sauder.com Your holder for all things awesome. Display Cabinet Dakota Pass Collection | 418268 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-20 Français pg 21-24 Español pg 25-28 Lot # 365798 10/14/14 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-20 Hammer Français 21-24 Español 25-28 Safety 29-30 Warranty Not actual size Skip the power trip. This time. 31 ! WARNING Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or death.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 34E ADJUSTABLE FOOT - 1 14H HINGE - 4 4I 1F HIDDEN CAM - 10 8F DOOR STOP - 2 10F CAM SCREW - 10 28K KNOB- 2 1L TWIST-LOCK® FASTENER - 10 WARNING LABEL - 1 17F MOLDING CONNECTOR - 2 3M ANTI-SKID PAD - 1 WARNING Never use this furniture with a TV that is too large or too heavy. Severe injury or death can occur. The TV and furniture will be unstable and may tip. -The TV must less than 50 lbs.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (10F) into the large holes in the ENDS (A and B). å Repeat this step for the UPRIGHT (C) and BOTTOM (E). Scan this QR code or go to this address: http://qr.sauder.com/?ID=1420 to watch a video on how to assemble your unit.
Step 2 å Turn ten CAM SCREWS (8F) into the FRONT LEGS (I and J) and TOP MOLDING (L). å Push ten HIDDEN CAMS (1F) into the ENDS (A and B) and TOP (D). (10 used) 8F J L I Arrow 1F (10 used) D B A Arrow Arrow Hole 1F The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. Page 6 418268 www.sauder.
Step 3 å Fasten the LEFT END (B) and UPRIGHT (C) to the TOP (D). Tighten four TWIST-LOCK® FASTENERS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible.
Step 4 å Fasten the BOTTOM (E) to the LEFT END (B). Tighten two TWIST-LOCK® FASTENERS. å Fasten the BOTTOM (E) to the UPRIGHT (C). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). å Fasten the FOOT (34E) to the BOTTOM (E). Use a BLACK 1-7/8" FLAT HEAD SCREW (2S) through the FOOT and into the UPRIGHT (C) and three BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Adjustments will be made to the ADJUSTABLE FOOT after the unit is standing upright and in its final location. Remember: Righty tighty. Lefty loosey.
Step 5 å Fasten the RIGHT END (A) to the TOP (D) and BOTTOM (E). Tighten four TWIST-LOCK® FASTENERS. å Slide the BOTTOM MOLDING* (O) onto the notched edge of the BOTTOM (E). å Insert two DOOR STOPS (4I) into the holes in the UPRIGHT (C). å *U.S. Patent No. 5,499,886 Notched edge E Slide the BOTTOM MOLDING (O) onto the notched edge. C O A D 4I Edge with HIDDEN CAMS www.sauder.
Step 6 Tap two MOLDING CONNECTORS (17F) into the notches in the FRONT LEGS (I and J) and TOP MOLDING (L). å Use your hammer to tap the MOLDING CONNECTOR (17F) into the notches in the MOLDINGS Flat end Flat end 17F 17F J I L Page 10 418268 www.sauder.
Step 7 å Fasten the FRONT LEGS (I and J) and TOP MOLDING (L) to the ENDS (A and B) and TOP (D). Tighten ten HIDDEN CAMS. å NOTE: Be careful in handling the FRONT LEGS/TOP MOLDING assembly until it is fastened to your unit. 1 2 B J D A I L www.sauder.
Step 8 å å Carefully turn your unit over onto its front edges. Fasten the BACK LEGS (K) to the ENDS (A and B). Use six BLACK 2-1/4" FLAT HEAD SCREWS (26S). Don't worry. It isn't Rome. This can be built in a day. 26S BLACK 2-1/4" FLAT HEAD SCREW (6 used in this step) Flat edge K Flat edge A K B Page 12 418268 www.sauder.
Step 9 å å Unfold the BACK (F) and lay it over your unit. å Make equal margins along all four edges of the BACK (F). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (F) to your unit using the NAILS (1N). Caution NOTE: Be sure to position the perforations in the BACK as shown. Do not stand the unit upright without the BACK fastened. The unit may collapse. NOTE: Perforations have been provided for access through the BACK. Carefully cut out the holes needed.
Step 10 å Fasten two HINGES (14H) to each DOOR (G). Use eight BLACK 1/2" FLAT HEAD SCREWS (11S). 11S BLACK 1/2” FLAT HEAD SCREW (8 used in this step) 14H G G 14H Page 14 418268 www.sauder.
Step 11 å å Carefully stand your unit upright. å Fasten the DOOR (G) to the LEFT END (B) as shown in the lower diagram. Use the screws in the HINGES. You should start each SCREW a few turns before completely tightening any of them. Pro Tip: Lift with your legs. And, you know, your arms. Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the right diagram. If it isn't, loosen the mounting screw to slide it against the stops.
Step 12 å Refer to the enlarged diagram to identify the parts on the HINGES. å The DOORS may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal), loosen the mounting screw several turns, then turn the adjusting screw in or out. Tighten the mounting screw after making adjustments. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws.
