sauder.com Treat yourshelf. Storage Cabinet Coral Cape Collection | Model 423808 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-26 Français pg 27-31 Español pg 32-36 Lot # 528899 06/05/19 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4-5 6-26 Hammer Français 27-31 Español 32-36 Safety 37-38 Warranty Page 2 Not actual size Skip the power trip. This time. 39 423808 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 1S 25S BLACK 9/16" PAN HEAD SCREW - 14 BLACK 9/16" LARGE HEAD SCREW - 10 37S BLACK 7/8" MACHINE SCREW - 2 113S BLACK 1-15/16" FLAT HEAD SCREW - 2 123S BLACK 5/8" FLAT HEAD SCREW - 2 127S BLACK 3/8" MACHINE SCREW - 4 129S GOLD 1/2" PAN HEAD SCREW - 4 130S GOLD 5/8" FLAT HEAD SCREW - 3 140S BLACK 5/8" LARGE HEAD SCREW - 4 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push thirteen HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHT (D), BOTTOM (F), and TOP MOLDING (G). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. Insert the metal end of the CAM DOWEL into the HIDDEN CAM.
Step 2 å Push twenty HIDDEN CAMS (1F) into the ENDS (A and B). Some assembly (and snacks) required. (20 used) Arrow 1F A B Arrow 1F Arrow Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. www.sauder.
Step 3 å Turn twenty CAM SCREWS (8F) into the exact holes shown in the LEGS (C, J, and K). 8F (20 used) K K J C Page 8 423808 www.sauder.
Step 4 å å Insert one WOOD DOWEL (15F) into the RIGHT REAR LEG (J). å NOTE: Be sure the WOOD DOWEL in the LEG inserts into the END. å å Insert one WOOD DOWEL (15F) into the RIGHT END (A). å NOTE: Be sure the WOOD DOWEL in the END inserts into the LEG. Fasten the RIGHT END (A) to the RIGHT REAR LEG (J). Tighten five HIDDEN CAMS. 1 2 Fasten one of the FRONT LEGS (K) to the RIGHT END (A). Tighten five HIDDEN CAMS. Edge with CAM DOWELS K A These surfaces should be even.
Step 5 å å Insert one WOOD DOWEL (15F) into the LEFT REAR LEG (C). å NOTE: Be sure the WOOD DOWEL in the LEG inserts into the END. å å Insert one WOOD DOWEL (15F) into the LEFT END (B). å NOTE: Be sure the WOOD DOWEL in the END inserts into the LEG. Fasten the LEFT END (B) to the LEFT REAR LEG (C). Tighten five HIDDEN CAMS. Fasten the remaining FRONT LEG (K) to the LEFT END (B). Tighten five HIDDEN CAMS.
Step 6 å Fasten the TOP MOLDING (G) to the TOP (O). Tighten three HIDDEN CAMS. å Open the FURNITURE TIPPING RESTRAINT KIT (97) and fasten the SAFETY STRAP to the TOP (O). Use the provided BLACK 9/16" LARGE HEAD SCREW. å NOTE: Position the SAFETY STRAP exactly as shown. Meet Part (O). This component has been engineered to be lighter, stronger, faster… well ok. Not technically faster. But definitely makes for a sturdier Storage Cabinet that’s easier to assemble and friendlier to the environment.
Step 7 å Fasten the LEFT END (B) and UPRIGHT (D) to the TOP (O). Tighten four HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. Notch Curved edge G O K B ith ew c a f Sur Page 12 S AM C DEN HID D 423808 ith e w AMS c a f Sur DEN C HID www.sauder.
Step 8 å Center the DOOR TRACK (140M) over the groove in the BOTTOM (F) and insert it into the groove. å NOTE: You may need to gently tap the DOOR TRACK into the groove in the BOTTOM using your hammer. å Fasten the BOTTOM (F) to the LEFT END (B). Tighten two HIDDEN CAMS. å Fasten the BOTTOM (F) to the UPRIGHT (D). Use two BLACK 1-15/16" FLAT HEAD SCREWS (113S).
Step 9 å Fasten the RIGHT END (A) to the BOTTOM (F) and TOP (O). Tighten four HIDDEN CAMS. Maximum 210 degrees Arrow Minimum 190 degrees O F Page 14 ut itho S w e fac AM Sur DEN C HID 423808 A www.sauder.
Step 10 å Fasten three METAL BRACKETS (4G) to the BOTTOM MOLDING (H). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). Hey! It's starting to look like something! å NOTE: Be sure the BRACKETS are even with the edge of the BOTTOM MOLDING. å Fasten the BOTTOM MOLDING (H) to the BOTTOM (F). Use three BLACK 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKETS on the BOTTOM MOLDING and into the holes in the BOTTOM. 1S BLACK 9/16" LARGE HEAD SCREW (6 used in this step) 4G H H F www.sauder.
