sauder.com You could use a new hide-and-seek spot. Armoire County Line Collection | Model 415995 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-22 Français pg 23-25 Español pg 26-28 Lot # 375987 07/22/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-22 Hammer Français 23-25 Español 26-28 Safety 29-30 Warranty Page 2 Not actual size Skip the power trip. This time. 31 415995 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 40DA UNIVERSAL CABINET RAIL - 2 8F CAM SCREW - 9 10F 14H HINGE - 4 4I 40DC DRAWER RIGHT - 1 TWIST-LOCK® FASTENER - 12 40DD DRAWER LEFT - 1 15F WOOD DOWEL - 2 DOOR STOP - 2 10I WASHER - 2 11L WARNING LABEL - 1 10/16 SAFETY BRACKET - 1 1G WARNING AVERTISSEMENT ADVERTENCIA Des blessures graves ou fatales par écrasement peuvent survenir si le mobilier bascule.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (10F) into the large holes in the ENDS (A2 and B2). å Repeat this step for the BOTTOM (D) and SHELF (E). Do not tighten the TWIST-LOCK® FASTENERS in this step. 10F (12 used) A2 B2 www.sauder.
Step 2 å Turn nine CAM SCREWS (8F) into the LEGS (I and J) and DRAWER FRONT (M). å Push nine HIDDEN CAMS (1F) into the ENDS (A2 and B2) and DRAWER BRACE (M65). 8F (9 used) I J M Arrow 1F A2 B2 Arrow Arrow 1F (9 used) M65 Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. Page 6 415995 www.sauder.
Step 3 å å Insert two WOOD DOWELS (15F) into the ENDS (A2 and B2). å NOTE: Be sure the WOOD DOWELS in the ENDS insert into the holes in the FRONT LEGS. Fasten the FRONT LEGS (I and J) to the ENDS (A2 and B2). Tighten eight HIDDEN CAMS. 1 2 These surfaces must be even. These surfaces must be even. 15F I S HI urfa DD ce EN wi CA th M S A2 S HI urfa DD ce EN wi CA th M S B2 J 15F www.sauder.com/services The LEG should overhang this edge.
Step 4 å Fasten the BACK LEGS (K) to the ENDS (A2 and B2). Use eight BLACK 2-1/4" FLAT HEAD SCREWS (26S). Remember: Righty tighty. Lefty loosey. These surfaces must be even. A2 K K B2 The LEG should overhang this edge. 26S BLACK 2-1/4" FLAT HEAD SCREW (8 used in this step) Page 8 415995 www.sauder.
Step 5 VIEW THE DRAWER GLIDE VIDEO å Fasten the UNIVERSAL CABINET RAILS* (40DA) to the ENDS (A2 and B2). Use four GOLD 5/16" FLAT HEAD SCREWS (3S). å *patent pending glide system 3S GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Glide end A2 1 2 4 3 B2 3 4 2 1 Glide end www.sauder.
Step 6 å Fasten the LEFT END (B2) to the TOP (C). Tighten two TWIST-LOCK® FASTENERS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible.
Step 7 å Fasten the SHELF (E) to the LEFT END (B2). Tighten two TWIST-LOCK® FASTENERS. Finished edge B2 Sur fac ew ith T www.sauder.
Step 8 å Fasten the BOTTOM (D) to the LEFT END (B2). Tighten two TWIST-LOCK® FASTENERS. å Slide the BOTTOM SKIRT* (L) onto the notched edge of the BOTTOM (D). å *U.S. Patent No. 5,499,886 Notched edge B2 Sur fac ew ith T D WIS T-L O L CK ® FA STE NER S Slide the BOTTOM SKIRT (L) onto the notched edge. Page 12 415995 Groove www.sauder.
Step 9 å å Fasten the RIGHT END (A2) to the TOP (C), BOTTOM (D), and SHELF (E). Tighten six TWIST-LOCK® FASTENERS. Don't worry. It isn't Rome. This can be built in a day. Push two DOOR STOPS (4I) into the holes in the TOP (C). 4I C ut itho S w e fac AM Sur DEN C HID I E A2 D www.sauder.
Step 10 å Carefully turn your unit over onto its front edges. Unfold the BACK (F) and lay it over your unit. å Make equal margins along all four edges of the BACK (F). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (F) to your unit using the NAILS (1N). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. NOTE: Be sure to tap NAILS into the holes that line up over the SHELF (E).
Step 11 å Fasten two HINGES (14H) to each DOOR (G). Use eight BLACK 1/2" FLAT HEAD SCREWS (11S). 11S BLACK 1/2" FLAT HEAD SCREW (8 used in this step) 14H G G 14H www.sauder.
Step 12 å å Carefully stand your unit upright. å Fasten the DOOR (G) to the LEFT END (B2) as shown in the lower diagram. Use the screws in the HINGES. You should start each SCREW a few turns before completely tightening any of them. Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the right diagram. If it isn't, loosen the mounting screw to slide it against the stops. Then tighten the mounting screw. å Fasten a KNOB (69K) to the DOOR (G).