Step 13 å å Slide an ADJUSTABLE SHELF MOLDING* (N) onto the notched edge of the ADJUSTABLE SHELF (H). å å å Separate a CARD on the CARD SHEET (38M) and insert into the CARD HOLDER. Then, fasten a CARD HOLDER (35M) to the ADJUSTABLE SHELF MOLDING (N). Use two SILVER 5/8" MACHINE SCREWS (15S). Repeat this step for the other ADJUSTABLE SHELF (H). *U.S. Patent No. 5,499,886 H Notched edge N Slide the ADJUSTABLE SHELF MOLDING (N) onto the notched edge.
Step 14 å Push the RUBBER SLEEVES (2R) over the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B) and UPRIGHT (C). Set the ADJUSTABLE SHELVES (H) onto the METAL PINS. B H C H A 1R (8 used) Page 18 2R 418268 www.sauder.
Step 15 å å Position your unit in its final location. å å IMPORTANT: The ADJUSTABLE FOOT should not extend beyond the bottom edges of the FRONT LEGS (I and J). Using your screwdriver through the hole in the BOTTOM (E), turn the ADJUSTABLE FOOT (34E) downward until the FOOT touches the floor. Now, insert a HOLE PLUG (41P) into the hole in the BOTTOM (E). I E J With your No. 2 Phillips Screwdriver, turn the ADJUSTABLE FOOT downward until the FOOT touches the floor. 41P Floor 34E www.sauder.
Step 16 å Apply the WARNING LABEL (1L) to the TOP (D). You should be able to read the label when the TV is removed from the unit. When the TV is in place, it should hide the label. Peel off the backing and apply the label as shown in the diagram. å å å NOTE: This is a permanent label intended to last for the life of the product. Once applied, do not try to remove it. å å NOTE: Please read the back pages of the instruction booklet for important safety information.
418268 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
AVERTISSEMENT ÉTAPE 3 L'utilisation d'un téléviseur trop lourd ou trop gros est dangereuse. Un téléviseur trop lourd créera un risque de basculement pouvant provoquer de graves blessures ou la mort. Un téléviseur trop gros pour l'espace disponible risque d'être accidentellement poussé ou de tomber du mobilier ou d'être sujet à basculer. Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer.
ÉTAPE 7 ÉTAPE 11 Fixer les PIEDS AVANT (I et J) et la MOULURE SUPÉRIEURE (L) aux EXTRÉMITÉS (A et B) et au DESSUS (D). Serrer dix EXCENTRIQUES ESCAMOTABLES. Relever, avec précaution, l'élément dans sa position verticale. REMARQUE : Faire preuve de prudence pour manipuler l’assemblage PIEDS AVANT/MOULURE SUPÉRIEURE jusqu’à ce qu’il soit fixé sur l’unité. ÉTAPE 8 Avec précaution, retourner l'élément sur ses chants avant. Fixer les PIEDS ARRIÈRE (K) aux EXTRÉMITÉS (A et B).
ÉTAPE 13 ÉTAPE 15 Enfiler la MOULURE DE TABLETTE RÉGLABLE* (N) sur le chant cranté de la TABLETTE RÉGLABLE (H). Placer l'élément dans son emplacement final. Ensuite, fixer une PORTE-CARTES (35M) sur la MOULURE DE TABLETTE RÉGLABLE (N). Utiliser deux VIS À MÉTAUX 16 mm ARGENTÉES (15S). Séparer une CARTE de la FICHE DE CARTES (38M) et l’insérer dans le PORTE-CARTES. Répéter cette étape pour l'autre TABLETTE RÉGLABLE (H).
418268 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
ADVERTENCIA PASO 3 El uso de un televisor demasiado pesado o grande es peligroso. Un televisor demasiado pesado generará riesgo de caída, lo cual podría causar lesiones graves o muerte. Un televisor demasiado grande para el espacio disponible puede ser empujado o golpeado por accidente, causando que éste se salga del mueble o se caiga. Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. • Verifique el tamaño y peso del televisor.
PASO 7 PASO 11 Fije las PATAS DELANTERAS (I y J) y la MOLDURA SUPERIOR (L) a los EXTREMOS (A y B) y al PANEL SUPERIOR (D). Apriete diez EXCÉNTRICOS ESCONDIDOS. Cuidadosamente ponga la unidad en posición vertical. NOTA: Tenga cuidado con las PATAS DELANTERAS / MOLDURA SUPERIOR hasta que esté completamente fijada a la unidad. Antes de ajustar la PUERTA a su unidad, asegúrese de que el tornillo de montaje se encuentre contra los topes como se muestra en el diagrama derecho.
PASO 13 PASO 15 Deslice una MOLDURA DE ESTANTE AJUSTABLE* (N) sobre el borde con muesca del ESTANTE AJUSTABLE (H). Coloque su unidad en su posición final. A continuación, fije el PORTA-TARJETAS (35M) a la MOLDURA DEL ESTANTE AJUSTABLE (N). Utilice dos TORNILLOS PLATEADOS PARA METAL de 16 mm (15S). Separe una TARJETA en la HOJA DE TARJETAS (38M) e inserte en el PORTA-TARJETAS. Repita este paso para el otro ESTANTE AJUSTABLE (H).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Children climbing on furniture. • A child may try to reach a toy or other object by climbing on furniture. • Children will play and be active near the TV. • Risk of injury or death.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Los niños subiendo al mobiliario. • El niño que intenta a alcanzar un juego u otro objeto subiendo al mobiliario. • Los niños jugarán y estarán activos cerca del televisor. • Riesgo de lesiones o la muerte.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
