sauder.com Your holder for all things awesome. Highboy TV Stand Barrister Lane Collection | 414720 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-22 Français pg 23-25 Español pg 26-28 Lot # 372643 05/14/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-22 Hammer Français 23-25 Español 26-28 Safety 29-30 Warranty Not actual size Skip the power trip. This time. 31 ! WARNING Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or death.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 1F HIDDEN CAM - 16 19F MOLDING CONNECTOR - 2 1L 2F CAM DOWEL - 12 40G DOOR HANGER- 8 WARNING LABEL - 1 8F CAM SCREW - 4 5G ANGLE BRACKET - 8 4I DOOR STOP - 4 70K PULL- 4 36M SAFETY STOP - 1 37M DOOR SLIDE - 8 WARNING Never use this furniture with a TV that is too large or too heavy. Severe injury or death can occur. The TV and furniture will be unstable and may tip.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Scan this QR code or go to this address: http://qr.sauder.com/?ID=962 to watch a video on how to assemble your unit. Push sixteen HIDDEN CAMS (1F) into the ENDS (A and B), LOWER ENDS (C and D), UPRIGHTS (E and F), and BOTTOM (H).
Step 2 å Fasten eight DOOR SLIDES (37M) to the ENDS (A and B), LOWER ENDS (C and D), and UPRIGHTS (E and F). Use twelve BROWN 7/16" LARGE HEAD SCREWS (6S). The large hole will be closest to the finished edge of all parts. 37M 6S 37M BROWN 7/16" LARGE HEAD SCREW (12 used in this step) Do not fasten this end of the DOOR SLIDE until step 17. Finished edge 37M Finished edge F 37M 37M D 37M E C 37M 37M 37M B Finished edge A 37M Do not fasten this end of the DOOR SLIDE until step 17.
Step 3 å Fasten the RAILS (R and S) to the TOP (G). Use seven BLACK 1-7/8" FLAT HEAD SCREWS (2S). Rounded edge R Rounded edge S G Su morface re wi ho th les Finished surface R 2S BLACK 1-7/8" FLAT HEAD SCREW (7 used in this step) www.sauder.
Step 4 å Tap two MOLDING CONNECTORS (19F) into the notches in the MOLDINGS (M, N, and O). Use your hammer to tap the MOLDING CONNECTORS (19F) into the notches in the MOLDINGS. Flat end Flat end 19F O 19F M Page 8 414720 N www.sauder.
Step 5 å Fasten the MOLDINGS (M, N, and O) to the TOP (G). Use seven SILVER 1-1/8" FLAT HEAD SCREWS (10S). å NOTE: Do not overtighten the SCREWS into the TOP. 10S SILVER 1-1/8" FLAT HEAD SCREW (7 used in this step) Do not overtighten the SCREWS (10S). O G M N Finished surface www.sauder.
Step 6 å Turn four CAM SCREWS (8F) into the MOLDINGS (N and O). O N 8F Page 10 414720 www.sauder.
Step 7 å Fasten the ENDS (A and B) to the MOLDINGS (N and O). Tighten four HIDDEN CAMS. å Fasten the UPRIGHT (E) to the TOP (G). Tighten two HIDDEN CAMS. 1 2 Finished edge O B G h wit MS e A c rfa C Su DEN D HI E Finished edge h wit MS e A c rfa C Su DEN D HI Finished edge Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: www.sauder.
Step 8 å Fasten the SHELF (I) to the ENDS (A and B) and UPRIGHT (E). Use six BLACK 1-7/8" FLAT HEAD SCREWS (2S). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Rounded edge B E I A Su morface re wi ho th les 2S BLACK 1-7/8" FLAT HEAD SCREW (6 used in this step) Page 12 414720 www.sauder.
Step 9 å Fasten the LOWER ENDS (C and D) and LOWER UPRIGHT (F) to the SHELF (I). Tighten six HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees Finished edge D h wit MS e A c rfa C Su DEN D HI Finished edge I F h wit MS e A c rfa C Su DEN D HI Finished edge www.sauder.
Step 10 å Fasten the BOTTOM (H) to the LOWER ENDS (C and D). Tighten four HIDDEN CAMS. å Fasten the BOTTOM (H) to the LOWER UPRIGHT (F). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S) Maximum 210 degrees Arrow Minimum 190 degrees These holes must be here. D F H Su HI rface DD w EN ith CA MS C 2S BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) Page 14 414720 www.sauder.
Step 11 å å Fasten eight ANGLE BRACKETS (5G) to the LOWER ENDS (C and D), BOTTOM (H), and BRACE (K). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). (8 used) NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edges of the ENDS, BOTTOM, and BRACE. 5G 1S 5G K BLACK 9/16" LARGE HEAD SCREW (8 used in this step) 5G 5G 5G D H C 5G www.sauder.
Step 12 å å Carefully turn your unit over onto its front edges. Fasten the BRACE (K) to the LOWER ENDS (C and D) and BOTTOM (H). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). 1S BLACK 9/16" LARGE HEAD SCREW (4 used in this step) C H K D Page 16 414720 www.sauder.
Step 13 å å Unfold the BACK (J) and lay it over your unit. å å Fasten the BACK (J) to your unit using the NAILS (1N). å NOTE: Perforations have been provided for access through the BACK. Carefully cut out the holes needed. Caution Make equal margins along all two long edges and the two short edges of the BACK (J). Push on opposite corners of your unit if needed to make it "square". Do not stand the unit upright without the BACK fastened. The unit may collapse.
