLAT HEAD SCREWS (113S). Long finished edge C2 F G2 ith e ws c rfa ole Su re h mo D2 113S BLACK 1-15/16" FLAT HEAD SCREW (6 used in this step) Page 10 413084 www.sauder.
Step 7 å Fasten the RIGHT END (A) to the TOP (G2). Tighten two HIDDEN CAMS. å Fasten the MODESTY PANEL (I) to the RIGHT END (A). Use two BLACK 1-7/8" FLAT HEAD SCREWS (LL). Maximum 210 degrees Arrow Minimum 190 degrees LL BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) Finished edge A Sur fac ew ith HID DEN CA MS G2 I Notch If the MODESY PANEL (I) has an unfinished surface, it should be positioned toward the floor. www.sauder.
Step 8 å Fasten the UPRIGHT (E) to the TOP (G2). Tighten two HIDDEN CAMS. å Fasten the UPRIGHT (E) to the MODESTY PANEL (I). Use two BLACK 1-7/8" FLAT HEAD SCREWS (LL). å Fasten the BOTTOM (H) and SHELF (J) to the UPRIGHT (E). Use four BLACK 1-7/8" FLAT HEAD SCREWS (LL).
Step 9 å Fasten the LEFT END (B) to the TOP (G2). Tighten two HIDDEN CAMS. å Fasten the LEFT END (B) to the BOTTOM (H) and SHELF (J). Use four BLACK 1-7/8" FLAT HEAD SCREWS (LL). å Maximum 210 degrees Arrow Minimum 190 degrees Push the DOOR STOP (DD) into the hole in the UPRIGHT (E). DD Finished edge G2 J E B Sur HIDface w DEN itho CA ut MS H LL BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) www.sauder.
Step 10 å Carefully turn your unit over onto its front edges. Unfold the BACK (P) and lay it over your unit. å Make equal margins along all four edges of the BACK (P). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (P) to your unit using the NAILS (QQ). å Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Next, fasten the SMALL BACK (O) to your unit using the remaining NAILS (QQ). The SMALL BACK will overlap the BACK (P).
Step 11 å Fasten the HINGES (EE) to the DOOR (Q). Use four BLACK 1/2" FLAT HEAD SCREWS (OO). OO BLACK 1/2" FLAT HEAD SCREW (4 used in this step) Q EE www.sauder.
Step 12 å å Carefully stand your unit upright. å Fasten the DOOR (Q) to the LEFT END (B). Use the screws in the HINGES. See the next step for door adjustments. å Fasten a PULL (FF) to the DOOR (Q). Use two SILVER 7/8" MACHINE SCREWS (NN). Pro Tip: Lift with your legs. And, you know, your arms. Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the diagram. If it isn't, loosen the mounting screw to slide it against the stops.
Step 13 å å Refer to the enlarged diagram to identify the parts on the HINGES. å å DOOR ADJUSTMENTS: å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws. Move the DOORS up or down to the desired location. Tighten the screws after making adjustments. å To adjust the DOORS in or out (depth), loosen the mounting screw one turn and move the DOORS in or out, as needed. Tighten the mounting screw after making adjustments. The DOORS may need some adjustments.
Step 14 å Fasten the DRAWER SIDES (S and T) to the DRAWER BACK (L). Use two BLACK 1-7/8" FLAT HEAD SCREWS (LL). T Edge and surface with HIDDEN CAMS. L S Edge and surface with HIDDEN CAMS. LL BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) Page 18 413084 www.sauder.
Step 15 å Fasten the DRAWER SIDES (S and T) to the DRAWER BOTTOM (V). Use four BLACK 1-7/8" FLAT HEAD SCREWS (LL). å Fasten the DRAWER FRONT (R) to the DRAWER SIDES (S and T). Tighten two HIDDEN CAMS. LL T BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) V S 16" / 1-7 T This hole should be closer to the front edge. S Maximum 210 degrees Arrow R Minimum 190 degrees www.sauder.
