User's Manual
Wall Bracket Diagram
Wiring and Connections
RS-232 Wiring
Note:
CTS/RTS handshaking is supported for flow control based on the
profile used in the configuration.
RJ-45 to DB9 Adapters
Refer to the RS-232 Conversion to DB9 and RS-422/485 Pinout
Application Note located on the Savant Community for more
information on RJ-45 to DB9 adapters oered by Savant.
Note:
The SHC-2000 does not support RS-422/485.
IR Wiring
IR connections are made using 6-pin
Screw Down Plug-in Connectors supplied
with the Smart Host. The wire slips into
the hole and locks with a screw located
at the top of the connector.
Note:
While not shown in the diagram above, IR connections 4 to 6
follow the same wiring as 1 to 3.
Note:
While not shown in the diagram above, IR connections 4 to 6
follow the same wiring as 1 to 3.
IMPORTANT! IR Wiring Precautions
•
Ensure that all IR emitters are within 15 feet (4.6 meters) from the
controllers location.
•
Use of 3rd party flashing IR emitters with Talk Back is not
recommended. These types of emitters can draw voltage away from
the IR signal that can degrade IR performance.
GPIO Wiring
General Purpose Input/Outputs (GPIO)
are binary I/O ports used on Savant
controllers to trigger an action within the
system. Events can control a device,
such as turning on an amplifier (output)
or detecting a state change for a device
(input) to perform a workflow. Pin 2 is
used for input or output depending on
configuration.
GPIO Pull Down Resistor (PD) Usage
GPIO pins are configured as inputs and are pulled high to 12V while the
host is booting up. To make the GPIO signal low during a host reboot
and/or a power cycle, attach the GPIO 1 pin to the PD pin. The PD pin
is a 1K ohm pull down resistor (to signal ground)which keeps the GPIO
output below 0.8V during processor boot times.
Relay Wiring
Relay ports are used when a
device is controlled via a
normally open (NO) or normally
closed (NC) relay.
Refreshing the IP Connection
•
Reset Network Settings via Rear Panel Button
•
Cycle Power
•
Hot Plug the Ethernet (LAN) Connection
Regulatory
FCC (see RED portions)
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit
different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could void
the user's authority to operate this equipment.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm
between the radiator & your body.
SHC-2000-00 | 009-1326-00 | 150327
SHC-2000-00 | 009-1326-00 | 150327
45 Perseverance Way, Hyannis, MA 02601
Copyright © 2015 Savant Systems, LLC
2
of
2
savant.com | 508.683.2500