Step 14 å Fasten the FRONT BASE (P) to the ENDS (C and D) and BOTTOM (H). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten the SIDE BASES (Q) to the LOWER ENDS (C and D). Use four BROWN 1" FLAT HEAD SCREWS (12S). Unfinished surface Q C H D ed h is fin n U Q e ac rf su 1S Finished surface P BLACK 9/16" LARGE HEAD SCREW (4 used for the BRACKETS) 12S BROWN 1" FLAT HEAD SCREW (4 used for the SIDE BASES) Page 18 414720 www.sauder.
Step 15 å å Carefully stand your unit upright. å Fasten the SAFETY STOP (36M) to the TOP (G). Use two SILVER 5/8" MACHINE SCREWS (15S). å Push the RUBBER SLEEVES (2R) over the METAL PINS (1R). Insert the METAL PINS into the holes in the ENDS (A, B, C and D) and UPRIGHTS (E and F). These are used for door stops when the DOORS are open. Push four DOOR STOPS (4I) into the holes in the UPRIGHTS (E and F). The SAFETY STOP is a safety feature that positions your TV away from the front edge of the unit.
Step 16 å Fasten a PULL (70K) to a DOOR (L). Use two GOLD 1" MACHINE SCREWS (50S). å Fasten two DOOR HANGERS (40G) to the DOOR. Use two BLACK 9/16" LARGE HEAD SCREWS (1S). å Repeat this step for the other DOORS. 1S BLACK 9/16" LARGE HEAD SCREW (8 used for the DOOR HANGERS) (8 used) 40G 50S GOLD 1" MACHINE SCREW (8 used for the PULLS) L 70K Page 20 414720 www.sauder.
Step 17 å Before you begin fastening the remaining DOOR SLIDES (37M), you must insert the DOOR (L) at an angle placing the DOOR HANGERS behind the large hole on the DOOR SLIDES. Push the door into the unit horizontally. å While holding the DOOR, swing the DOOR SLIDE up into place and fasten it using a BROWN 7/16" LARGE HEAD SCREW (6S). å Repeat this step to hang the remaining DOORS.
Step 18 å Apply the WARNING LABEL (1L) to the TOP (G). You should be able to read the label when the TV is removed from the unit. When the TV is in place, it should hide the label. Peel off the backing and apply the label as shown in the diagram. å å å NOTE: This is a permanent label intended to last for the life of the product. Once applied, do not try to remove it. NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly.
414720 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
AVERTISSEMENT ÉTAPE 4 L'utilisation d'un téléviseur trop lourd ou trop gros est dangereuse. Un téléviseur trop lourd créera un risque de basculement pouvant provoquer de graves blessures ou la mort. Un téléviseur trop gros pour l'espace disponible risque d'être accidentellement poussé ou de tomber du mobilier ou d'être sujet à basculer. Enfoncer deux CONNECTEURS DE MOULURE (19F) dans les crans des MOULURES (M, N et O). • Vérifier la taille et le poids du téléviseur.
ÉTAPE 11 ÉTAPE 15 Fixer huit CONSOLES À ÉQUERRE (5G) aux EXTRÉMITÉS INFÉRIEURES (C et D), au DESSOUS (H) et à l'ENTRETOISE (K). Utiliser huit VIS TÊTE LARGE 14 mm NOIRES (1S). Relever, avec précaution, l'élément dans sa position verticale. REMARQUE : S'assurer que les chants des CONSOLES À ÉQUERRE sont à fleur des chants des EXTRÉMITÉS, DESSOUS et de l'ENTRETOISE. Fixer l’ARRÊT DE SÉCURITÉ (36M) au DESSUS (G). Utiliser deux VIS À MÉTAUX 15 mm ARGENT (15S).
414720 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
ADVERTENCIA PASO 4 El uso de un televisor demasiado pesado o grande es peligroso. Un televisor demasiado pesado generará riesgo de caída, lo cual podría causar lesiones graves o muerte. Un televisor demasiado grande para el espacio disponible puede ser empujado o golpeado por accidente, causando que éste se salga del mueble o se caiga. Ligeramente clave dos CONECTORES DE MOLDURA (19F) dentro de las muescas de las MOLDURAS (M, N y O). • Verifique el tamaño y peso del televisor.
PASO 11 PASO 15 Fije ocho SOPORTES ANGULARES (5G) a los EXTREMOS INFERIORES (C y D), al FONDO (H) y a la RIOSTRA (K). Utilice ocho TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). Cuidadosamente ponga la unidad en posición vertical. NOTA: Asegúrese que los bordes de los SOPORTES ANGULARES estén nivelados con los bordes de los EXTREMOS, del FONDO y de la RIOSTRA. Fije la MOLDURA DE TOPE (36M) al PANEL SUPERIOR (G). Utilice dos TORNILLOS PLATEADOS PARA METAL de 15 mm (15S).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Children climbing on furniture. • A child may try to reach a toy or other object by climbing on furniture. • Children will play and be active near the TV. • Risk of injury or death.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Los niños subiendo al mobiliario. • El niño que intenta a alcanzar un juego u otro objeto subiendo al mobiliario. • Los niños jugarán y estarán activos cerca del televisor. • Riesgo de lesiones o la muerte.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
