sauder.com It stands. You sleep. Night Stand Cannery Bridge Collection | 419069 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-17 Français pg 18-20 Español pg 21-23 Lot # 376639 09/21/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-17 Hammer Français 18-20 Español 21-23 Safety 24-26 Warranty Page 2 Not actual size Skip the power trip. This time. 27 419069 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (10F) into the large holes in the ENDS (A and B) and BOTTOM (D). Do not tighten the TWIST-LOCK® FASTENERS in this step. 10F A B D 10F www.sauder.
Step 2 å Push six HIDDEN CAMS (1F) into the ENDS (A and B). Do not tighten the HIDDEN CAMS in this step. Arrow A Su TW rfa FA IS ce w ST T-L ith EN OC ER K® S Su TW rfa FA IS ce w ST T-L ith EN OC ER K® S 1F B Arrow 1F Arrow Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. Page 6 419069 www.sauder.
Step 3 å å å Turn six CAM SCREWS (8F) into the FRONT LEGS (F). NOTE: Position the LEGS exactly as shown. NOTE: Use the exact holes shown. 8F (6 used) NOTE: Use the exact holes shown. F F www.sauder.
Step 4 å Fasten the FRONT LEGS (F) to the ENDS (A and B). Tighten six HIDDEN CAMS. 1 2 These edges must be even. These surfaces should be even. Edge with TWIST-LOCK® FASTENERS Su TW rfa FA IS ce w ST T-L ith EN OC ER K® S F These edges must be even. Su TW rfa FA IS ce w ST T-L ith EN OC ER K® S A B F These surfaces should be even. F A Page 8 419069 www.sauder.
Step 5 å å Fasten the BACK LEGS (G) to the ENDS (A and B). Use six BLACK 2-1/4" FLAT HEAD SCREWS (26S). Don't worry. It isn't Rome. This can be built in a day. NOTE: Use the exact holes shown in the BACK LEGS. 26S These edges must be even. BLACK 2-1/4" FLAT HEAD SCREW (6 used for the BACK LEGS) Su TW rfa FA IS ce w ST T-L ith EN OC ER K® S F These edges must be even. A G G Su TW rfa FA IS ce w ST T-L ith EN OC ER K® S These surfaces should be even. B F These surfaces should be even. www.
Step 6 å Fasten the UNIVERSAL CABINET RAILS* (35AA) to the ENDS (A and B). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. å *patent pending glide system 3S GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Glide end 1 2 3 F A 3 2 1 B Glide end Page 10 F 419069 www.sauder.
Step 7 å Fasten the LEFT END (B) to the TOP (C) and BOTTOM (D). Tighten four TWIST-LOCK® FASTENERS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Su rfa ce wit hh ole s F C B These edges should be even. D Sur f TW ace wi IS th FAS T-LO TEN CK® ERS Notched edge Dowel end How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part.
Step 8 å Slide the BOTTOM MOLDING* (J) onto the notched edge of the BOTTOM (D). å Fasten the RIGHT END (A) to the TOP (C) and BOTTOM (D). Tighten four TWIST-LOCK® FASTENERS. å *U.S. Patent No. 5,499,886 Notched edge C J D F Slide the BOTTOM MOLDING (J) onto the notched edge. A ut itho w e ® fac CK Sur T-LO S IS TW TENER FAS Groove Page 12 419069 www.sauder.
Step 9 å Carefully turn your unit over onto its front edges. Unfold the BACK (E) and lay it over your unit. å Make equal margins along the top and side edges of the BACK (E). Push on opposite corners of your unit if needed to make it "square". å NOTE: Be sure the bottom row of holes line up over the BOTTOM (D). å NOTE: The bottom edge of the BACK will overhang the bottom of the unit. å å Fasten the BACK (E) to your unit using the NAILS (1N).
Step 10 VIEW THE T-LOCK BOX VIDEO 1 The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. 2 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. Un fi su nish rfa ed ce D964 D12 D12 D13 Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Groove å Insert the DRAWER SIDES (D12 and D13) at an angle into the slot at each end of the DRAWER FRONT (H).
