CONTACT US FIRST sauder.com BEFORE MAKING ANY RETURNS TO THE STORE. Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep. Prefer the phone? Give us a ring at 1-800-523-3987. Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays) WARNING CHOKING HAZARD - Small Parts Not for children under 3 years. Adult assembly required. Dresser Model 420456 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-18 Hammer Français 19-21 Español 22-24 Safety 25-26 Warranty Page 2 Not actual size Skip the power trip. This time. 27 420456 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/service/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push twenty HIDDEN CAMS (1F) into the ENDS (A2 and B2), UPRIGHT (C2), BRACES (F), and DRAWER BRACES (M67). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Some assembly (and snacks) required. Do not tighten the HIDDEN CAMS in this step.
Step 2 VIEW THE DRAWER GLIDE VIDEO å Fasten six UNIVERSAL CABINET RAILS* (35AA) to the ENDS (A2 and B2). Use twelve GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. å *patent pending glide system 3S GOLD 5/16" FLAT HEAD SCREW (12 used for the RAILS) Glide end 1 2 1 3 Finished edge 2 1 3 A2 3 2 3 2 3 1 withCAMS e c fa N Sur IDDE H 2 3 1 B2 2 1 withCAMS e c fa N Sur IDDE H Glide end Finished edge Page 6 420456 www.sauder.
Step 3 VIEW THE DRAWER GLIDE VIDEO å Fasten six UNIVERSAL CABINET RAILS* (35AA) to both surfaces of the UPRIGHT (C2). Use twelve GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. å *patent pending glide system 3S GOLD 5/16" FLAT HEAD SCREW (12 used for the RAILS) 3 Finished edge 2 3 1 2 3 1 2 1 C2 S HID urfac DEN e w CA ith MS 2 1 2 3 1 2 1 www.sauder.
Step 4 å Fasten the TOP MOLDING (J) to the TOP (D). Use four SILVER 1-1/8" FLAT HEAD SCREWS (10S). å å NOTE: Do not overtighten the SCREWS into the TOP. å NOTE: Position the SAFETY STRAP exactly as shown. 97 Open the FURNITURE TIPPING RESTRAINT KIT (97) and fasten the SAFETY STRAP to the TOP (D). Use the provided BLACK 9/16" LARGE HEAD SCREW.
Step 5 å Fasten the UPRIGHT (C2) to the TOP (D). Tighten two HIDDEN CAMS. å NOTE: Be sure to move the SAFETY STRAP on the TOP off to one side. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Rounded edge Finished edge D e fac Sur es hol h t i w C2 Sur withface HID CA DEN MS Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate. To completely tighten: www.
Step 6 å Fasten the BRACES (F) to the UPRIGHT (C2). Tighten four HIDDEN CAMS. Don't worry. It isn't Rome. This can be built in a day. These holes must be here. F MS CA N E IDD H h it ew c a f Sur F MS CA N E IDD H h it ew c a f Sur C2 F These holes must be here. F Maximum 210 degrees ith ew c a f Sur ith ew c a f Sur S AM C DEN HID S AM C DEN HID Arrow Minimum 190 degrees Page 10 420456 www.sauder.
Step 7 å Fasten the ENDS (A2 and B2) to the TOP (D) and BRACES (F). Tighten eight HIDDEN CAMS. Finished edge A2 D Finished edge Sur withface HID CA DEN MS F F F B2 Sur f HID ace w DEN itho CA ut MS Maximum 210 degrees F Arrow Minimum 190 degrees www.sauder.
Step 8 å Fasten five METAL BRACKETS (4G) to the BASE (G2). Use five BLACK 9/16" LARGE HEAD SCREWS (1S). å å NOTE: Be sure to use the exact holes shown in the BASE. 4G Fasten the BASE (G2) to the ENDS (A2 and B2) and UPRIGHT (C2). Use five BLACK 9/16" LARGE HEAD SCREWS (1S) through the BRACKETS on the BASE and into the ENDS and UPRIGHT. 4G G2 1S Curved edge BLACK 9/16" LARGE HEAD SCREW (10 used in this step) 4G A2 G2 C2 B2 Curved edge Page 12 420456 www.sauder.
Step 9 å Carefully turn your unit over onto its front edges. Unfold the BACK (E) and lay it over your unit. å A perforation in the BACK (E) has been provided for access to the SAFETY STRAP. Punch out the perforation and push the SAFETY STRAP through the hole. å Make equal margins along all four edges of the BACK (E). Push on opposite corners of your unit if needed to make it "square". å å Caution Do not stand the unit upright without the BACK fastened. The unit may collapse.
