sauder.com Stuff a sock in it. Or two. 5-Drawer Chest Harbor View Collection | 414941 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-18 Français pg 19-21 Español pg 22-24 Lot # 364751 08/28/14 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Assembly Tools Required 2-3 Hardware Identification No. 2 Phillips Screwdriver Tip Shown Actual Size 4 Assembly Steps 5-18 Hammer Français 19-21 Español 22-24 Safety 25-26 Warranty Not actual size Skip the power trip. This time. 27 Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Part Identification K C D24 D170 D945 H N D25 L P F E D30 D171 O A D945 F D31 P G B F D D J Q M D945 D31 Q www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (10F) into the large holes in the BRACES (D and E). å NOTE: Do not push any TWIST-LOCK® FASTENERS into the indicated holes in the UPPER BRACE (E) at this time.
Step 2 å Push eleven HIDDEN CAMS (1F) into the BACKS (F) and DRAWER BRACES (P). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. Arrow 2F (11 used) 1F F F Arrow F P P P P P Insert the metal end of the CAM DOWEL into the HIDDEN CAM. Arrow 1F 2F Page 6 414941 www.sauder.
Step 3 å Fasten five CABINET RIGHTS (35GA) to the RIGHT END (A) and five CABINET LEFTS (35GB) to the LEFT END (B). Use twenty GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. Remember: Righty tighty. Lefty loosey. 1 2 3 Roller end 1 2 1 3 Finished edge 2 3 1 3 2 A 1 S ho urfa le ce s w ith 3 2 3 1 2 1 3 2 3 2 3 1 S ho urfa le ce s w ith B 2 3 1 2 1 Roller end Finished edge 3S GOLD 5/16" FLAT HEAD SCREW (20 used in this step) www.sauder.
Step 4 å Tap two MOLDING CONNECTORS (16F) into the notches in the MOLDINGS (K, L, and N). Use your hammer to tap the MOLDING CONNECTOR (16F) into the notches in the MOLDINGS Flat end Flat end 16F 16F L K N Page 8 414941 www.sauder.
Step 5 å å å First, fasten the SKIRT (M) to the BOTTOM MOLDING (J). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). Then, fasten the BOTTOM MOLDING (J) to one of the LOWER BRACES (D). Use four BLACK 1-1/8" PAN HEAD SCREWS (9S). Fasten the MOLDING (O) to the UPPER BRACE (E). Tighten three TWIST-LOCK® FASTENERS. Rounded edge These holes must be here.
Step 6 å å Insert three METAL PINS (1R) into the BACKS (F). å NOTE: Be sure the METAL PINS in the BACKS (F) insert into the holes in the LEFT END (B). Fasten the BACKS (F) to the LEFT END (B). Tighten three HIDDEN CAMS. Finished edge 1R B e fac Sur withes hol S ith M w A ce C fa EN ur D S ID H F Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate.
Step 7 å Fasten the LEFT MOLDING (L) to the LEFT END (B). Use two BLACK 2-1/4" FLAT HEAD SCREWS (26S). å å Insert two METAL PINS (1R) into the LOWER BRACES (D). å NOTE: When fastening the LOWER BRACES (D), you may need someone's help. Be sure the METAL PINS in the LOWER BRACES insert into the holes in the LEFT END (B). Don't worry. It isn't Rome. This can be built in a day. Fasten the LOWER BRACES (D) to the LEFT END (B). Tighten two TWIST-LOCK® FASTENERS.
Step 8 å å Insert five METAL PINS (1R) into the LOWER BRACES (D) and BACKS (F). å NOTE: Be sure the METAL PINS in the LOWER BRACES (D) and BACKS (F) insert into the holes in the RIGHT END (A). å Fasten the RIGHT END (A) to the RIGHT MOLDING (K). Use two BLACK 2-1/4" FLAT HEAD SCREWS (26S). å Now, fasten the TOP (C) to the MOLDINGS (K, L, and N). Use seven BLACK 1-5/8" PAN HEAD SCREWS (27S). Maximum 210 degrees Fasten the RIGHT END (A) to the LOWER BRACES (D) and BACKS (F).
