sauder.com Guaranteed to hold other beverages, too. Lift-Top Coffee Table Carson Forge Collection | Model 420421 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification 2-3 Hardware Identification Assembly Steps Assembly Tools Required No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-23 Hammer Français 24-26 Español 27-29 Safety 30 Warranty 31 Not actual size Skip the power trip. This time. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Now you know our ABCs. Part Identification D L M J I K B F H G F K L C H A E I M N N N www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push twenty-four HIDDEN CAMS (1F) into the ENDS (A and B), BOTTOM (E), PANELS (F), and SHELF (G). Then, insert the metal end of eight CAM DOWELS (2F) into the HIDDEN CAMS in the BOTTOM (E) and SHELF (G). Do not tighten the HIDDEN CAMS in this step.
Step 2 å Turn sixteen CAM SCREWS (8F) into the LEGS (H and I). 8F (16 used) 8F 8F I I H H Page 6 420421 www.sauder.
Step 3 å Fasten a CORNER ACCENT (87M) to each LEG (H and I). Use four SILVER 1/2" MACHINE SCREWS (38S). 38S SILVER 1/2" MACHINE SCREW (4 used in this step) I 87M I 87M H 87M H 87M www.sauder.
Step 4 å Fasten the REAR LEGS (H and I) to the ENDS (A and B). Tighten six HIDDEN CAMS. 1 2 These edges should be even. Angled edge H S HI urfa DD ce EN wi CA th M S A These edges should be even. S HI urfa DD ce EN wi CA th M S B I Angled edge Page 8 420421 www.sauder.
Step 5 å å Carefully turn your ENDS (A and B) over. å Slide the END MOLDINGS (L and M) onto the ENDS (A and B) until they are against the LEGS (H and I). Line up the grooves in the MOLDINGS over the heads of the SCREWS in the ENDS. Turn eight BLACK 9/16" FLAT HEAD SCREWS (32S) into the ENDS (A and B) until the shoulders of the SCREWS rest on the surfaces of the ENDS.
Step 6 å å Carefully turn your ENDS (A and B) over. Fasten the remaining LEGS (H and I) to the ENDS (A and B). Tighten six HIDDEN CAMS. 1 2 These edges should be even. These edges should be even. S HI urfa DD ce EN wi CA th M S A I H Angled edge S HI urfa DD ce EN wi CA th M S B Page 10 Angled edge 420421 www.sauder.
Step 7 å Turn six BLACK 9/16" FLAT HEAD SCREWS (32S) into the PANELS (F) until the shoulders of the SCREWS rest on the surfaces of the PANELS. 32S å Slide the PANEL MOLDINGS (K) onto the PANELS (F). Line up the grooves in the MOLDINGS over the heads of the SCREWS in the PANELS. å Then, fasten the SHELF (G) to the PANELS (F). Use six BLACK 1-7/8" FLAT HEAD SCREWS (2S).
Step 8 å Fasten the PANELS (F) and SHELF (G) to the LEFT END (B) and LEGS (H and I). Tighten four HIDDEN CAMS. H B Sur f a HID ce w DEN ith CA MS F I G ith e w AMS c a f Sur DEN C HID F Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: Page 12 Start Tighten Arrow Maximum 210 degrees Arrow Minimum 190 degrees 420421 www.sauder.
Step 9 å å Insert two METAL PINS (1R) into the larger holes in the UPRIGHT (C). Insert the METAL PINS (1R) in the end of the UPRIGHT (C) into the holes in the SHELF (G). G C 1R www.sauder.
Step 10 å Fasten the BOTTOM (E) to the LEFT END (B). Tighten two HIDDEN CAMS. å Fasten the BOTTOM (E) to the UPRIGHT (C). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). Maximum 210 degrees Arrow Minimum 190 degrees B C E ith e w AMS c a f Sur DEN C HID 2S BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) Page 14 420421 www.sauder.
Step 11 å Fasten the RIGHT END (A) and LEGS (H and I) to the BOTTOM (E), PANELS (F), and SHELF (G). Tighten six HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees F G I E F A H www.sauder.
Step 12 å å å Carefully turn your unit onto its top. Push four FEET (38E) onto the LEGS (H and I). With your hammer, gently tap four TACK GLIDES (13E) through the FEET and into the LEGS. 13E 13E 38E H 38E I I H Page 16 420421 www.sauder.
Step 13 å Fasten the FOOT BRACKETS (6E) to the BOTTOM (E). Use six BLACK 9/16" LARGE HEAD SCREWS (1S). å å Slide the CENTER SUPPORTS (N) onto the FOOT BRACKETS (6E). Firmly push the CORNER CAPS (5E) onto the CENTER SUPPORTS (N). 5E 1S 5E BLACK 9/16" LARGE HEAD SCREW (6 used in this step) N N N N 6E 6E E www.sauder.
