sauder.com We'll have you in stitches. Sewing/Craft Cart Model 414110 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-18 Français pg 19-21 Español pg 22-25 Lot # 533528 10/15/19 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-18 Hammer Français 19-21 Español 22-25 Safety 26 Warranty 27 Page 2 Not actual size Skip the power trip. This time. 414110 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push fourteen HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHT (C2), BOTTOM (F), MODESTY PANEL (G2), and SHELF (H2). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step.
Step 2 å Fasten the RIGHT END (A) to the TOP (D2). Tighten two HIDDEN CAMS. å Fasten the BOTTOM (F) to the RIGHT END (A). Tighten two HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. S HID urfac DEN e w CA ith MS Finished edge F A ith e w AMS c a f Sur DEN C D HI D2 Sur fac ew ith hol es Rounded edge Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened.
Step 3 å Fasten the UPRIGHT (C2) to the TOP (D2) and BOTTOM (F). Tighten four HIDDEN CAMS. å Fasten the MODESTY PANEL (G2) to the UPRIGHT (C2). Use two BLACK 1-15/16" FLAT HEAD SCREWS (113S). å Fasten two MAGNETIC CATCHES (5I) to the UPRIGHT (C2). Use two BLACK 1-1/8" PAN HEAD SCREWS (9S).
Step 4 å Fasten the LEFT END (B) to the TOP (D2) and MODESTY PANEL (G2). Tighten four HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees Sur fac ew ith HID DEN CA MS B G2 D2 Page 8 414110 www.sauder.
Step 5 å Fasten the SHELF (H2) to the LEFT END (B). Tighten two HIDDEN CAMS. å Fasten the SHELF (H2) to the UPRIGHT (C2). Use two BLACK 1-15/16" FLAT HEAD SCREWS (113S). Maximum 210 degrees Arrow Minimum 190 degrees Surface with HIDDEN CAMS H2 B C2 113S BLACK 1-15/16" FLAT HEAD SCREW (2 used in this step) www.sauder.
Step 6 å Carefully turn your unit over onto its front edges. Lay the BACK (L) over your unit. å Make equal margins along all four edges of the BACK (L). Push on opposite corners of your unit if needed to make it "square". å Fasten the BACK (L) to your unit using the NAILS (1N). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. 1N NAIL (13 used in this step) The BACK (L) should be against the bottom surface of the TOP (D2). These holes must be here.
Step 7 å Fasten two HINGES (16H) to the TOP (D2) and FLIP-UP TOP (E). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). Remember: Righty tighty. Lefty loosey. 1S BLACK 9/16" LARGE HEAD SCREW (8 used for the HINGES) 16H D2 E Sur fac ew ith hol es www.sauder.
Step 8 å Place five CASTER BRACKETS (17E) over the holes in the bottom edges of ENDS (A and B) and UPRIGHT (C2). å Firmly push two LOCKING CASTERS (2CL) into the holes as shown in the CASTER BRACKETS (17E) and ENDS (A and B). å Firmly push three CASTERS (2CN) into the remaining holes in the ENDS (A and B) and UPRIGHT (C2). (5 used) 17E 2CN A C2 B 17E 2CL The LOCKING CASTER has a lever. Page 12 414110 www.sauder.
Step 9 å Fasten a STRIKE PLATE (6I) to the RIGHT DOOR (K). Use a BLACK 1/2" FLAT HEAD SCREW (11S). å Fasten two NON ADJUSTABLE HINGES (2H) to the RIGHT DOOR (K). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). 1S BLACK 9/16" LARGE HEAD SCREW (4 used for the HINGES) The NON ADJUSTABLE HINGE will NOT have a gap here. 2H K 11S BLACK 1/2" FLAT HEAD SCREW (1 used for the STRIKE PLATE) 6I Indented holes www.sauder.
Step 10 å å Carefully stand your unit upright. å Fasten a KNOB (52K) to the RIGHT DOOR (K). Use a GOLD 1" MACHINE SCREW (50S). Pro Tip: Lift with your legs. And, you know, your arms. Fasten the RIGHT DOOR (K) to the RIGHT END (A). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). 1S BLACK 9/16" LARGE HEAD SCREW (4 used for the HINGES) 52K A K 50S GOLD 1" MACHINE SCREW (1 used for the KNOB) Page 14 414110 www.sauder.
