sauder.com Sweet stand. Sweet dreams. Side Table/Night Stand County Line Collection | 417771 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-15 Français pg 16-18 Español pg 19-21 Lot # 369649 03/10/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-15 Hammer Français 16-18 Español 19-21 Safety 22 Warranty 23 Page 2 Not actual size 417771 www.sauder.
Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 35GA CABINET RIGHT - 1 1F HIDDEN CAM - 24 7G DRAWER FRONT BRACKET - 1 1S 35GC DRAWER RIGHT - 1 35GB CABINET LEFT - 1 8F 98K PULL - 1 3S BLACK 9/16" LARGE HEAD SCREW - 10 13P CAM COVER - 8 GOLD 5/16" FLAT HEAD SCREW - 8 61S SILVER 1/4" MACHINE SCREW - 2 30S BLACK 1-9/16" FLAT HEAD SCREW - 4 Page 4 4G METAL BRACKET - 4 CAM SCREW - 24 10I WASHER - 2 35GD DRAWER LEFT - 1 417771 www.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push twenty-four HIDDEN CAMS (1F) into the ENDS (A), BACK (D), LONG FRONT/BACK SKIRTS (I), and SHORT SIDE SKIRTS (J). Arrow A 1F A D I I Arrow 1F (24 used) J J Arrow Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. www.sauder.
Step 2 å Turn twenty-four CAM SCREWS (8F) into the TOP (B) and LEGS (E, F, G, and H). å Fasten four METAL BRACKETS (4G) to the SKIRTS (I and J). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). 8F G H E F B 8F (24 used) The BRACKET should be even with the edge. 4G I I 1S J BLACK 9/16" LARGE HEAD SCREW (4 used in this step) Page 6 J 417771 www.sauder.
Step 3 å Fasten the LEGS (E, F, G, and H) to the ENDS (A) and SHORT SIDE SKIRTS (J). Tighten twelve HIDDEN CAMS. These surfaces must be even. S HI urfa DD ce EN wi CA th M S E A Metal bracket These surfaces must be even. Finished edge J S HI urfa DD ce EN wi CA th M S G H A Metal bracket Finished edge J F 1 www.sauder.
Step 4 å Fasten a CABINET RIGHT (35GA) and a CABINET LEFT (35GB) to the ENDS (A). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. å NOTE: Use the holes shown. 3S GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Roller end 1 2 3 A 3 2 1 Roller end Page 8 A 417771 www.sauder.
Step 5 å Fasten the BACK (D) and LONG BACK SKIRT (I) to the LEFT REAR LEG (H). Tighten three HIDDEN CAMS. å Fasten the LONG FRONT SKIRT (I) to the LEFT FRONT LEG (F). Tighten one HIDDEN CAM. Sur withface HID CA DEN MS Finished edge D Metal bracket I H Metal bracket I F 1 www.sauder.
Step 6 å Fasten the BACK (D) and LONG BACK SKIRT (I) to the RIGHT REAR LEG (G). Tighten three HIDDEN CAMS. å Fasten the LONG FRONT SKIRT (I) to the RIGHT FRONT LEG (E). Tighten one HIDDEN CAM. å Fasten the BOTTOM (C) to the SKIRTS (I and J). Use four BLACK 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKETS and into the BOTTOM. å Push a CAM COVER (13P) onto each HIDDEN CAM on the SKIRTS (I and J).
Step 7 Carefully stand your unit upright. Fasten the TOP (B) to the ENDS (A). Tighten four HIDDEN CAMS. B S w urf C ith ac S AM ou e C t R E W S å å Long edge A A 1 www.sauder.
Step 8 å Fasten the DRAWER SIDES (D42 and D43) to the DRAWER BACK (D154). Use four BLACK 1-9/16" FLAT HEAD SCREWS (30S). å Slide the DRAWER BOTTOM (D960) into the grooves in the DRAWER SIDES and DRAWER BACK. 30S BLACK 1-9/16" FLAT HEAD SCREW (4 used in this step) D43 D154 D42 Groove Be sure the DRAWER BOTTOM inserts into the DRAWER BACK groove. D154 D960 D42 ed h is e n ac Fi urf s D43 With the palm of your hand, tap the DRAWER BOTTOM into the grooves. Page 12 417771 www.sauder.