Step 10 å Fasten two METAL BRACKETS (4G) to the BRACES (F) and BASE (G2). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). å Using your hammer, gently tap six TACK GLIDES (13E) into the ENDS (A2 and B2), UPRIGHT (C2), and BASE (G2). 13E A2 F C2 G2 B2 F 4G 13E These two TACK GLIDES should be flush with the front surface of the BASE. Page 14 1S BLACK 9/16" LARGE HEAD SCREW (4 used for the BRACKETS) 420456 www.sauder.
Step 11 VIEW THE T-SLOT BOX VIDEO Push down 1 H 2 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. 9G D37 D974 Unfi nish ed sur fac D36 e Groove D36 1S H D37 BLACK 9/16" LARGE HEAD SCREW (20 used in this step) å Pull the DRAWER FRONT BRACKETS (9G) apart and slide them into the grooves in the DRAWER SIDES (D36 and D37). You may need to gently tap them in with a hammer. NOTE: The DRAWER FRONT BRACKETS are marked "RH" and "LH" for easy identification.
Step 12 å VIEW THE DRAWER GLIDE VIDEO Fasten a DRAWER RIGHT (35AC) to the RIGHT DRAWER SIDE (D36) and a DRAWER LEFT (35AD) to the LEFT DRAWER SIDE (D37). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #2. å å NOTE: The glides are not intended to rotate. å Repeat this step for the other drawers. Almost time to celebrate! With a nap. Fasten a KNOB (91K) to the LARGE DRAWER FRONT (H). Use a BLACK 1-1/8" PAN HEAD SCREW (9S).
Step 13 å å Carefully stand your unit upright in its final location. We recommend using the SAFETY STRAP for added stability. å NOTE: Do not turn the SAFETY DRYWALL ANCHOR into a wall stud. If you prefer to fasten the SAFETY STRAP to a wall stud, go to your local hardware store for proper hardware. å INSTALLATION INSTRUCTIONS: 1. Insert the SAFETY DRYWALL ANCHOR through the WASHER and the end of the SAFETY STRAP. 2.
Step 14 å To insert the drawers into your unit, tip the front of the drawers down and drop the glides on the drawers behind the glides on the unit. Lift the front of the drawers up and slide them into the unit. å To make adjustments to the drawers, loosen the SCREWS in the DRAWER FRONT BRACKETS, make needed adjustments, and tighten the SCREWS. å å NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly. Clean with a damp cloth. Wipe dry.
Modèle 420456 Commode Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 5 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer vingt EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A2 et B2), le MONTANT (C2), les ENTRETOISES (F) et les ENTRETOISES DE TIROIR (M67).
ÉTAPE 10 ÉTAPE 13 Fixer deux CONSOLES EN MÉTAL (4G) aux ENTRETOISES (F) et à la BASE (G2). Utiliser quatre VIS TÊTE LARGE 14 mm NOIRES (1S). Relever, avec précaution, l'élément dans sa position verticale et placer l'élément dans son emplacement final. Il est recommandé d'utiliser la SANGLE DE SÉCURITÉ pour renforcer la stabilité. À l'aide d'un marteau, enfoncer légèrement six PATINS (13E) dans les EXTRÉMITÉS (A2 et B2), UPRIGHT (C2) et BASE (G2).
Modelo 420456 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 5 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje veinte EXCÉNTRICOS ESCONDIDOS (1F) dentro de los EXTREMOS (A2 y B2), del PARAL (C2), de las RIOSTRAS (F) y de las RIOSTRAS DE CAJÓN (M67).
PASO 10 PASO 13 Fije dos SOPORTES DE METAL (4G) a las RIOSTRAS (F) y a la BASE (G2). Utilice cuatro TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). Cuidadosamente ponga la unidad en posición vertical y coloque su unidad en su posición final. Se recomienda que utilice la CORREA DE SEGURIDAD para aumentar la estabilidad. Utilizando un martillo, ligeramente clave seis TACHUELAS DESLIZANTES (13E) en los ENDS (A2 y B2), UPRIGHT (C2) y BASE (G2). Cuidadosamente corte el agujero perforado del DORSO (E).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following safety information. Death or serious injury may occur when children climb on furniture. A remote control, toys or other items placed on the furniture may encourage a child to climb on the furniture which could cause it to tip-over and result in serious injury or death. NEVER allow children to climb on furniture.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Lea cuidadosamente la siguiente información de seguridad. Pueden suceder lesiones graves o la muerte cuando los niños se suben en los muebles. Un control remoto, juguetes u otros artículos colocados en los muebles pueden alentar a un niño a subirse en el mueble, lo cual podría causar que se derribe y resultaría en lesiones graves o la muerte.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
If you need assistance please contact customer service at 800-523-3987 Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays) or at sauder.com/service. Register your new product online For immediate service, 24 hours per day, 7 days per week, to order replacement parts, access assembly tips and register your product, visit www.sauder.com/service So, how did it go? Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
