sauder.com Knick-knack paddywhack, give your stuff a home. Storage Wall Cannery Bridge Collection | 416091 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification 2-3 Hardware Identification Assembly Steps Assembly Tools Required No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-22 Hammer Français 23-25 Español 26-28 Safety 29-30 Warranty Not actual size Skip the power trip. This time. 31 Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Now you know our ABCs. Part Identification F2 R Q M I K E A K E K L K Q K P M P K O B R C H2 D G2 L N J O T T www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push thirty HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHTS (C and D), LARGE UPRIGHTS (E), TOP (F2), BOTTOM (G2), and SHELF (H2). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM except in the ENDS (A and B) and LARGE UPRIGHTS (E).
Step 2 å Turn fourteen CAM SCREWS (8F) into the FRONTLEGS (L) and UPRIGHT MOLDINGS (P). Remember: Righty tighty. Lefty loosey. (14 used) 8F L L P P Page 6 416091 www.sauder.
Step 3 å Turn eight BLACK 9/16" FLAT HEAD SCREWS (32S) into the ENDS (A and B) until the shoulders of the SCREWS rest on the surfaces of the ENDS. å Slide the MOLDINGS (O and Q) onto the ENDS (A and B). Line up the grooves in the MOLDINGS over the heads of the SCREWS in the ENDS. å NOTE: The END MOLDINGS (O) are wider than the UPPER END MOLDINGS (Q). å NOTE: Be sure to place the MOLDINGS in the exact locations shown below. Q Edge with smaller holes These edges should be even.
Step 4 å Fasten the FRONT LEGS (L) to the ENDS (A and B). Tighten eight HIDDEN CAMS. å Fasten the REAR LEGS (M) to the ENDS (A and B). Use eight BLACK 2-3/4" FLAT HEAD SCREWS (100S). 100S BLACK 2-3/4" FLAT HEAD SCREW (8 used in this step) These surfaces should be even. L These surfaces should be even. S wi urfa HI th ce CA DD M EN S A M M This hole must be here. L S wi urfa H th ce CA IDD M EN S B Edge with larger holes This hole must be here. 1 Page 8 2 416091 www.sauder.
Step 5 å Fasten the TOP (F2) and SHELF (H2) to the LEFT END (B). Tighten four HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Notched edge L ith e w AMS c a f Sur DEN C D HI B Sur HIDface w DEN ith CA MS Sur HIDface w DEN itho CA ut MS F2 Notched edge H2 Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: www.
Step 6 å Slide the SHELF MOLDINGS (R) onto the notched edges of the TOP (F2) and SHELF (H2). å *U.S. Patent No. 5,499,886 Notched edge Slide the SHELF MOLDING (R) onto the notched edge. Notched edge F2 R H2 R Slide the SHELF MOLDING (R) onto the notched edge. Page 10 416091 www.sauder.
Step 7 å Fasten the LARGE UPRIGHTS (E) to the TOP (F2) and SHELF (H2). Use eight BLACK 1-15/16" FLAT HEAD SCREWS (113S). å Fasten the UPRIGHT MOLDINGS (P) to the LARGE UPRIGHTS (E). Tighten six HIDDEN CAMS. Edge with HIDDEN CAMS P P E ith e w AMS c a f Sur DEN C D HI E ith ew c a f Sur H2 F2 S AM C DEN HID 113S BLACK 1-15/16" FLAT HEAD SCREW (8 used in this step) 1 2 www.sauder.
Step 8 å Fasten the UPRIGHTS (C and D) to the SHELF (H2). Tighten four HIDDEN CAMS. Don't worry. It isn't Rome. This can be built in a day. Finished edge H2 D ith e w AMS c a f Sur DEN C HID C withMS e c fa A Sur DEN C HID Maximum 210 degrees Arrow Minimum 190 degrees Page 12 416091 www.sauder.
Step 9 å Fasten the BOTTOM (G2) to the LEFT END (B). Tighten two HIDDEN CAMS. å Fasten the BOTTOM (G2) to the UPRIGHTS (C and D). Use four BLACK 1-15/16" FLAT HEAD SCREWS (113S). å Push the DOOR STOPS (4I) into the holes in the UPRIGHTS (C and D). 4I These holes must be here. B Sur HIDface w DEN ith CA MS D C G2 4I 113S Maximum 210 degrees BLACK 1-15/16" FLAT HEAD SCREW (4 used in this step) Arrow Minimum 190 degrees www.sauder.
Step 10 å Fasten the RIGHT END (A) to the TOP (F2), BOTTOM (G2), and SHELF (H2). Tighten six HIDDEN CAMS. F2 L H2 G2 ut itho S w e fac CAM r u S DEN HID A Maximum 210 degrees Arrow Minimum 190 degrees Page 14 416091 www.sauder.