Step 13 å Refer to the enlarged diagram to identify the parts on the HINGES. å The DOORS may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal), turn the adjusting screw in or out. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws. Move the DOORS up or down to the desired location. Tighten the screws after making adjustments.
Step 14 VIEW THE T-SLOT BOX VIDEO å Pull the DRAWER FRONT BRACKETS (9G) apart and slide them into the grooves in the DRAWER SIDES (D50 and D51). You may need to gently tap them in with a hammer. å å å NOTE: The DRAWER FRONT BRACKETS are marked "RH" and "LH" for easy identification. Fasten the DRAWER FRONT (M) to the DRAWER FRONT BRACKETS (9G). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). Slide the DRAWER BOTTOM (D986) into the grooves in the DRAWER SIDES (D50 and D51) and DRAWER FRONT (M).
Step 15 å å VIEW THE T-SLOT BOX VIDEO Fasten the DRAWER BRACE (M65) to the DRAWER FRONT (M). Tighten one HIDDEN CAM. Fasten the DRAWER BACK (D80) to the DRAWER SIDES (D50 and D51) and DRAWER BRACE (M65). Use five BLACK 1-9/16" FLAT HEAD SCREWS (30S). 1 2 M65 Surface with HIDDEN CAM M Start each screw a few turns before completely tightening any of them. 30S BLACK 1-9/16" FLAT HEAD SCREW (5 used in this step) Be sure the DRAWER BOTTOM inserts into the DRAWER BACK groove. D80 D50 M65 D51 www.sauder.
Step 16 å å å VIEW THE DRAWER GLIDE VIDEO Fasten the DRAWER RIGHT (40DC) to the DRAWER RIGHT SIDE (D50) and the DRAWER LEFT (40DD) to the DRAWER LEFT SIDE (D51). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #2. Almost time to celebrate! With a nap. NOTE: The glides are not intended to rotate. Fasten the PULL (98K) to the DRAWER FRONT (M). Use two WASHERS (10I) and two SILVER 1/4" MACHINE SCREWS (61S).
Step 17 å Push the RUBBER SLEEVES (2R) over the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the ENDS (A2 and B2). Set the ADJUSTABLE SHELVES (H) onto the METAL PINS. å To insert the drawer into your unit, tip the front of the drawer down and drop the glides on the drawer behind the glides on the unit. Lift the front of the drawer up and slide it into the unit. å Apply the WARNING LABEL (11L) to the DRAWER BOTTOM (D986).
Step 18 å We recommend using the SAFETY BRACKET (1G) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (1S) into the top of the unit and a BLACK 2-1/4" FLAT HEAD SCREW (26S) into a stud in your wall. å å å Push a CAM COVER (13P) onto each visible HIDDEN CAM on the ENDS (A2 and B2. NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry.
Modèle 415995 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 8 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (10F) dans les gros trous des EXTRÉMITÉS (A2 et B2). Répéter cette étape pour le DESSOUS (D) et la TABLETTE (E). Fixer le DESSOUS (D) à l'EXTRÉMITÉ GAUCHE (B2). Serrer deux FIXATIONS TWIST-LOCK®.
ÉTAPE 13 ÉTAPE 17 Consulter le schéma agrandi pour identifier les pièces des CHARNIÈRES. Il faut peut-être ajuster les PORTES. Suivre les indications ci-dessous pour ajuster. RÉGLAGES DES PORTES : Pour ajuster les PORTES latéralement (horizontalement), tourner la vis de réglage vers l'intérieur ou vers l'extérieur. Pour ajuster les PORTES de haut en bas (verticalement), desserrer les deux vis de réglage. Déplacer les PORTES verticalement à l'emplacement désiré. Serrer les vis après avoir ajusté.
Armario Modelo 415995 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 7 No apriete los SUJETADORES TWIST-LOCK® en este paso. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (10F) dentro de los agujeros grandes de los EXTREMOS (A2 y B2). Repita este paso para el FONDO (D) y el ESTANTE (E). Fije el ESTANTE (E) al EXTREMO IZQUIERDO (B2). Apriete dos SUJETADORES TWIST-LOCK®.
PASO 13 PASO 17 Consulte el diagrama ampliado para identificar las piezas de las BISAGRAS. Las PUERTAS pueden requerir de ajustes. Siga el texto abajo para hacer los ajustes necesarios. AJUSTE DE LA PUERTA: Para ajustar las PUERTAS de un lado al otro (horizontalmente), gire el tornillo de ajuste hacia el interior o hacia el exterior. Para ajustar las PUERTAS hacia arriba o hacia abajo (vertical), afloje los dos tornillos de ajuste. Mueva las PUERTAS hacia arriba o hacia abajo a la ubicación deseada.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes sobrecargados. • Un riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones o estantes sobrecargados pueden romperse. • Nunca exceder los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