Step 16 å Fasten the DRAWER RIGHT (35AY) and the DRAWER LEFT (35AZ) to the DRAWER BOTTOM (V). Use four BROWN 1" FLAT HEAD SCREWS (MM). å Fasten the PULL (FF) to the DRAWER FRONT (R). Use two SILVER 7/8" MACHINE SCREWS (NN). Roller end NN SILVER 7/8" MACHINE SCREW (2 used for the PULL) V Roller end FF R MM BROWN 1" FLAT HEAD SCREW (4 used for the SLIDES) Page 20 413084 www.sauder.
Step 17 å Center a SCREW COVER (GG) over the head of each visible SCREW and press firmly. å å Push a CAM COVER (HH) onto each visible HIDDEN CAM. Insert the GROMMET (CC) into the large hole in the TOP (G2). CC G2 GG (14 used) To cover screws HH (4 used) To cover HIDDEN CAMS www.sauder.
Step 18 å To insert the drawer into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit. Lift the front of the drawer up and slide it into the unit. å Push the RUBBER SLEEVES (JJ) over the METAL PINS (II). Insert the METAL PINS into the hole locations of your choice in the LEFT ENDS (B and D2) and UPRIGHTS (E and F). Set the ADJUSTABLE SHELVES (M and N) onto the METAL PINS.
413084 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 7 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Fixer l'EXTRÉMITÉ DROITE (A) au DESSUS (G2). Serrer deux EXCENTRIQUES ESCAMOTABLES. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Fixer le VOILE DE FOND (I) à l'EXTRÉMITÉ DROITE (A). Utiliser deux VIS NOIRES TÊTE PLATE 48 mm (LL). Enfoncer neuf EXCENTRIQUES ESCAMOTABLES (AA2) dans les EXTRÉMITÉS (A et B), les MONTANTS (E et F) et les CÔTÉS DE TIROIR (S et T).
ÉTAPE 11 ÉTAPE 15 Fixer les CHARNIÈRES (EE) à la PORTE (Q). Utiliser quatre VIS NOIRES TÊTE PLATE 13 mm (OO). Enfiler les CÔTÉS DE TIROIR (S et T) sur le FOND DE TIROIR (V). Utiliser quatre VIS NOIRES TÊTE PLATE 48 mm (LL). ÉTAPE 12 Relever, avec précaution, l'élément dans sa position verticale. Avant de fixer la PORTE à l’unité, s’assurer que la vis de montage se trouve contre les butées comme l’indique le schéma.
413084 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 7 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Fije el EXTREMO DERECHO (A) al PANEL SUPERIOR (G2). Apriete dos EXCÉNTRICOS ESCONDIDOS. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje nueve EXCÉNTRICOS ESCONDIDOS (AA2) dentro de los EXTREMOS (A y B), de los PARALES (E y F) y de los LADOS DE CAJÓN (S y T). A continuación, inserte el extremo de metal de un PASADOR DE EXCÉNTRICO (BB2) dentro de cada EXCÉNTRICO ESCONDIDO.
PASO 11 PASO 15 Fije las BISAGRAS (EE) a la PUERTA (Q). Utilice cuatro TORNILLOS NEGROS DE CABEZA PERDIDA de 13 mm (OO). Fije los LADOS DE CAJÓN (S y T) al FONDO DE CAJÓN (V). Utilice cuatro TORNILLOS NEGROS DE CABEZA PERDIDA de 48 mm (LL). PASO 12 Cuidadosamente ponga la unidad en posición vertical. Antes de ajustar la PUERTA en su unidad, asegúrese de que el tornillo de montaje esté contra los topes, tal como se muestra en el diagrama de la derecha.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves and drawers. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves and drawers can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes y cajones sobrecargados. • Riesgo de lesiones. • Cargar el producto de manera inadecuada • El mobiliario inestable puede volcarse. puede causar la inestabilidad. • Estantes y cajones sobrecargados pueden romperse.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