Step 9 å Pull the DRAWER FRONT BRACKETS (7G) apart and slide them into the grooves in the DRAWER SIDES (D42 and D43). You may need to gently tap them in with a hammer. å NOTE: The DRAWER FRONT BRACKETS are marked “RH” and “LH” for easy identification. å Fasten the DRAWER FRONT (K) to the DRAWER FRONT BRACKETS (7G). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). 1S Push down BLACK 9/16" LARGE HEAD SCREW (2 used in this step) 7G D43 D42 K www.sauder.
Step 10 å Fasten a DRAWER RIGHT (35GC) to the DRAWER RIGHT SIDE (D42) and a DRAWER LEFT (35GD) to the DRAWER LEFT SIDE (D43). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. å Fasten the PULL (98K) to the DRAWER FRONT (K). Use two WASHERS (10I) and two SILVER 1/4" MACHINE SCREWS (61S). Roller end 61S 1 3 SILVER 1/4" MACHINE SCREW (2 used for the PULL) 10I 2 D43 Roller end K D42 1 98K 3 2 3S GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Page 14 417771 www.sauder.
Step 11 å To insert the drawer into your unit, tip the front of the drawer down and drop the rollers on the drawer behind the rollers on the unit. Lift the front of the drawer up and slide it into the unit å To make adjustments to the drawers, loosen the SCREWS in the DRAWER FRONT BRACKETS, make needed adjustments, and tighten the SCREWS. å å NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly.
417771 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 4 Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Fixer une ÉLÉMENT DROITE (35GA) et une ÉLÉMENT GAUCHE (35GB) aux EXTRÉMITÉS (A). Utiliser quatre VIS TÊTE PLATE 8 mm DORÉES (3S) à travers les trous nº 1 et nº 3. Enfoncer vingt-quatre EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A), l’ARRIÈRE (D), les PLINTHES LONGUES AVANT/ARRIÈRE (I) et les PLINTHES LATÉRALES COURTES (J).
ÉTAPE 7 ÉTAPE 10 Relever, avec précaution, l'élément dans sa position verticale. Fixer le DESSUS (B) aux EXTRÉMITÉS (A). Serrer quatre EXCENTRIQUES ESCAMOTABLES. Fixer un TIROIR DROIT (35GC) sur le CÔTÉ DROIT DE TIROIR (D42) et un TIROIR GAUCHE (35GD) sur le CÔTÉ GAUCHE DE TIROIR (D43). Utiliser quatre VIS TÊTE PLATE 8 mm DORÉES (3S) à travers les trous nº 1 et nº 3. ÉTAPE 8 Fixer la POIGNÉE (98K) au DEVANT DE TIROIR (K). Utiliser deux RONDELLES (10I) et deux VIS À MÉTAUX 6 mm ARGENTÉES (61S).
417771 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 4 Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Fije un GABINETE DERECHO (35GA) y un GABINETE IZQUIERDO (35GB) a los EXTREMOS (A). Utilice cuatro TORNILLOS DORADOS DE CABEZA PERDIDA de 8 mm (3S) a través de los agujeros No. 1 y No. 3. Empuje veinticuatro EXCÉNTRICOS ESCONDIDOS (1F) en los EXTREMOS (A), el DORSO (D), FALDONES LARGOS DELANTEROS / POSTERIORES (I) y FALDONES LATERALES CORTOS (J).
PASO 7 PASO 10 Cuidadosamente ponga la unidad en posición vertical. Fije un CAJÓN DERECHO (35GC) al LADO DERECHO DE CAJÓN (D42) y un CAJÓN IZQUIERDO (35GD) al LADO IZQUIERDO DE CAJÓN (D43). Utilice cuatro TORNILLOS DORADOS DE CABEZA PERDIDA de 8 mm (3S) a través de los agujeros No. 1 y No. 3. Fije el PANEL SUPERIOR (B) a los EXTREMOS (A). Apriete cuatro EXCÉNTRICOS ESCONDIDOS. PASO 8 Fije los LADOS DE CAJÓN (D42 y D43) al DORSO DE CAJÓN (D154).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded drawers and shelves. • Risk of injury. • Never exceed the weight limits shown in • Top-heavy furniture can tip over. the instructions. • Overloaded drawers or shelves can break. • Work from bottom to top when loading shelves and drawers.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
