User Manual
USING BACK PANEL TO ADJUST BRIGHTNESS AND KELVIN TEMPERATURE
(5) It is possible to control groups of lights in addition to operating them on multiple channels.
For instance, you can set one or more lights to Group A and other sets of lights to Group B,
Group C through Group F (6 Groups). You can then control all lights in the same group
simultaneously if they are all on the same channel 1-50. Individual lights in the same group can
also be adjusted independently within the same group if they are set to different channels.
To set the group number for a particular light, press the controller knob in and hold for 2 seconds.
When the Group selector begins to flash, remove your finger. Before the third flash, turn the Group
selector counterclockwise to select a lower group or clockwise to select a higher group. When the
controller knob is pressed in and held, it will alternate between the Group Selector and the Channel
Selector. Remove you finger while the desired selector is flashing.
(1) Turn on by pushing On/Off button to the ON position.
(2) Adjust brightness by turning the controller knob clockwise to brighten
or counterclockwise to dim. There is a second controller knob on the front
of the light for self-portrait applications. All adjustments are the same for
both controller knobs.
(3) To adjust Kelvin temperature, press controller knob in one time. Once the Kelvin Temperature
Readout begins to flash, turn the controller knob counterclockwise for warmer or clockwise
for cooler Kelvin temperature output.The Savage Luminous Pro LED Ringlight Plus can be set
to control groups of other lights together when using the included remote control. Multiple
lights in the same group can be controlled independently of each other using separate
channels. Savage’s Edgelight Pro LED panels are compatible with and can be used with
the same remote as the Ringlight Plus using the group and channel functions.
(4) To select a "Channel", press and hold the controller knob until the channel indicator
begins to flash and then remove finger from controller knob. While the channel selector
is flashing, turn the channel selector knob counterclockwise to select a lower channel
number or clockwise to select a higher channel. If the controller number is pressed in
for 2 seconds, it will alternate between the group selector and the channel selector
until you remove your finger. Select any channel between 1 and 50. If more than one
Savage Ringlight Plus is being used or if using in conjunction with the Savage Edge Light Pro,
all units that are on the same channel and in the same group will be controlled simultaneously
using the included remote control. Any lights that are not in the selected channel or group will
not be controlled.
Usage
Instructions
ON/OFF BUTTON
KELVIN TEMPERATURE INDICATOR
CONTROLLER
KNOB
- COOL LIGHT
- BRIGHT
- WARM LIGHT
- DIM
USING THE INCLUDED REMOTE CONTROL
(1) Make sure the power button on the back of Ringlight Plus is in the On position.
The On/Off switch on the remote control will not function if the light’s power switch is off.
(2) Press the remote control power button one time.
(3) The Group and Channel settings on the remote control must match the group and
power setting on the light’s back display. The remote control will not control the Ringlight
Plus unless the groups and channels match.
(4) Adjust the channel setting on the remote control by pressing the Ch/Grp button until
the channel number begins to flash. Change to higher channels by pushing the + symbol
on the remote and lower channels by pressing the – symbol.
(5) Select the Group number on the remote by pressing the Ch/Grp button until the group
letter begins to flash. Use the + button to select a lower letter in the alphabet and the minus
button to select a higher letter.
(6) After the channel/ group numbers are set to the corresponding channel/group numbers
on the back of the light, press + to brighten and - to darken.
(7) To change the Kelvin temperature, press the Set button on the remote until the Kelvin
temperature readout begins to flash. Use the + to cool the color temperature of the light and
the - button to warm.Only use included Sony NP-F batteries with the AC power cord removed.
Only use the AC power cord when the batteries are removed.
Only use included Sony NP-F batteries with the AC power cord removed.
Only use the AC power cord when the batteries are removed.
CHANNEL
INDICATOR
GROUP
INDICATOR
CHANNEL
INDICATOR
GROUP
INDICATOR
CONTROLLER KNOB