Step 11 å Carefully turn your unit over onto its front edges. Unfold the BACK (L) and lay it over your unit. å A perforation in the BACK (L) has been provided for access to the SAFETY STRAP. Punch out the perforation and push the SAFETY STRAP through the hole. å Fasten the BACK (L) to the REAR LEGS (C and J). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). å Finish fastening the BACK (L) to your unit using the NAILS (1N). Caution Do not stand the unit upright without the BACK fastened.
Step 12 å å Carefully stand your unit upright in its final location. We recommend using the SAFETY STRAP for added stability. å INSTALLATION INSTRUCTIONS: 1. Insert the SAFETY DRYWALL ANCHOR through the WASHER and the end of the SAFETY STRAP. 2. Using a Phillips screwdriver or a hand drill, press the screw slightly onto the drywall just below the top surface of your unit so the SAFETY STRAP will not be visible. 3.
Step 13 å Fasten three DOOR TRACK SUPPORTS (170M) to the TOP MOLDING (G). Use three GOLD 5/8" FLAT HEAD SCREWS (130S). å NOTE: Be sure to position the DOOR TRACK SUPPORTS exactly as shown. G Large hole 170M 130S GOLD 5/8" FLAT HEAD SCREW (3 used in this step) Page 18 423808 www.sauder.
Step 14 å å å NOTE: The DOOR PANEL (M) is reversible. Place the DOOR PANEL (M) down into the DOOR FRAME (P). Fasten the DOOR PANEL (M) to the DOOR FRAME (P). Use fourteen CLIPS (46M) and fourteen BLACK 9/16" PAN HEAD SCREWS (25S). M ill e w ide c a f s r s su e in it. Thi ace thour un f fy o 25S BLACK 9/16" PAN HEAD SCREW (14 used in this step) P 46M 46M P M 46M 46M www.sauder.
Step 15 å Fasten the DOOR WHEELS (98M) to the WHEEL SUPPORTS (169M). Use two LONG BARREL NUTS (154M) and two BLACK 5/8" FLAT HEAD SCREWS (123S). å Fasten the WHEEL SUPPORTS (169M) to the DOOR FRAME (P). Use four BARREL NUTS (115M) and four BLACK 3/8" MACHINE SCREWS (127S). å NOTE: Be sure to position the WHEEL SUPPORTS exactly as shown.
Step 16 å Fasten two RETAINING BARS (155M) to the DOOR FRAME (P). Use four BLACK 5/8" LARGE HEAD SCREWS (140S). å å å NOTE: Be sure to position the RETAINING BARS exactly as shown. NOTE: The RETAINING BARS should move up and down easily. Fasten the PULL (179K) to the DOOR FRAME (P). Use two BLACK 7/8" MACHINE SCREWS (37S). 140S BLACK 5/8" LARGE HEAD SCREW (4 used for the RETAINING BARS) The RETAINING BARS should move up and down easily.
Step 17 å Fasten two DOOR STOPS (171M) to the DOOR TRACK TUBE (168M). Use two GOLD 1/2" PAN HEAD SCREWS (129S). å NOTE: The SCREWS may turn in hard. Use a little extra force while turning these SCREWS. å Then, place the DOOR FRAME (P) onto the center of the DOOR TRACK TUBE (168M) as shown below. 168M 171M 129S 171M 168M 129S GOLD 1/2" PAN HEAD SCREW (2 used in this step) P 168M Page 22 423808 www.sauder.
Step 18 å NOTE: You will lift the DOOR by holding onto the ends of the DOOR TRACK TUBE while the DOOR hangs from the TUBE. å å NOTE: A corner of the unit is cut out to show part of the assembly. å Now, fasten the DOOR TRACK TUBE (168M) to the two outer DOOR TRACK SUPPORTS (170M). Use two GOLD 1/2" PAN HEAD SCREWS (129S). å Carefully pull the bottom of the DOOR FRAME (P) out at an angle.
Step 19 å The DOOR may need some side to side adjustments. Follow the text below to make needed adjustments. å NOTE: The spacing between the DOOR and the side of your unit should be even from top to bottom. å Slide the DOOR over to the side of your unit. Then, loosen the SCREWS in the WHEEL SUPPORTS a 1/4 of a turn, make any needed adjustments, and tighten the SCREWS. Loosen these SCREWS a 1/4 of a turn, make adjustments, and tighten. Page 24 423808 www.sauder.
Step 20 å Using your hammer, gently tap a CAM COVER (36P) onto each visible HIDDEN CAM. å Push the RUBBER SLEEVES (2R) over the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B) and UPRIGHT (D). Set the ADJUSTABLE SHELVES (E) onto the METAL PINS. E E B E 36P D E A (22 used) E To cover HIDDEN CAMS E 1R (24 used) www.sauder.
Step 21 å å IMPORTANT: The BUMPERS are used to reduce the risk of fingers being pinched when sliding the DOOR. å å NOTE: Please read the back pages of the instruction booklet for important safety information. Peel the BUMPERS from the BUMPER CARDS (29M) and stick the BUMPERS on the upper and lower corners of both sides of the DOOR FRAME (P). This completes assembly. Clean with a damp cloth. Wipe dry. And to celebrate, why not share your success story? No loa d 2 lbs. 5 25 lbs. 29M 2 lbs.
