User Manual

ManualsBrandsSavage ManualsContinuous LightingRainbow RGB Ring Light

RGB RAINBOW RINGLIGHT

USAGE INSTRUCTIONS

(1) Power Switch

(2) Battery Compartments

(3) Battery Button

(4) AC Power Plug

(5) CCT - Color Correction Button

(6) Selector Knob

(7) Hue/Saturation Button

professional photography made simple

800.624.8891 savageUniversal.com

Using Included Batteries:

Flip the power switch [1] to the Battery position.

Slide included Sony style NP-F750 batteries in by dropping each in to the top of the

battery compartment and then sliding down until the battery snaps into place [2].

Note: The max run time for the Savage RGB Ringlight is approximately 90 minutes

(daylight mode) or 150 minutes (RGB mode) at full power.

To check remaining battery life, press the button on the back panel marked “Battery” [3].

The number displayed will be the percentage of battery life remaining.

To remove, simply push up on the battery until it releases.

The light comes with 2 wall chargers for the included batteries.

Fully drained batteries will take approximately 6 hours to restore to a full charge.

AC Power Option

Flip the power switch [1] to the AC position.

Your Savage Ringlight can also be used with the included AC power supply for continuous use.

Insert cord into the AC plug [4] located on the back side of the light. Remove battery when using

AC cord as the light will not recharge the battery when both are attached.

Ringlight Control Settings

DAYLIGHT MODE

To set to daylight/tungsten mode, press the button on the back panel marked “CCT” [5].

Turn the “Selector Knob” [6] clockwise to increase the color temperature to as high as 9999K.

Note: 5500K is daylight. Turn the Selector Knob counterclockwise to adjust the color temperature to

as low as 2700K.

Note: 3200K is considered tungsten. Adjusting the color temperature between

3200K and 5500K will generally allow the user to match the available light in any room.

Adjustments above 5500K will make the subject look cooler/bluer. Adjustments below 3200K

will warm the subject below the look of an incandescent bulb (generally around 3200K).

To adjust brightness, press the selector knob.

The light can be adjusted from 20% to 100% in CCT mode and 20% to 100% in RGB mode.

RGB MODE

Press the button on the back panel marked “Hue/Saturation” [7].

The light will display the letter “H”, followed by a number between 0 and 360.

These are reference numbers so that you can record and select the same

color for future use.

0 = RED 120 = GREEN 240= BLUE

After making a color selection, press the Hue/Saturation button [7] a second time to

adjust the saturation/intensity of the selected color.

DISPLAY

HUE INDICATOR HUE NUMBER

SHOE MOUNT

Summary of content (4 pages)

PAGE 1
® ® RGB RAINBOW RINGLIGHT USAGE INSTRUCTIONS Using Included Batteries: Flip the power switch [1] to the Battery position. Slide included Sony style NP-F750 batteries in by dropping each in to the top of the battery compartment and then sliding down until the battery snaps into place [2]. Note: The max run time for the Savage RGB Ringlight is approximately 90 minutes (daylight mode) or 150 minutes (RGB mode) at full power.
PAGE 2
® ® RGB RAINBOW RINGLIGHT USAGE INSTRUCTIONS SAVAGE LIGHT MANAGER APP Smart Phone App The Savage RGB Rainbow Ringlight can be controlled remotely using the free Savage “Light Manager” App available for download in both the Google Play Store and Apple App Store. To locate, search “Light Manager” and look for the icon pictured on the right of this page. COLOR WHEEL (1) With the Bluetooth setting on your phone enabled, press the light’s Power Switch on (either AC or DC power).
PAGE 3
® ® RGB RAINBOW RINGLIGHT MUSIC FUNCTION Your Savage RGB Rainbow Ringlight can be used to pulse with your music and audio files stored in your media library. The pulsing light will cycle through the various colors (rainbow effect) available and match the beat of the music or voices for audio recordings. It is not possible to specify a specific color in this function. Upon launch, the app will ask for access to your device’s media libraries.
PAGE 4
® ® RGB RAINBOW RINGLIGHT USAGE INSTRUCTIONS MANAGING BULBS Manage Bulbs CLICK LIST BUTTON FOR ANDROID: Name your ringlight: Tap the “List” icon at the top left of the app. A side bar will open up that lists “Manage Bulbs” Click the “Settings” icon next to “Manage Bulbs”. You should see the light listed. It will begin with “Magic….” Tap the wrench icon next to the listed light. A box will open to rename. Type in the name of your choice and select OK.