sauder.com Here's one for the books. 5-Shelf Bookcase 419200 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-14 Français pg 15-17 Español pg 18-20 Lot # 371565 04/07/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-14 Hammer Français 15-17 Español 18-20 Safety 21-22 Warranty Page 2 Not actual size Skip the power trip. This time. 23 419200 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. A RIGHT END (1) B LEFT END (1) C TOP/BOTTOM (2) D SHELF (1) E BACK (1) F ADJUSTABLE SHELF (3) G BASE (1) H END MOLDING (2) I TOP MOLDING (1) J SHELF MOLDING (4) E C I F J A H F B D J J H F J C G www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 10F TWIST-LOCK® FASTENER - 12 5G ANGLE BRACKET - 6 1S Page 4 1G 1N SAFETY BRACKET - 1 1R NAIL - 46 METAL PIN - 12 3G TIE PLATE - 4 2R RUBBER SLEEVE - 12 16S BLACK 1-7/8" PAN HEAD SCREW - 1 BLACK 9/16" LARGE HEAD SCREW - 21 419200 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (10F) into the large holes in a TOP/BOTTOM (C) and SHELF (D). å Repeat this step for the other TOP/BOTTOM (C). Do not tighten the TWIST-LOCK® FASTENERS in this step. 10F (12 used) D C 10F www.sauder.
Step 2 å å Fasten six ANGLE BRACKETS (5G) to the TOP/BOTTOMS (C). Use six BLACK 9/16" LARGE HEAD SCREWS (1S). Remember: Righty tighty. Lefty loosey. NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edges of the TOP/BOTTOMS. C C 5G 1S BLACK 9/16" LARGE HEAD SCREW (6 used in this step) Page 6 419200 www.sauder.
Step 3 å Slide the END MOLDINGS* (H) onto the notched edges of the ENDS (A and B). å *U.S. Patent No. 5,499,886 A H Notched edge B H Slide the END MOLDING (H) onto the notched edge. www.sauder.
Step 4 å Slide the SHELF MOLDING* (J) onto the notched edge of the SHELF (D). å *U.S. Patent No. 5,499,886 RS NE E ST A th ® F wi CK ce O rfa T-L Su IS TW D Notched edge These edges must be even. J Slide the SHELF MOLDING (J) onto the notched edge. Page 8 419200 www.sauder.
Step 5 å Fasten the TOP/BOTTOMS (C) and SHELF (D) to the ENDS (A and B). Tighten twelve TWIST-LOCK® FASTENERS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2.
Step 6 å Fasten the BASE (G) and TOP MOLDING (I) to the TOP/ BOTTOMS (C). Use six BLACK 9/16" LARGE HEAD SCREWS (1S) through the ANGLE BRACKETS on the TOP/BOTTOMS and into the BASE and TOP MOLDING. Don't worry. It isn't Rome. This can be built in a day. Unfinished edge 1S I BLACK 9/16" LARGE HEAD SCREW (6 used in this step) C G C Unfinished edge Page 10 419200 www.sauder.
Step 7 å å Carefully turn your unit over onto its front edges. å Fasten two TIE PLATES (3G) to the END MOLDINGS (H) and the TOP MOLDING (I). Use four BLACK 9/16” LARGE HEAD SCREWS (1S). å NOTE: There are no pre-drilled holes in the END MOLDINGS. The SCREWS will tighten into the grooves. Fasten two TIE PLATES (3G) to the END MOLDINGS (H) and the BASE (G). Use four BLACK 9/16” LARGE HEAD SCREWS (1S). (4 used) 3G H I H G 1S BLACK 9/16" LARGE HEAD SCREW (8 used in this step) 3G H G 3G www.sauder.
Step 8 å å Unfold the BACK (E) and lay it over your unit. å å Fasten the BACK (E) to your unit using the NAILS (1N). å NOTE: Perforations have been provided for access through the BACK. Carefully cut out the holes needed. Caution Make equal margins along all four edges of the BACK (E). Push on opposite corners of your unit if needed to make it "square". Do not stand the unit upright without the BACK fastened. The unit may collapse.
Step 9 å Slide the SHELF MOLDING* (J) onto the notched edge of the ADJUSTABLE SHELF (F). å å Repeat this step for the other ADJUSTABLE SHELVES (F). Almost time to celebrate! With a nap. *U.S. Patent No. 5,499,886 These surfaces should be even. F Notched edge J Slide the SHELF MOLDING (J) onto the notched edge. www.sauder.
Step 10 å å Carefully stand your unit upright. å We recommend using the SAFETY BRACKET (1G) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (1S) into the top of the unit and a BLACK 1-7/8" PAN HEAD SCREW (16S) into a stud in your wall. å å NOTE: Please read the back pages of the instruction booklet for important safety information. Push the RUBBER SLEEVES (2R) over the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B).
419200 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Fixer la BASE (G) et la MOULURE DE DESSUS (I) aux pièces DESSUS/DESSOUS (C). Utiliser six VIS TÊTE LARGE 14 mm NOIRES (1S) à travers les CONSOLES À ÉQUERRE situées sur les DESSUS/DESSOUS, et dans la BASE et la MOULURE DE DESSUS. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol.
ÉTAPE 9 ÉTAPE 10 Enfiler la MOULURE DE TABLETTE* (J) sur le chant cranté de la TABLETTE RÉGLABLE (F). Relever, avec précaution, l'élément dans sa position verticale. Répéter cette étape pour les autres TABLETTES RÉGLABLES (F). * Brevet État Unis n° 5,499,886 Enfoncer les MANCHONS EN CAOUTCHOUC (2R) sur les GOUPILLES EN MÉTAL (1R). Insérer les GOUPILLES EN MÉTAL dans les trous choisis dans les EXTRÉMITÉS (A et B). Poser les TABLETTES RÉGLABLES (F) sur les GOUPILLES EN MÉTAL.
419200 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 No apriete los SUJETADORES TWIST-LOCK® en este paso. Fije la BASE (G) y la MOLDURA DE PANEL SUPERIOR (I) a las partes PANEL SUPERIOR / FONDO (C). Utilice seis TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S) a través de los SOPORTES ANGULARES sujetados a las partes PANEL SUPERIOR / FONDO y dentro de la BASE y la MOLDURA DE PANEL SUPERIOR. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso.
PASO 9 PASO 10 Deslice la MOLDURA DE ESTANTE* (J) sobre el borde con muesca del ESTANTE AJUSTABLE (F). Cuidadosamente ponga la unidad en posición vertical. Repita este paso para los otros ESTANTES AJUSTABLES (F). *Patente EE. UU. No. 5,499,886 Empuje los MANGUITOS DE GOMA (2R) sobre las ESPIGAS DE METAL (1R). Inserte las ESPIGAS DE METAL en los agujeros al nivel preferido de los EXTREMOS (A y B). Coloque los ESTANTES AJUSTABLES (F) sobre las ESPIGAS DE METAL.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes sobrecargados. • Cargar el producto inadecuadamente puede causar la inestabilidad. • Riesgo de lesiones. • El mobiliario inestable puede volcarse. • Estantes sobrecargados pueden romper.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