Step 11 å å å å å å Fasten the remaining HINGES (16H) to the DOORS (J and MM). Use twelve BLACK 9/16" LARGE HEAD SCREWS (1S). Fasten the ADJUSTABLE HINGES (3H) to the LEFT DOOR (MM). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). Fasten the STRIKE PLATE (6I) to the CENTER DOOR (J). Use a BLACK 1/2" FLAT HEAD SCREW (11S). Fasten the SLIDE CATCH (6J) to the CENTER DOOR (J). Use two BROWN 1" FLAT HEAD SCREWS (18S). Place a CASTER BRACKET (17E) over the hole in the bottom edge of CENTER DOOR (J).
Step 12 å Fasten the LEFT DOOR (MM) to the LEFT END (B). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten a KNOB (52K) to each DOOR (J and MM). Use two GOLD 1" MACHINE SCREWS (50S). 1S BLACK 9/16" LARGE HEAD SCREW (4 used for the HINGES) B 52K MM J 50S GOLD 1" MACHINE SCREW (2 used for the KNOBS) Page 16 414110 www.sauder.
Step 13 å NOTE: The FLIP-UP TOP (E) can be supported by the DOORS (J and MM). There are two holes in the bottom surface of the FLIP-UP TOP (E) for the bolt in the SLIDE CATCH (6J) to lock into. å Fasten the TRAYS (2D) to the DOORS (J and MM). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). å Now, slide four TRAY DIVIDERS (3D) into the grooves in each TRAY (2D). If you're doing this to help a friend, don't leave without a bite. E MM J 6J 2D The curved edge of the DIVIDER should be up.
Step 14 å Push the RUBBER SLEEVES (2R) over the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the RIGHT END (A) and UPRIGHT (C2). Set the ADJUSTABLE SHELVES (I) onto the METAL PINS. å å Push a CAM COVER (36P) onto each HIDDEN CAM. å This completes assembly. Clean with a damp cloth. Wipe dry. NOTE: Please read the back pages of the instruction booklet for important safety information.
Desserte couture/ travaux manuels Modèle 414110 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 4 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Fixer l'EXTRÉMITÉ GAUCHE (B) au DESSUS (D2) et au VOILE DE FOND (G2). Serrer quatre EXCENTRIQUES ESCAMOTABLES. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer quatorze EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A et B), le MONTANT (C2), le DESSOUS (F), la VOILE DE FOND (G2) et le TABLETTE (H2).
ÉTAPE 8 ÉTAPE 12 Placer cinq SUPPORTS DE ROULETTE (17E) sur les trous dans le chant inférieur des EXTRÉMITÉS (A et B) et MONTANT (C2). Fixer la PORTE GAUCHE (MM) à l'EXTRÉMITÉ GAUCHE (B). Utiliser quatre VIS TÊTE LARGE 14 mm NOIRES (1S). Enfoncer fermement deux RONDELLES VERROUILLABLES (2CL) dans les trous comme il l’est indiqué dans les SUPPORTS DE ROULETTE (17E) et les EXTRÉMITÉS (A et B). Fixer un BOUTON (52K) à chaque PORTE (J et MM). Utiliser deux VIS À MÉTAUX 25 mm DORÉES (50S).
Modelo 414110 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 3 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Fije el PARAL (C2) al PANEL SUPERIOR (D2) y al FONDO (F). Apriete cuatro EXCÉNTRICOS ESCONDIDOS. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje catorce EXCÉNTRICOS ESCONDIDOS (1F) dentro de los EXTREMOS (A y B), el PARAL (C2), el FONDO (F), el VELO DE FONDO (G2) y el ESTANET (H2).
PASO 6 PASO 8 Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Coloque cinco MÉNSULAS DE RUEDECITA (17E) sobre los agujeros en el borde inferior de los EXTREMOS (A y B) y el PARAL (C2). Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Coloque el DORSO (L) sobre la unidad. Empuje firmemente dos RUEDECITAS CON SEGURO (2CL) en los agujeros como se muestra en las MÉNSULAS DE RUEDECITA (17E) y en los EXTREMOS (A y B).
PASO 10 PASO 13 Fije la PUERTA DERECHA (K) al EXTREMO DERECHO (A). Utilice cuatro TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). NOTA: El PANEL SUPERIOR ABATIBLE HACIA ARRIBA (E) puede ser apoyada por las PUERTAS (J y MM). Hay dos agujeros en la superficie inferior del PANEL SUPERIOR ABATIBLE HACIA ARRIBA (E) para el perno en el SEGURO DE CORREDERA (6J) donde fijarlo. Fije un POMO (52K) a la PUERTA DERECHA (K). Utilice un TORNILLO DORADO PARA METAL de 25 mm (50S).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers or shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
