CONTACT US FIRST sauder.com BEFORE MAKING ANY RETURNS TO THE STORE. Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep. Prefer the phone? Give us a ring at 1-800-523-3987. Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays) WARNING CHOKING HAZARD - Small Parts Not for children under 3 years. Adult assembly required.
Table of Contents Part Identification Assembly Tools Required 2-3 Hardware Identification No. 2 Phillips Screwdriver Tip Shown Actual Size 4 Assembly Steps 5-18 Français 19-21 Español 22-24 Safety 25-26 Warranty Hammer Not actual size Skip the power trip. This time. 27 Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Part Identification C2 J A2 D F B2 G E I D36 D175 D982 D37 www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/service/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push fourteen HIDDEN CAMS (1F) into the ENDS (A2 and B2) and BRACES (E, F, and, M67). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step.
Step 2 VIEW THE DRAWER GLIDE VIDEO å Fasten the UNIVERSAL CABINET RAILS* (35AA) to the ENDS (A2 and B2 ). Use sixteen GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. å *patent pending glide system 3S GOLD 5/16" FLAT HEAD SCREW (16 used in this step) Glide end 1 2 3 Finished edge 1 withCAMS e c fa N Sur IDDE 3 H 2 1 2 A2 1 3 3 2 2 1 3 3 ith S e w CAM 2 c a N f Sur IDDE 1 H 3 2 B2 3 1 2 1 Glide end Finished edge Page 6 416407 www.sauder.
Step 3 Fasten four METAL BRACKETS (4G) to the BASE (I). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). å Remember: Righty tighty. Lefty loosey. 4G 1S BLACK 9/16" LARGE HEAD SCREW (4 used in this step) I 4G www.sauder.
Step 4 å Fasten the LEFT END (B2) to the TOP (C2). Tighten two HIDDEN CAMS. å Fasten the BACK BRACE (E) to the LEFT END (B2). Tighten two HIDDEN CAMS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Rounded edge Finished edge B2 face Sur withDEN HID S CAM C2 Sur fac ew ith hol es Sur E fac ew ith HID DEN CA MS These edges must be even. Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened.
Step 5 å å Insert two METAL PINS (1R) into the FRONT BRACE (F). å NOTE: Be sure the METAL PIN in the FRONT BRACE inserts into the hole in the LEFT END. å Fasten the RIGHT END (A2) to the TOP (C2) and BRACES (E and F). Tighten five HIDDEN CAMS. å NOTE: Be sure the METAL PIN in the FRONT BRACE inserts into the hole in the RIGHT END. Maximum 210 degrees Fasten the FRONT BRACE (F) to the LEFT END (B2). Tighten the HIDDEN CAM.
Step 6 å Fasten the TOP MOLDING (J) to the TOP (C2). Use three SILVER 1-1/8" FLAT HEAD SCREWS (10S). å å NOTE: Do not overtighten the SCREWS into the TOP. Curved edge Fasten the BASE (I) to the ENDS (A2 and B2). Use four BLACK 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKETS on the BASE and into the ENDS. 10S SILVER 1-1/8" FLAT HEAD SCREW (3 used for the TOP MOLDING) J B2 C2 I A2 Curved edge 1S BLACK 9/16" LARGE HEAD SCREW (4 used for the BASE) Page 10 416407 www.sauder.
Step 7 å Fasten the BRACE (G) to the BACK BRACE (E). Use two BLACK 1-1/4" FLAT HEAD SCREWS (7S). Now might be a good time to refresh your drink. 7S BLACK 1-1/4" FLAT HEAD SCREW (2 used in this step) G E www.sauder.
Step 8 å Carefully turn your unit over onto its front edges. Unfold the BACK (D) and lay it over your unit. å Make equal margins along all four edges of the BACK (D). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (D) to your unit using the NAILS (1N). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Using your hammer, gently tap six TACK GLIDES (13E) into the ENDS (A2 and B2) and BASE (I). 1N This hole must be here.
Step 9 å Fasten the DRAWER SIDES (D36 and D37) to the DRAWER BACK (D175). Use four BLACK 1-9/16" FLAT HEAD SCREWS (30S). å Slide the DRAWER BOTTOM (D982) into the grooves in the DRAWER SIDES (D36 and D37) and DRAWER BACK (D175). å Repeat this step for the other drawers. Be sure the grooves in each part line up with each other on the inside of the drawer. D37 D175 Groove D36 30S BLACK 1-9/16" FLAT HEAD SCREW (16 used in this step) These edges should be even.
Step 10 å Pull the DRAWER FRONT BRACKETS (9G) apart and slide them into the grooves in the DRAWER SIDES (D36 and D37). å Fasten the DRAWER FRONT (H) to the DRAWER FRONT BRACKETS (9G). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). å Repeat this step for the other drawers. Push down 1S 9G BLACK 9/16" LARGE HEAD SCREW (16 used in this step) D37 D36 H Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Page 14 416407 www.sauder.