Step 11 å Fasten three METAL BRACKETS (4G) to the BOTTOM (G2). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the METAL BRACKETS are even with the edge of the BOTTOM. å Fasten two SAFETY BRACKETS (1G) to the ENDS (A and B). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). å å NOTE: Use the bottom holes in the SAFETY BRACKETS (1G). Fasten the BASE (N) to the ENDS (A and B) and BOTTOM (G2). Use five BLACK 9/16" LARGE HEAD SCREWS (1S) through the BRACKETS and into the BASE.
Step 12 å Carefully turn your unit over onto its front edges. Unfold the BACK (I) and lay it over your unit. å Make equal margins along all four edges of the BACK (I). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (I) to your unit using the NAILS (1N). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. NOTE: Be sure to tap NAILS into the holes that line up over the UPRIGHTS (C, D, and E) and SHELF (H2).
Step 13 å Fasten eight METAL BRACKETS (4G) to the SUPPORTS (S and T). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the METAL BRACKETS are even with the edges of the SUPPORTS. å Fasten the SIDE SUPPORTS (T) to the SUPPORT (S). Use two BLACK 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKETS and into the SUPPORT. å Fasten the SUPPORTS (S and T) to the BOTTOM (G2). Use six BLACK 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKETS and into the BOTTOM.
Step 14 å Fasten four CURVED HINGES (14H) to two of the DOORS (J). Use eight BLACK 1/2" FLAT HEAD SCREWS (11S). å Fasten two STRAIGHT HINGES (40H) to the remaining DOOR (J). Use four BLACK 1/2" FLAT HEAD SCREWS (11S). STRAIGHT HINGE 11S 40H BLACK 1/2" FLAT HEAD SCREW (12 used in this step) 14H J CURVED HINGE J J Page 18 416091 www.sauder.
Step 15 å å Carefully stand your unit upright. å First, fasten the DOOR (J) with STRAIGHT HINGES (40H) to the RIGHT UPRIGHT (C). Use the screws in the HINGES. You should start each SCREW a few turns before completely tightening any of them. å NOTE: Tighten the adjusting SCREWS completely in to center this DOOR between the UPRIGHTS. å Fasten a DOOR (J) with CURVED HINGES (14H) to the RIGHT END (A). Use the screws in the HINGES.
Step 16 å Refer to the enlarged diagram to identify the parts on the HINGES. å The DOORS may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal), loosen the mounting screw several turns, then turn the adjusting screw in or out. Tighten the mounting screw after making adjustments. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws.
Step 17 å We recommend using the SAFETY BRACKET (1G) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (1S) into the top of the unit and a BLACK 1-7/8" FLAT HEAD SCREW (2S) into a stud in your wall. BLACK 1-7/8" FLAT HEAD SCREW (1 used into a stud in your wall) 2S 1G BLACK 9/16" LARGE HEAD SCREW (1 used into the top of your unit) 1S www.sauder.
Step 18 å Push the RUBBER SLEEVES (2R) over the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B) and LARGE UPRIGHTS (E). Set the ADJUSTABLE SHELVES (K) onto the METAL PINS. å å Push a CAM COVER (36P) onto each visible HIDDEN CAM. å This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. NOTE: Please read the back pages of the instruction booklet for important safety information.
416091 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Enfiler les MOULURES DE TABLETTE (R) sur les chants crantés du DESSUS (F2) et de la TABLETTE (H2). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. * Brevet État Unis n° 5,499,886 Enfoncer trente EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A et B), les MONTANTS (C et D), les GRANDS MONTANTS (E), le DESSUS (F2), le DESSOUS (G2) et la TABLETTE (H2).
ÉTAPE 12 ÉTAPE 15 (SUITE) Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Fixer une PORTE (J) avec les CHARNIÈRES COURBÉES (14H) à l'EXTRÉMITÉ DROITE (A). Utiliser les vis fournies avec les CHARNIÈRES. Il est préférable de donner quelques tours de tournevis à chaque VIS avant de les serrer toutes à bloc. Avec précaution, retourner l'élément sur ses chants avant. Déplier l'ARRIÈRE (I) et le placer sur l'élément.
416091 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Deslice las MOLDURAS DE ESTANTE (R) sobre los bordes con muesca del PANEL SUPERIOR (F2) y del ESTANTE (H2). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje treinta EXCÉNTRICOS ESCONDIDOS (1F) dentro de los EXTREMOS (A y B), de los PARALES (C y D), de los PARALES GRANDES (E), del PANEL SUPERIOR (F2), del FONDO (G2) y del ESTANTE (H2).
PASO 12 PASO 15 (CONTINUACIÓN) Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Fije una PUERTA (J) con BISAGRAS CURVADAS (14H) al EXTREMO DERECHO (A). Utilice los tornillos provistos de las BISAGRAS. Debe apretar cada TORNILLO unas vueltas antes de apretar cualquier tornillo firmemente. Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Desdoble el DORSO (I) y colóquelo sobre la unidad.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes sobrecargados. • Un riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones o estantes sobrecargados pueden romperse. • Nunca exceder los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