Step 11 å å Insert a SLIDE CAM (10A) into the DRAWER SIDES (D12 and D13). å å å å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. Fasten a DRAWER RIGHT (35AC) to the DRAWER RIGHT SIDE (D12) and a DRAWER LEFT (35AD) to the DRAWER LEFT SIDE (D13). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #2. NOTE: The parts are marked "DRAWER RIGHT" and "DRAWER LEFT" for easy identification. NOTE: The glides are not intended to rotate.
Step 12 å å Carefully stand your unit upright. å Push a CAM COVER (12P) onto each visible HIDDEN CAM. Pro Tip: Lift with your legs. And, you know, your arms. To insert the drawer into your unit, tip the front of the drawer down and drop the glides on the drawer behind the glides on the unit. Lift the front of the drawer up and slide it into the unit. 30 lbs. 15 lbs. 25 lbs. 12P (6 used) To cover HIDDEN CAMS Page 16 419069 www.sauder.
Step 13 å To make adjustments to the drawer, loosen SCREW #2 in the SLIDES a 1/4 turn, then turn the CAM clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. By adjusting the drawer this way, it will help the DRAWER FRONT line up better when closed. Tighten the SCREW when finished with adjustments.
419069 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Fixer les GLISSIÈRES D'ÉLÉMENT UNIVERSELLES* (35AA) aux EXTRÉMITÉS (A et B). Utiliser quatre VIS TÊTE PLATE 8 mm DORÉES (3S) à travers les trous n° 1 et le n° 3. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (10F) dans les gros trous des EXTRÉMITÉS (A et B) et le DESSOUS (D).
ÉTAPE 9 ÉTAPE 11 Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Insérer une EXCENTRIQUE DE COULISSE (10A) dans les CÔTÉS DE TIROIR (D12 et D13). Avec précaution, retourner l'élément sur ses chants avant. Déplier l'ARRIÈRE (E) et le placer sur l'élément. Fixer un TIROIR DROIT (35AC) sur le CÔTÉ DROIT DE TIROIR (D12) et un TIROIR GAUCHE (35AD) sur le CÔTÉ GAUCHE DE TIROIR (D13).
419069 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 No apriete los SUJETADORES TWIST-LOCK® en este paso. Fije los RIELES UNIVERSALES DE GABINETE* (35AA) a los EXTREMOS (A y B). Utilice cuatro TORNILLOS DORADOS DE CABEZA PLANA de 8 mm (3S) a través de los agujeros No. 1 y No. 3. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (10F) dentro de los agujeros grandes de los EXTREMOS (A y B) y del FONDO (D).
PASO 9 PASO 11 Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Insertar un EXCÉNTRICO DE CORREDERA (10A) en los LADOS DE CAJÓN (D12 y D13). Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Desdoble el DORSO (E) y colóquelo sobre la unidad. El margen a lo largo de los bordes superior y laterales del DORSO (E) debe estar uniforme. Empuje sobre las esquinas opuestas de la unidad si es requerido para hacerla "cuadrada.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded drawers and shelves. • Risk of injury. • Never exceed the weight limits shown in • Top-heavy furniture can tip over. the instructions. • Overloaded drawers or shelves can break. • Work from bottom to top when loading shelves and drawers.
AVERTISSEMENT Prière d’utiliser le mobilier à bon escient et avec prudence. Une mauvaise utilisation peut être à l’origine de risques d’accident ou peut endommager le mobilier et les articles ménagers. Lire attentivement le tableau suivant. À surveiller : Danger éventuel : Solution : • Tiroirs et tablettes surchargées. • Risque de blessure. • Du mobilier mal équilibré risque de se renverser. • Des tiroirs surchargés peuvent casser.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • El sobrecargo de cajones y estantes. • Un riesgo de lesiones. • La caída de mobiliario inestable. • La rotura de cajones sobrecargados. • Nunca exceda los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