Modèle 423808 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 5 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Insérer une CHEVILLE EN BOIS (15F) dans le PIED ARRIÈRE GAUCHE (C). Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Fixer l’EXTRÉMITÉ GAUCHE (B) au PIED ARRIÈRE GAUCHE (C). Serrer cinq EXCENTRIQUES ESCAMOTABLES. Enfoncer treize EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A et B), le MONTANT (D), le DESSOUS (F) et la MOULURE DE DESSUS (G).
ÉTAPE 7 ÉTAPE 11 Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Fixer l'EXTRÉMITÉ GAUCHE (B) et le MONTANT (D) au DESSUS (O). Serrer quatre EXCENTRIQUES ESCAMOTABLES. Avec précaution, retourner l'élément sur ses chants avant. Déplier l'ARRIÈRE (L) et le placer sur l'élément.
ÉTAPE 13 ÉTAPE 16 Fixer trois SUPPORTS DE RAIL DE PORTE (170M) à la MOULURE DE DESSUS (G). Utiliser trois VIS TÊTE PLATE 16 mm DORÉES (130S). Fixer deux LANGUETTES DE RETENUE (155M) sur le CADRE DE PORTE (P). Utiliser quatre VIS TÊTE LARGE 16 mm NOIRES (140S). REMARQUE : S’assurer de positionner les SUPPORTS DE RAIL DE PORTE comme l'indique le schéma. REMARQUE : S’assurer de positionner les LANGUETTES DE RETENUE exactement comme il l’est indiqué.
ÉTAPE 18 ÉTAPE 20 REMARQUE : Il faudra ensuite lever la PORTE en tenant les extrémités du TUBE DE RAIL DE PORTE. La PORTE est suspendue au TUBE. À l'aide d'un marteau, enfoncer un COUVERCLE D'EXCENTRIQUE (36P) sur chaque EXCENTRIQUE ESCAMOTABLE visible. REMARQUE : Un coin de l’unité a été découpé pour montrer une partie de l’assemblage. Placer le TUBE DE RAIL DE PORTE (168M) avec le CADRE DE PORTE (P) sur les SUPPORTS DE RAIL DE PORTE (170M).
Modelo 423808 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 5 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Inserte un PASADOR DE MADERA (15F) en la PATA POSTERIOR IZQUIERDA (C). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje trece EXCÉNTRICOS ESCONDIDOS (1F) dentro de los EXTREMOS (A y B), del PARAL (D), del FONDO (F) y de la MOLDURA DE PANEL SUPERIOR (G). A continuación, inserte el extremo de metal de un PASADOR DE EXCÉNTRICO (2F) dentro de cada EXCÉNTRICO ESCONDIDO.
PASO 7 PASO 11 Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Fije el EXTREMO IZQUIERDO (B) y el PARAL (D) al PANEL SUPERIOR (O). Apriete cuatro EXCÉNTRICOS ESCONDIDOS. Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Desdoble el DORSO (L) y colóquelo sobre la unidad.
PASO 13 PASO 16 Fije tres SOPORTES DE CARRIL DE LA PUERTA (170M) a la MOLDURA DE PANEL SUPERIOR (G). Utilice tres TORNILLOS DORADOS DE CABEZA PERDIDA de 16 mm (130S). Fije dos BARRAS DE RETENCIÓN (155M) al MARCO DE LA PUERTA (P). Utilice cuatro TORNILLOS NEGROS DE CABEZA GRANDE de 16 mm (140S). NOTA: Asegúrese de colocar los SOPORTES DE CARRIL DE LA PUERTA exactamente como se muestra. NOTA: Asegúrese de que posicionar las BARRAS DE RETENCIÓN exactamente como se muestra.
PASO 18 PASO 20 NOTA: Levantará la PUERTA sosteniéndola en los extremos del TUBO DE CARRIL DE LA PUERTA mientras que la PUERTA cuelga del TUBO. Con un martillo, empuje una CUBIERTA DE EXCÉNTRICO (36P) sobre cada EXCÉNTRICO ESCONDIDO visible. NOTA: Una esquina de la unidad es cortada para mostrar parte del montaje. Coloque el TUBO DE CARRIL DE LA PUERTA (168M) con el MARCO DE LA PUERTA (P) en los SOPORTES DE CARRIL DE LA PUERTA (170M). Empuje los MANGUITOS DE GOMA (2R) sobre las ESPIGAS DE METAL (1R).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following safety information. Death or serious injury may occur when children climb on furniture. A remote control, toys or other items placed on the furniture may encourage a child to climb on the furniture which could cause it to tip-over and result in serious injury or death. NEVER allow children to climb on furniture.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Lea cuidadosamente la siguiente información de seguridad. Pueden suceder lesiones graves o la muerte cuando los niños se suben en los muebles. Un control remoto, juguetes u otros artículos colocados en los muebles pueden alentar a un niño a subirse en el mueble, lo cual podría causar que se derribe y resultaría en lesiones graves o la muerte.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
