sauder.com For things 'n such. Hutch Barrister Lane Collection | 418295 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-17 Français pg 18-19 Español pg 20-21 Lot # 366595 11/25/14 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-17 Hammer Français 18-19 Español 20-21 Not actual size Short Screwdriver Safety 22 Warranty 23 Page 2 Skip the power trip. This time. 418295 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. A RIGHT END (1) E SHELF (1) I SKIRT (1) B LEFT END (1) F RIGHT BACK (1) J FRONT MOLDING (1) C UPRIGHT (1) G LEFT BACK (1) K RIGHT MOLDING (1) D TOP (1) H DIVIDER (3) L LEFT MOLDING (1) K D J F L H A H G H C E I B www.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 1F HIDDEN CAM - 12 2F CAM DOWEL - 12 17F MOLDING CONNECTOR - 2 1N NAIL - 36 36P CAM COVER - 10 1R METAL PIN - 11 1S BLACK 9/16" LARGE HEAD SCREW - 3 7S BLACK 1-1/4" FLAT HEAD SCREW - 9 Page 4 2S 418295 BLACK 1-7/8" FLAT HEAD SCREW - 3 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push twelve HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHT (C), SHELF (E), and SKIRT (I). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step.
Step 2 å Tap two MOLDING CONNECTORS (17F) into the notches in the MOLDINGS (J, K, and L). Use your hammer to tap the MOLDING CONNECTOR (17F) into the notches in the MOLDINGS. Flat end Flat end 17F 17F L J Page 6 418295 K www.sauder.
Step 3 å Turn the MOLDINGS (J, K, and L) over and fasten them to the TOP (D). Use nine BLACK 1-1/4" FLAT HEAD SCREWS (7S). Remember: Righty tighty. Lefty loosey. Finished surface 7S K BLACK 1-1/4" FLAT HEAD SCREW (9 used in this step) J Finished surface S ur fa ce L w ith h ol es D Rounded edge www.sauder.
Step 4 å Fasten the RIGHT END (A) to the RIGHT MOLDING (K). Tighten two HIDDEN CAMS. Curved edge Sur HIDface w DEN ith CA MS A Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. K J Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: Page 8 Start Tighten Arrow Maximum 210 degrees Arrow Minimum 190 degrees 418295 www.sauder.
Step 5 å Insert three METAL PINS (1R) into the holes shown in the TOP (D). å Slide the DIVIDERS (H) onto the METAL PINS (1R) in the TOP (D). å Now, insert six METAL PINS (1R) into the other end of the DIVIDERS (H). 1R H All curved edges should face the FRONT MOLDING (J). H H J 1R D www.sauder.
Step 6 å Fasten the SHELF (E) to the RIGHT END (A). Tighten two HIDDEN CAMS. å NOTE: Be sure the METAL PINS in the DIVIDERS (H) insert into the holes in the SHELF. Maximum 210 degrees Arrow Minimum 190 degrees Finished edge S H urf ID a D ce E w N i C th A M S E A H H H Page 10 418295 www.sauder.
Step 7 å Using your short screwdriver, fasten the UPRIGHT (C) to the TOP (D) and SHELF (E). Tighten four HIDDEN CAMS. Don't worry. It isn't Rome. This can be built in a day. Curved edge E D C Surface with HIDDEN CAMS Maximum 210 degrees Arrow Minimum 190 degrees www.sauder.
Step 8 å å Insert a METAL PIN (1R) into the UPRIGHT (C). å NOTE: Be sure the METAL PIN in the UPRIGHT inserts into the SKIRT. Fasten the SKIRT (I) to the UPRIGHT (C). Tighten one HIDDEN CAM. Curved edge 1R I Surface with holes C Maximum 210 degrees Arrow Minimum 190 degrees Page 12 418295 www.sauder.
Step 9 å å Insert a METAL PIN (1R) into the LEFT END (B). å NOTE: Be sure the METAL PIN in the LEFT END inserts into the SKIRT. Fasten the LEFT END (B) to the LEFT MOLDING (L) and SKIRT (I). Tighten three HIDDEN CAMS. 1R Maximum 210 degrees Arrow Minimum 190 degrees Curved edge B L I Surface with HIDDEN CAMS www.sauder.
Step 10 å Push a CAM COVER (36P) onto each visible HIDDEN CAM in the ENDS (A and B), UPRIGHT (C), and SHELF (E). Hey! It's starting to look like something! B E C A 36P (10 used) To cover HIDDEN CAMS Page 14 418295 www.sauder.
Step 11 å Carefully turn your unit over onto its front edges. Unfold the RIGHT BACK (F) and lay it over your unit. å Make equal margins along the top and outer side edge of the RIGHT BACK (F). Push on opposite corners of your unit if needed to make it “square”. å Fasten the RIGHT BACK (F) to your unit using fourteen NAILS (1N). å NOTE: Be sure to tap NAILS into the holes that line up over the SHELF (E). å NOTE: Perforations have been provided for access through the RIGHT BACK.
Step 12 å å Unfold the LEFT BACK (G) and lay it over your unit. å NOTE: The LEFT BACK (G) will overlap the RIGHT BACK (F). Follow the enlarged diagram. å Fasten the LEFT BACK (G) to your unit using three BLACK 9/16" LARGE HEAD SCREWS (1S) into the holes shown in the LEFT BACK. Use fifteen NAILS (1N) into the top and both side edges. Caution Make equal margins along the top and outer edge of the LEFT BACK (G). Push on opposite corners of your unit if needed to make it “square”.
Step 13 å å Carefully stand your unit upright. å NOTE: Please read the back pages of the instruction booklet for important safety information. å This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. The instructions for fastening your unit to the 418294 Computer Desk is in the Computer Desk assembly manual. You will use seven NAILS (1N) and three BLACK 1-7/8" FLAT HEAD SCREWS (2S) from your Hutch hardware to fasten to the Computer Desk.
418295 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 9 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Insérer une GOUPILLE EN MÉTAL (1R) dans l'EXTRÉMITÉ GAUCHE (B). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Fixer l'EXTRÉMITÉ GAUCHE (B) à la MOULURE GAUCHE (L) et PLINTHE (I). Serrer trois EXCENTRIQUES ESCAMOTABLES. Enfoncer douze EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A et B), le MONTANT (C), la TABLETTE (E) et la PLINTHE (I).
418295 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 9 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Inserte una ESPIGA DE METAL (1R) dentro del EXTREMO IZQUIERDO (B). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Fije el EXTREMO IZQUIERDO (B) a la MOLDURA IZQUIERDA (L) y al FALDÓN (I). Apriete tres EXCÉNTRICOS ESCONDIDOS. Empuje doce EXCÉNTRICOS ESCONDIDOS (1F) dentro de los EXTREMOS (A y B), el PARAL (C), el ESTANTE (E) y el FALDÓN (I).
CAUTION Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. • Risk of injury. • Overloaded shelves can break. • Never exceed the weight limits shown in the instructions. • Improperly moving furniture that is not designed and equipped with casters. • Furniture can tip over or break if improperly moved.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.