sauder.com Here's one for the books. Bookcase Barrister Lane Collection | Model 414726 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-16 Français pg 17-18 Español pg 19-20 Lot # 362947 06/18/14 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification 2-3 Hardware Identification Assembly Steps Assembly Tools Required No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-16 Hammer Français 17-18 Español 19-20 Safety 21-22 Warranty Not actual size Skip the power trip. This time. 23 Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Now you know our ABCs. Part Identification L M O L F N P I I D C A D H Q E H H Q K E B G H J G K www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 1F HIDDEN CAM - 38 1G SAFETY BRACKET - 1 38M CARD SHEET - 1 2F CAM DOWEL - 38 19F MOLDING CONNECTOR - 2 27G ANGLE BRACKET - 6 1N 35M CARD HOLDER - 8 13P CAM COVER - 6 NAIL - 91 18P SCREW COVER - 5 1S 1R 2S BLACK 9/16" LARGE HEAD SCREW - 13 12S BROWN 1" FLAT HEAD SCREW - 13 Page 4 METAL PIN - 8 BLACK 1-7/8" FLAT HEAD SCREW - 18 97S SILVER 3/8" MACHINE SCREW - 16 414726 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Scan this QR code or go to this address: http://qr.sauder.com/?ID=1711 to watch a video on how to assemble your unit. Push thirty-eight HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHT (C), BOTTOMS (G), and SHELVES (H). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM.
Step 2 å Tap two MOLDING CONNECTORS (19F) into the notches in the MOLDINGS (N, O, and P). Use your hammer to tap the MOLDING CONNECTORS (19F) into the notches in the MOLDINGS. Flat end Flat end 19F 19F P N Page 6 414726 O www.sauder.
Step 3 å Fasten the RAILS (L and M) to the TOP (F). Use nine BLACK 1-7/8" FLAT HEAD SCREWS (2S). Remember: Righty tighty. Lefty loosey. Finished surface L M ce rfa Su F th wi es ol rh we fe L Long finished edge 2S BLACK 1-7/8" FLAT HEAD SCREW (9 used in this step) www.sauder.
Step 4 å å Carefully turn your TOP over. å NOTE: Do not overtighten the SCREWS into the TOP. Fasten the MOLDINGS (N, O, and P) to the TOP (F). Use nine BROWN 1" FLAT HEAD SCREWS (12S). O 12S BROWN 1" FLAT HEAD SCREW (9 used in this step) N th wi ce les rfa ho Su ore m F P Long finished edge Page 8 414726 www.sauder.
Step 5 å å å Fasten the UPRIGHT (C) to the TOP (F). Tighten two HIDDEN CAMS. Caution Insert four METAL PINS (1R) into the UPPER UPRIGHTS (D). Do not stand the unit upright without the BACK fastened. The unit may collapse. Insert the METAL PINS (1R) in the end of the UPPER UPRIGHTS (D) into the holes in the TOP (F). 1R Long finished edge Finished edge Finished edge F D Sur mo face w re h ith ole s C D ith e w AMS c a f Sur DEN C HID 1R Caution Risk of damage or injury.
Step 6 å Fasten two SHELVES (H) to the UPRIGHT (C). Tighten four HIDDEN CAMS. å Fasten the SHELVES (H) to the UPPER UPRIGHTS (D). Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S). å å Insert four METAL PINS (1R) into the LOWER UPRIGHTS (E). Maximum 210 degrees Arrow Minimum 190 degrees Insert the METAL PINS (1R) in the end of the LOWER UPRIGHTS (E) into the holes in the SHELVES (H).
Step 7 å Fasten the remaining two SHELVES (H) to the UPRIGHT (C). Tighten four HIDDEN CAMS. å Fasten the SHELVES (H) to the LOWER UPRIGHTS (E). Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S). å Fasten the BOTTOMS (G) to the UPRIGHT (C). Tighten four HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees Long edge with HIDDEN CAMS These holes must be here.
Step 8 å Fasten the ENDS (A and B) to the MOLDINGS (O and P), BOTTOMS (G), and SHELVES (H). Tighten sixteen HIDDEN CAMS. å Fasten the SIDE SKIRTS (K) to the ENDS (A and B). Use four BROWN 1" FLAT HEAD SCREWS (12S). Finished edge Maximum 210 degrees Arrow Minimum 190 degrees P B Finished edge ith ce wN a f r Su IDDE H MS CA K F Finished edge H H H G H A ut itho S w e fac AM Sur DEN C HID G O 12S K BROWN 1" FLAT HEAD SCREW (4 used in this step) Finished edge Page 12 414726 www.
Step 9 å Fasten six ANGLE BRACKETS (27G) to the ENDS (A and B) and BOTTOMS (G). Use six BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edges of the ENDS and BOTTOMS. å Fasten the FRONT SKIRT (J) to the ENDS (A and B) and BOTTOMS (G). Use six BLACK 9/16" LARGE HEAD SCREWS (1S) through the ANGLE BRACKETS and into the FRONT SKIRT.
Step 10 å å Fasten four CARD HOLDERS (35M) to each SHELF MOLDING (Q). Use sixteen SILVER 3/8" MACHINE SCREWS (97S). Card slot Fasten the SHELF MOLDINGS (Q) to the SHELVES (H). Tighten eight HIDDEN CAMS. 35M (8 used) Q Unfinished surface Maximum 210 degrees Arrow Q Unfinished surface Minimum 190 degrees 97S Q SILVER 3/8" MACHINE SCREW (16 used for the CARD HOLDERS) Q H H H H Page 14 414726 www.sauder.
Step 11 å Carefully turn your unit over onto its front edges. Unfold one of the BACKS (I) and lay it over your unit. å Make equal margins along all four edges of the BACK (I). Push on opposite corners of your unit if needed to make it "square". å Fasten the BACK (I) to your unit using the NAILS (1N). Do not fasten the edge that lays over the UPRIGHT. å Next, fasten the other BACK (I) to your unit using the NAILS. The BACKS will overlap each other. See the enlarged diagram.
Step 12 å å Carefully stand your unit upright. å å å å å Center a SCREW COVER (18P) over the head of each visible SCREW and press firmly. We recommend using the SAFETY BRACKET (1G) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (1S) into the underneath surface of the TOP and a BLACK 1-7/8" FLAT HEAD SCREW (2S) into a stud in your wall. Push a CAM COVER (13P) onto each visible HIDDEN CAM. Separate the CARDS on the CARD SHEET (38M) and insert into the CARD HOLDERS.
Modèle 414726 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 8 Ne pas serrer les CAMES ESCAMOTABLES dans cette étape. Fixer les EXTRÉMITÉS (A et B) aux les MOULURES (O et P) , les DESSOUS (G) et les TABLETTES (H). Serrer seize EXCENTRIQUES ESCAMOTABLES. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer trente-huit EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A et B), le MONTANT (C), les DESSOUS (G) et les TABLETTES (H).
Modelo 414726 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 8 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Fije los EXTREMOS (A y B) a las MOLDURAS (O y P), los FONDOS (G) y los ESTANTES (H). Apriete dieciséis EXCÉNTRICOS ESCONDIDOS. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje treinta y ocho EXCÉNTRICOS ESCONDIDOS (1F) dentro de los EXTREMOS (A y B), el PARAL (C), los FONDOS (G) y los ESTANTES (H).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes sobrecargados • Cargar el producto inadecuadamente puede causar la inestabilidad. • Riesgo de lesiones. • El mobiliario inestable puede volcarse. • Estantes sobrecargados pueden romper.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
