415547 Twin Bookcase Headboard PLEASE CONTACT US BEFORE RETURNING YOUR UNIT TO THE STORE 1-800-523-3987 www.sauder.com NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. English .................... Page 1-14 Français ...............Pages 15-16 Made in the USA Archbold, OH Espanol.............
TABLE OF CONTENTS ADULT ASSEMBLY REQUIRED Part Identification .......................3 Hardware Identification .............4 ASSEMBLY TOOLS REQUIRED Assembly Steps .................... 5-14 No. 2 Phillips Screwdriver Français .............................. 15-16 Tip Shown Actual Size Espanol............................... 17-18 Warranty ...................................19 Hammer Electric drill with 1/4" bit (ONLY in indicated step) Page 2 www.sauder.
PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help identify similar parts. A RIGHT END 1 E SHELF 1 B LEFT END 1 F BACK 1 C UPRIGHT 1 G PANEL 2 D TOP 1 H ADJUSTABLE SHELF 2 D H F A H C E G G B 415547 www.sauder.
HARDWARE IDENTIFICATION 2F CAM DOWEL - 18 1F HIDDEN CAM - 18 16G HEADBOARD BRACKET - 2 1N NAIL - 35 27G ANGLE BRACKET - 2 19P CAM COVER - 6 1R 3G TIE PLATE - 2 13M WASHER - 4 METAL PIN - 8 1S BLACK 9/16" LARGE HEAD SCREW - 16 2S 9S BLACK 1-1/8" PAN HEAD SCREW - 2 94S SILVER 2" BOLT - 4 24M NUT - 4 2R RUBBER SLEEVE - 8 BLACK 1-7/8" FLAT HEAD SCREW - 2 102S SILVER 1" LARGE HEAD SCREW - 2 Screws are shown actual size. You may receive extra hardware with your unit. Page 4 www.sauder.
S p te Look for this icon. It means a video assembly tip is available at: www.sauder.com/services/tips 1 2F (18 used) Do not tighten the HIDDEN CAMS in this step. Arrow 1F G G E D Arrow C Insert the metal end of the CAM DOWEL into the HIDDEN CAM. Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Push eighteen HIDDEN CAMS (1F) into the UPRIGHT (C), TOP (D), SHELF (E), and both PANELS (G).
S p te 2 Finished edge E ith w ace f r Su DEN HID S M CA Curved edge S w ur ho it fa le h ce s A Fasten the SHELF (E) to the RIGHT END (A). Tighten two HIDDEN CAMS. Caution Risk of damage or injury. Hidden Cams must be completely tightened. Hidden Cams that are not completely tightened may loosen, and parts may separate. To completely tighten: Page 6 Start Arrow Tighten Maximum 210 degrees Arrow Minimum 190 degrees www.sauder.
S p te 3 Finished edge D e fac r u S h wit DEN HID S M CA C Surface with HIDDEN CAMS 2S E BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) A Maximum 210 degrees Arrow Minimum 190 degrees Fasten the UPRIGHT (C) to the SHELF (E). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). Fasten the TOP (D) to the RIGHT END (A) and UPRIGHT (C). Tighten four HIDDEN CAMS. 415547 www.sauder.
S p te 4 1S BLACK 9/16" LARGE HEAD SCREW (4 used for the BRACKETS) G These holes must be here. E Sur f HIDace w it CA DEN h MS A 27G G Arrow h M it A w C ce N fa E ur D S ID H Maximum 210 degrees Minimum 190 degrees S Fasten two ANGLE BRACKETS (27G) to one of the PANELS (G). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edge of the PANEL. Fasten the PANEL (G) to the RIGHT END (A). Tighten two HIDDEN CAMS.
S p te 5 G G Sur f HIDace w it CA DEN h MS These holes must be here. A 3G Maximum 210 degrees 1S Arrow Minimum 190 degrees BLACK 9/16" LARGE HEAD SCREW (4 used in this step) Fasten the remaining PANEL (G) to the RIGHT END (A). Tighten two HIDDEN CAMS. Fasten the PANEL (G) to the other PANEL (G). Use two TIE PLATES (3G) and four BLACK 9/16" LARGE HEAD SCREWS (1S). 415547 www.sauder.
S p te 6 Curved edge S w ur ho it fa le ho ce s ut B D E G G Maximum 210 degrees Arrow Minimum 190 degrees Fasten the LEFT END (B) to the TOP (D), SHELF (E), and both PANELS (G). Tighten eight HIDDEN CAMS. Page 10 www.sauder.
S Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. p te 7 These holes must line up over the UPRIGHT (C). U n fi ni sh ed su rf ac e F 1N NAIL (35 used in this step) Carefully turn your unit over onto its front edges. Unfold the BACK (F) and lay it over your unit. Make equal margins along all four edges of the BACK (F). Push on opposite corners of your unit if needed to make it “square”. Fasten the BACK (F) to your unit using the NAILS (1N).
S p te 8 B 16G A 16G 1S BLACK 9/16" LARGE HEAD SCREW (8 used in this step) NOTE: If fastening your Headboard to the 415546 Split-Platform Bed with Storage, go to Step 10 now. Fasten the HEADBOARD BRACKETS (16G) to the ENDS (A and B). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). NOTE: Select the holes to use for the correct height of your bed frame. Page 12 www.sauder.
S p te 9 13M H 5 lbs. B 19P 24M 10 lbs. (6 used) C To cover HIDDEN CAMS 20 lbs. H 5 lbs. 94S A 16G 1R (8 used) 2R 94S 13M SILVER 2” BOLT WASHER (4 of each used for the bedframe) 16G 24M NUT Carefully stand your unit upright. Push the RUBBER SLEEVES (2R) over the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B) and UPRIGHT (C). Set the ADJUSTABLE SHELVES (H) onto the METAL PINS.
S p te 10 Finish drilling these two holes using a 1/4" drill bit. 1S in w d T Be 46 m 55 for 41 lat P BLACK 9/16" LARGE HEAD SCREW (8 used for the HEADBOARD BRACKETS) A G 16G B 415546 Headboard 9S 102S BLACK 1-1/8" PAN HEAD SCREW (2 used in this step) SILVER 1" LARGE HEAD SCREW (2 used in this step) IMPORTANT: Remove the Headboard from the Platform Bed when moving. Carefully stand your unit upright. Fasten the HEADBOARD BRACKETS (16G) to the ENDS (A and B).
Tête de Lit-Bibliothèque pour lit une place 415547 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 7 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer dix-huit EXCENTRIQUES ESCAMOTABLES (1F) dans le MONTANT (C), le DESSUS (D), la TABLETTE (E) et les deux PANNEAUX (G). Ensuite, insérer l'extrémité en métal de la CHEVILLE D'EXCENTRIQUE (2F) dans chaque EXCENTRIQUE ESCAMOTABLE.
Cabecera para cama sencilla con biblioteca 415547 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 7 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje dieciocho EXCÉNTRICOS ESCONDIDOS (1F) dentro del PARAL (C), del PANEL SUPERIOR (D), del ESTANTE (E) y los dos PANELES (G). A continuación, inserte el extremo de metal de un PASADOR DE EXCÉNTRICO (2F) dentro de cada EXCÉNTRICO ESCONDIDO. Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear valued customer: Thank you for your purchase from the Sauder family companies. It’s our pleasure to provide you with an affordable solution that meets your furniture and storage needs. I hope you will enjoy it for years to come. I am pleased with this company’s consistent ability to amaze the customer over time. My grandfather, Erie Sauder, founded the company in 1934 and later invented and patented the first commercially successful ready-to-assemble table.