Step 9 å Insert the dowel end of four TWIST-LOCK® FASTENERS (10F) into the ENDS (A and B) as shown. Follow the enlarged diagram closely. å NOTE: If you already pushed the TWIST-LOCK® FASTENERS into the large holes in the UPPER BRACE (E), pull the FASTENERS back out of the holes. Pull at the front and back edges, slowly working the FASTENERS out of the holes. å Push the UPPER BRACE (E) onto the TWIST-LOCK® FASTENERS in the ENDS (A and B). Now, tighten the TWIST-LOCK® FASTENERS.
Step 10 VIEW THE T-LOCK BOX VIDEO The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. 1 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. 2 D945 Un fi su nish rfa ed ce D30 D30 I D31 I D31 Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Groove å Insert the DRAWER SIDES (D30 and D31) at an angle into the slot at each end of the LOWER DRAWER FRONT (I).
Step 11 å Insert a SLIDE CAM (10A) into the DRAWER SIDES (D30 and D31). å Fasten a DRAWER RIGHT (35GC) to the DRAWER RIGHT SIDE (D30) and a DRAWER LEFT (35GD) to the DRAWER LEFT SIDE (D31). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. å Repeat this step for the other drawers. Almost time to celebrate! With a nap.
Step 12 å å Fasten two KNOBS (5K) to the SMALL DRAWER FRONT (H). Use two BLACK 1-1/8" MACHINE SCREWS (21S). å å NOTE: The drawer with the WARNING LABEL should be inserted into the top of your unit as shown in the next step. Apply the WARNING LABEL (5L) to the small drawer's DRAWER BOTTOM (D945). You should be able to read the label when the drawer is open. When the drawer is closed, it will hide the label. Peel off the backing and apply the label as shown in the diagram.
Step 13 å å å Carefully stand your unit upright. Position your unit in its final location. We recommend using the SAFETY STRAP (60M) for added stability. NOTE: Do not turn the SAFETY DRYWALL ANCHOR (61M) into a wall stud. If you prefer to fasten the SAFETY STRAP (60M) to a wall stud, go to your local hardware store for proper hardware. å INSTALLATION INSTRUCTIONS: (Also available at www.yl-anchors.com) 1.
Step 14 å To make adjustments to the drawers, loosen SCREW #3 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawers this way, it will help the DRAWER FRONTS line up better when closed. Tighten the SCREW when finished with adjustments.
414941 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (10F) dans les gros trous des ENTRETOISES (D et E). REMARQUE : Ne pas enfoncer les FIXATIONS TWIST-LOCK® dans les trous indiqués de l'ENTRETOISE SUPÉRIEURE (E) à ce stade de l'assemblage.
ÉTAPE 9 (SUITE) ÉTAPE 13 Ensuite, faire tourner un PIED (Q) sur l’autre extrémité de chaque VIS DE PIED (23F). Faire tourner les PIEDS dans le sens des aiguilles d’une montre jusqu’à ce que la VIS DE PIED soit serrée dans la MOULURE DE DESSOUS (J) et chaque PIED. Relever, avec précaution, l'élément dans sa position verticale. Placer l'élément dans son emplacement final. Il est recommandé d’utiliser la SANGLE DE SÉCURITÉ (60M) pour stabilité additionnelle.
414941 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 No apriete los SUJETADORES TWIST-LOCK® en este paso. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (10F) dentro de los agujeros grandes de las RIOSTRAS (D y E). NOTA: No empuje SUJETADORES TWIST-LOCK® dentro de agujeros indicados de la RIOSTRA SUPERIOR (E) por ahora. Si necesita sacar un SUJETADOR TWIST-LOCK® de un agujero, retire el SUJETADOR del agujero.
PASO 9 (CONTINUACIÓN) PASO 13 Posteriormente, gire un PIE (Q) hacia el otro extremo de cada TORNILLO DE PIE (23F). Gire los PIES en dirección de las manecillas del reloj, hasta que quede sujetado el TORNILLO DE PIE en la MOLDURA DE FONDO (J) y cada PIE. Cuidadosamente ponga la unidad en posición vertical. Coloque su unidad en su posición final. Se recomienda utilizar la CORREA DE SEGURIDAD (60M) para mayor estabilidad. NOTA: No gire el ANCLAJE DE SEGURIDAD PARA EL DRYWALL (61M) en un montante de la pared.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: •Cajones y estantes de cómoda sobrecargados. • Un riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones o estantes sobrecargados pueden romperse. • Nunca exceder los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