Step 11 å Turn the drawer over and fasten the DRAWER BRACE (M67) to the DRAWER FRONT (H). Tighten a HIDDEN CAM. å Fasten the DRAWER BRACE (M67) to the DRAWER BACK (D175). Use a BLACK 1-9/16" FLAT HEAD SCREW (30S). å Repeat this step for the other drawers. Maximum 210 degrees Arrow Minimum 190 degrees Hidden part using recycled material. Color may vary. Surface with HIDDEN CAM M67 D175 H 30S BLACK 1-9/16" FLAT HEAD SCREW (4 used in this step) www.sauder.
Step 12 VIEW THE DRAWER GLIDE VIDEO å Fasten a DRAWER RIGHT (35AC) to the RIGHT DRAWER SIDE (D36) and a DRAWER LEFT (35AD) to the LEFT DRAWER SIDE (D37). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #2. å å NOTE: The glides are not intended to rotate. å Repeat this step for the other drawers. Now, fasten a KNOB (91K) to the DRAWER FRONT (H). Use a BLACK 1-1/8" PAN HEAD SCREW (9S).
Step 13 å å å Carefully stand your unit upright in its final location. We recommend using the SAFETY STRAP for added stability. Open the FURNITURE TIPPING RESTRAINT KIT (97). å INSTALLATION INSTRUCTIONS: 1. Insert the SAFETY DRYWALL ANCHOR through the WASHER and one end of the SAFETY STRAP. 2. Using a Phillips screwdriver or a hand drill, press the screw slightly onto the drywall. 3. Apply pressure; turn the screw until a pilot hole is made and the nylon sheath slips through. 4.
Step 14 å To insert the drawers into your unit, tip the front of the drawers down and drop the glides on the drawers behind the glides on the unit. Lift the front of the drawers up and slide them into the unit. å å NOTE: Be sure the label on the LEFT DRAWER SIDE is in the UPPER drawer. å å NOTE: Please read the back pages of the instruction booklet for important safety information.
Modèle 416407 Commode 4 Tiroirs Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Fixer la MOULURE DE DESSUS (J) au DESSUS (C2). Utiliser trois VIS TÊTE PLATE 28 mm ARGENTÉES (10S). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. REMARQUE : Ne pas trop serrer les VIS dans le DESSUS. Enfoncer quatorze EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A2 et B2) et les ENTRETOISES (E, F et M67).
ÉTAPE 11 ÉTAPE 13 (SUITE) Retourner le tiroir et fixer l’ENTRETOISE DE TIROIR (M67) au DEVANT DE TIROIR (H). Serrer un EXCENTRIQUE ESCAMOTABLE. Avec précaution, découper le trou pré-percé dans l’ARRIÈRE (D). Insérer l’autre extrémité de la SANGLE DE SÉCURITÉ à travers ce trou, puis utiliser une VIS TÊTE LARGE NOIRE 14 mm à travers la SANGLE DE SÉCURITÉ et dans le trou pré-percé sur le dessous du DESSUS (C2). Fixer l'ENTRETOISE DE TIROIR (M67) à l'ARRIÈRE DE TIROIR (D175).
Modelo 416407 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Fije la MOLDURA DE PANEL SUPERIOR (J) al PANEL SUPERIOR (C2). Utilice tres TORNILLOS PLATEADOS DE CABEZA PERDIDA de 28 mm (10S). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje catorce EXCÉNTRICOS ESCONDIDOS (1F) en los EXTREMOS (A2 y B2) y las RIOSTRAS (E, F y M67).
PASO 11 PASO 13 (CONTINUACIÓN) Da vuelta al cajón y apriete la RIOSTRA DE CAJÓN (M67) a la CARA DE CAJÓN (H). Apriete un EXCÉNTRICO ESCONDIDO. Cuidadosamente corte el agujero perforado del DORSO (D). Inserte el otro extremo de la CORREA DE SEGURIDAD a través de este agujero, luego use un TORNILLO NEGRO DE CABEZA GRANDE de 14 mm a través de la CORREA DE SEGURIDAD y en el agujero pre-perforado en el fondo del PANEL SUPERIOR (C2). Fije la RIOSTRA DE CAJÓN (M67) al DORSO DE CAJÓN (D175).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following safety information. Death or serious injury may occur when children climb on furniture. A remote control, toys or other items placed on the furniture may encourage a child to climb on the furniture which could cause it to tip-over and result in serious injury or death. NEVER allow children to climb on furniture.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Lea cuidadosamente la siguiente información de seguridad. Pueden suceder lesiones graves o la muerte cuando los niños se suben en los muebles. Un control remoto, juguetes u otros artículos colocados en los muebles pueden alentar a un niño a subirse en el mueble, lo cual podría causar que se derribe y resultaría en lesiones graves o la muerte.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
If you need assistance please contact customer service at 800-523-3987 Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays) or at sauder.com/service. Register your new product online For immediate service, 24 hours per day, 7 days per week, to order replacement parts, access assembly tips and register your product, visit www.sauder.com/service So, how did it go? Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.