User's Manual

Wireless RF Gateway
(RFG-2000)
Quick Reference Guide
009- 0481-00
RFG-2000-00
6opyright © 2012 Savant Systems LLC, SAVANT and RacePoint Blueprint are trademarks of Savant Systems, LLC.
All brand names, product names and trademarks are the property of their respective owners.
Savant Systems, LLC reserves the right to change product specifications without notice.
Savant Confidential and Proprietary
021612
45 Perseverance Way, Hyannis, MA 02601 Phone [phone] Fax [phone] SavantSystems.com
The Savant Wireless RF Gateway (RFG-2000) Quick Reference Guide provides the
information necessary to setup and operate the Savant Select Remote. After the Savant
remotes are configured in RacePoint Blueprint, the remote will automatically find and
communicate (Synch) with the nearest RFG-2000.
Box Contents
(1) Savant Wireless RF Gateway (RFG-2000-xx)
(1) Sheet metal Mounting Bracket (071-0664-xx)
(1) 5V DC 2.5 AMP Universal Wall Unit with universal wall clips (025-0098-xx)
(2) 2.2mm x 8mm screws (039-0205-xx)
(1) Quick Reference Guide (this document)
Specifications
Environmental
Operating Temperature
32º to 104º F (0º to 40º C)
Operating Humidity
5% to 95% Non-condensing
Physical
Dimensions (L x. W x D)
1.75 in x 2.12 in x 0.95 in (4.44 cm x 5.38 cm x 2.41 cm)
Weight
0.4 oz (0.0113 kg)
Enclosure
High-impact molded ABS plastic
Power
Power
5V DC 7.5 AMP
Communication
Wireless
RF Transceiver, Frequency (Spectrum) - ISM Band
(2.4 GHz to 2.483 GHz)*
Regulatory
Safety and Emissions
CE/FCC Part 15/C-Tick*
RoHS
Compliant
1
SYNC
Press to Reset RFG-2000
2
RS232
RJ-45 used to receive and transmit data transmission
3
SYNC STAT
Green indicates the system has adequate power and is operating
normally.
Off indicates that the system is getting no power.
4
5 VDC
5V DC power connector used to supply power to the RFG-2000
Installation
1. Screw mast antenna to RFG-2000 box.
2. Screw mounting bracket at desired location.
3. Snap RFG into mounting bracket (See below).
4. Plug in 5V DC power supply.
For surface mounting, the RFG-2000 can be inserted into the sheet metal mounting bracket
that is shipped with the product. See below for installation instructions.
Additional Documentation
For more documentation, go to SavantSystems.com and navigate as follows:
>Dealer Login > Knowledge Base > Products
• Refer to RacePoint Blueprint™ Programming Guide
Compliance Information
This device is a composite device consisting of a Class B digital device and an intentional
radiator that complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Any changes or modifications of this product, not approved by manufacturer will void the
user’s authority to operate the equipment.
This device complies with Industry Canada license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna
of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To
reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
This radio transmitter (10052A-RFG2000) has been approved by Industry Canada to operate
with the antenna types listed below with the maximum permissible gain and required antenna
impedance for each antenna type indicated. Antenna types not included in this list, having a
gain greater than the maximum gain indicated for that type, are strictly prohibited for use with
this device.
Approved Antenna for the RFG-2000:
Antenna 2.4GHz Rubber Antenna (Part Number: 014-0098-00)
1
3
2
4