Step 14 å å Carefully stand your unit upright. Push six BUMPERS (2M) into the PANELS (F) and LEGS (H and I). 2M I F H F H I Page 18 420421 www.sauder.
Step 15 å Fasten the LIFT TABLE MECHANISMS (23M) to the TOP (D). Use six BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure to position the LIFT TABLE MECHANISMS on the TOP exactly as shown. 1S BLACK 9/16" LARGE HEAD SCREW (6 used in this step) 23M The holes are closer to this edge. D 23M www.sauder.
Step 16 å Fasten the SUPPORT BRACKETS (37G) to the LIFT TABLE MECHANISMS (23M). Use four WASHERS (13M), NUTS (24M), and BLACK 3/4" MACHINE SCREWS (92S). 92S 24M BLACK 3/4" MACHINE SCREW (4 used in this step) 13M 37G 23M D 23M 37G 24M Page 20 420421 13M www.sauder.
Step 17 å å IMPORTANT: You will need someone's help in this step. å å NOTE: Do not overtighten the SCREWS (85S). å NOTE: Be careful when lining up the holes in the MECHANISMS with the holes in the ENDS as to not damage any parts. You should start each SCREW a few turns before completely tightening any of them. Fasten the TOP (D) to the ENDS (A and B).
Step 18 å Fasten the BRACE (J) to the SUPPORT BRACKETS (37G) on the LIFT TABLE MECHANISMS (23M). Use four WASHERS (13M), NUTS (24M), and BLACK 1-1/4" MACHINE SCREWS (93S). 93S BLACK 1-1/4" MACHINE SCREW (4 used in this step) 13M 24M 23M J 37G 24M 23M 13M 37G Page 22 420421 www.sauder.
Step 19 å å å å IMPORTANT: Do not place valuables in the storage space. Push a CAM COVER (12P) onto each visible HIDDEN CAM. NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. And to celebrate, why not share your success story? 50 lbs. 25 lbs. 40 lbs. total 12P (16 used) To cover HIDDEN CAMS www.sauder.
Modèle 420421 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Ne pas serrer les CAMES ESCAMOTABLES dans cette étape. Avec précaution, retourner les EXTRÉMITÉS (A et B). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Fixer les autres PIEDS (H et I) aux EXTRÉMITÉS (A et B). Serrer six EXCENTRIQUES ESCAMOTABLES. Enfoncer vingt-quatre EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A et B), le DESSOUS (E), les deux PANNEAUX (F) et la TABLETTE (G).
ÉTAPE 11 ÉTAPE 16 Fixer l'EXTRÉMITÉ DROITE (A) et PIEDS (H et I) au DESSOUS (E), aux PANNEAUX (F) et à la TABLETTE (G). Serrer six EXCENTRIQUES ESCAMOTABLES. Fixer les CONSOLES DE SUPPORT (37G) sur les MÉCANISMES DE LEVAGE DE TABLE (23M). Utiliser quatre RONDELLES (13M), ÉCROUS (24M) et VIS À MÉTAUX 19 mm NOIRES (92S). ÉTAPE 12 ÉTAPE 17 Avec précaution, retourner l'élément sur son dessus. IMPORTANT : Faire appel à une autre personne pour cette étape. Fixer quatre PIEDS (38E) aux PIEDS (H et I).
Modelo 420421 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Cuidadosamente vuelva los EXTREMOS (A y B) al revés. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Fije las PATAS (H e I) restantes a los EXTREMOS (A y B). Apriete seis EXCÉNTRICOS ESCONDIDOS. Empuje veinticuatro EXCÉNTRICOS ESCONDIDOS (1F) dentro de los EXTREMOS (A y B), del FONDO (E), de los dos PANELES (F) y del ESTANTE (G).
PASO 11 PASO 16 Fije el EXTREMO DERECHO (A) y las PATAS (H e I) al FONDO (E), a los PANELES (F) y al ESTANTE (G). Apriete seis EXCÉNTRICOS ESCONDIDOS. Fije los SOPORTES DE APOYO (37G) a los MECANISMOS DE ELEVACIÓN DE LA MESA (23M). Utilice cuatro ARANDELAS (13M), PERNOS (24M) y TORNILLOS NEGROS PARA METAL de 19 mm (92S). PASO 12 Cuidadosamente voltee la unidad para que repose sobre el panel superior. Fije cuatro PATAS (38E) a las PATAS (H e I).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves. Place the heavier items on the lower shelves.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.