sauder.com Deep shelves for tall tales. 3-Shelf Bookcase 415541 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-8 Français pg 9-10 Español pg 11-12 Lot # 374928 06/30/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-8 Hammer Français 9-10 Español 11-12 Safety 13-14 Warranty Page 2 Not actual size Skip the power trip. This time. 15 415541 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. A2 END (2) B TOP/BOTTOM (2) C BACK (1) E2 ADJUSTABLE SHELF (2) C B E2 A2 E2 A2 B www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. E METAL PIN - 8 F RUBBER SLEEVE - 8 G APPLIQUE CARD - 2 I NAIL - 24 113S Page 4 BLACK 1-15/16" FLAT HEAD SCREW - 8 415541 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Remember: Righty tighty. Lefty loosey. Fasten the ENDS (A2) to the TOP/BOTTOMS (B). Use eight BLACK 1-15/16" FLAT HEAD SCREWS (113S). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse.
Step 2 å Fasten the BACK (C) to the unit using the NAILS (I). Square the unit to the BACK, making sure there is an equal margin along all edges. The NAILS should be approximately 5" apart and 1/4" in from the edges. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. I NAIL (24 used in this step) ed ish fin ce Un rfa su C approximately 5" 1-1/2" 1/4" Page 6 415541 www.sauder.
Step 3 å å Carefully stand your unit upright. Pro Tip: Lift with your legs. And, you know, your arms. Push the RUBBER SLEEVES (F) over the METAL PINS (E). Insert the METAL PINS into the hole locations of your choice in the ENDS (A2). Set the ADJUSTABLE SHELVES (E2) onto the METAL PINS. E2 A2 E2 A2 E F (8 used) www.sauder.
Step 4 å Peel the APPLIQUES from the APPLIQUE CARD (G). Stick the APPLIQUES over the SCREW heads in the ENDS (A2). å NOTE: Please read the back page of the instruction booklet for important safety information. å This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. And to celebrate, why not share your success story? 25 lbs. 25 lbs. A2 25 lbs. A2 40 lbs. G (8 used) Page 8 415541 www.sauder.
415541 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 3 Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Relever, avec précaution, l'élément dans sa position verticale. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Fixer les EXTRÉMITÉS (A2) aux pièces DESSUS/DESSOUS (B). Utiliser huit VIS NOIRES TÊTE PLATE 49 mm (113S). Enfoncer les MANCHONS EN CAOUTCHOUC (F) sur les GOUPILLES EN MÉTAL (E).
415541 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 3 Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Cuidadosamente ponga la unidad en posición vertical. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Fije los EXTREMOS (A2) a las partes PANEL SUPERIOR/FONDO (B). Utilice ocho TORNILLOS NEGROS DE CABEZA PERDIDA de 49 mm (113S). PASO 2 Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes sobrecargados. • Cargar el producto inadecuadamente puede causar la inestabilidad. • Riesgo de lesiones. • El mobiliario inestable puede volcarse. • Estantes sobrecargados pueden romper.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
