413678 Storage Cabinet PLEASE CONTACT US BEFORE RETURNING YOUR UNIT TO THE STORE 1-800-523-3987 www.sauder.com NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. English .................... Page 1-12 Français ...............Pages 13-14 Made in the USA Archbold, OH Espanol.............
TABLE OF CONTENTS ASSEMBLY TOOLS REQUIRED Part Identification .......................3 No. 2 Phillips Screwdriver Hardware Identification .............4 Tip Shown Actual Size Assembly Steps .................... 5-12 Français .............................. 13-14 Hammer Espanol............................... 15-16 Safety ................................. 17-18 Warranty ...................................19 Page 2 www.sauder.
PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help identify similar parts. A RIGHT END 1 F ADJUSTABLE SHELF 4 B LEFT END 1 G BACK 1 C UPRIGHT 1 H DOOR 2 D TOP 1 I SKIRT 1 E BOTTOM/SHELF 2 D G E A F C F F B F H H E I 413678 www.sauder.
HARDWARE IDENTIFICATION J K HINGE - 6 SAFETY BRACKET - 1 L PULL - 2 M FELT DISC CARD - 1 N SCREW COVER - 12 O METAL PIN - 20 P RUBBER SLEEVE - 16 Q BLACK 1-7/8" FLAT HEAD SCREW - 17 R SILVER 3/4” MACHINE SCREW - 4 S BROWN 7/16" LARGE HEAD SCREW - 25 T NAIL - 36 Screws are shown actual size. You may receive extra hardware with your unit. Page 4 www.sauder.
S p te Look for this icon. It means a video assembly tip is available at: www.sauder.com/services/tips 1 Long unfinished edge D Fin ish A ed Q BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Fasten the RIGHT END (A) to the TOP (D). Use two BLACK 1-7/8" FLAT HEAD SCREWS (Q). 413678 www.sauder.
S p te 2 Long unfinished edge A Un E fini she d C Q BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) Edge with three holes. For support, place packing foam and magazines here. Fasten the BOTTOM/SHELF (E) to the RIGHT END (A). Use two BLACK 1-7/8" FLAT HEAD SCREWS (Q). Fasten the UPRIGHT (C) to the BOTTOM/SHELF (E). Use two BLACK 1-7/8" FLAT HEAD SCREWS (Q). Page 6 www.sauder.
S p te 3 Long unfinished edge A C E Un fini she d I O Q (4 used) BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) Fasten the other BOTTOM/SHELF (E) to the RIGHT END (A) and UPRIGHT (C). Use four BLACK 1-7/8" FLAT HEAD SCREWS (Q). Insert four METAL PINS (O) into the SKIRT (I). Push the METAL PINS (O) in one end of the SKIRT (I) into the holes in the RIGHT END (A). NOTE: Do now allow the SKIRT to hang freely until it is fastened to the LEFT END (B). 413678 www.sauder.
S p te 4 Long unfinished edge D E B E I Q BLACK 1-7/8" FLAT HEAD SCREW (6 used in this step) Fasten the LEFT END (B) to the TOP (D) and BOTTOM/SHELVES (E). Use six BLACK 1-7/8" FLAT HEAD SCREWS (Q). NOTE: Be sure the METAL PINS (O) in the SKIRT (I) insert into the holes in the LEFT END (B). Page 8 www.sauder.
S p te Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. 5 n U G fi ed sh ni 2” 6” 1/4” T NAIL (36 used in this step) Unfold the BACK (G) and lay it over your unit. Make equal margins along all four edges of the BACK (G). Push on opposite corners of your unit if needed to make it “square”. Fasten the BACK (G) to your unit using the NAILS (T). The NAILS should be 6" apart, 2" from the corners, and 1/4" in from the edges. 413678 www.sauder.
S p te 6 K H H K S BROWN 7/16" LARGE HEAD SCREW (12 used in this step) Fasten the HINGES (K) to the DOORS (H). Use twelve BROWN 7/16" LARGE HEAD SCREWS (S). Page 10 www.sauder.
S p te 7 M D R SILVER 3/4” MACHINE SCREW (4 used for the PULLS) B L H E S M BROWN 7/16" LARGE HEAD SCREW (12 used for the HINGES) Carefully stand your unit upright. Fasten a DOOR (H) to the LEFT END (B). Use six BROWN 7/16" LARGE HEAD SCREWS (S). Then, peel the FELT DISC from the FELT DISC CARD (M). Stick the FELT DISC on the DOOR where it comes in contact with the TOP (D) and lower BOTTOM/SHELF (E). Fasten a PULL (L) to the DOOR (H). Use two SILVER 3/4" MACHINE SCREWS (R).
S BLACK 1-7/8” FLAT HEAD SCREW (1 used into a stud in your wall) p te 8 Q J BROWN 7/16” LARGE HEAD SCREW (1 used into the top of your unit) No load S 50 lbs. F 25 lbs. F B 25 lbs. F C (12 used) N 25 lbs. A F 25 lbs. 50 lbs. O (16 used) P IMPORTANT: This unit must be positioned against a wall. Push the RUBBER SLEEVES (P) over the remaining METAL PINS (O). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B) and UPRIGHT (C).
413678 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Fixer les CHARNIÈRES (K) aux PORTES (H). Utiliser douze VIS MARRON TÊTE LARGE 11 mm (S). Fixer l'EXTRÉMITÉ DROITE (A) au DESSUS (D). Utiliser deux VIS NOIRES TÊTE PLATE 48 mm (Q). ÉTAPE 7 Relever, avec précaution, l'élément dans sa position verticale. ÉTAPE 2 Fixer la pièce DESSOUS/TABLETTE (E) à l'EXTRÉMITÉ DROITE (A). Utiliser deux VIS NOIRES TÊTE PLATE 48 mm (Q).
413678 Gabinete para almacenaje Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Fije las BISAGRAS (K) a las PUERTAS (H). Utilice doce TORNILLOS MARRONES DE CABEZA GRANDE de 11 mm (S). Fije el EXTREMO DERECHO (A) al PANEL SUPERIOR (D). Utilice dos TORNILLOS NEGROS DE CABEZA PERDIDA de 48 mm (Q). PASO 7 Cuidadosamente ponga la unidad en posición vertical. PASO 2 Fije la parte FONDO/ESTANTE (E) al EXTREMO DERECHO (A).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes sobrecargados. • Un riesgo de lesiones. • La caída de mobiliario inestable. • La rotura de cajones sobrecargados. • Nunca exceder los límites de peso indicados en las instrucciones.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear valued customer: Thank you for your purchase from the Sauder family companies. It’s our pleasure to provide you with an affordable solution that meets your furniture and storage needs. I hope you will enjoy it for years to come. I am pleased with this company’s consistent ability to amaze the customer over time. My grandfather, Erie Sauder, founded the company in 1934 and later invented and patented the first commercially successful ready-to-assemble table.