REVISION 01 DESCRIPTION OF CHANGE ECO-4581 Initial release MOUNTING GUIDELINES ST-675-SIAD-001 TAG FILENAME: 80500008R01.doc TITLE: DRAWING No: REV. MOUNTING GUIDELINES, ST-675-SIAD-001 TAG 805-00008-901 01 Drawing By: R.
ST-675-SIAD-001 Tag Mounting Guidelines © 2008 - Savi Technology Inc The Copyright in this document is vested in Savi Technology Inc. The contents of the document must not be reproduced (wholly or in part) used or disclosed without the prior written permission of Savi Technology Inc.
ST-675-SIAD-001 Tag Mounting Guidelines Contacts The material in this document is confidential and may be distributed only by authorized parties below (subject to confirmation).
ST-675-SIAD-001 Tag Mounting Guidelines Savi Technology Name Job Title Company Phone: # Email: address Name Job Title Company Phone: # Email: address Name Job Title Company Phone: # Email: address Name Job Title Company Phone: # Email: address 805-00008-901 Rev 01 MOUNTING GUIDELINES, ST-675-SIAD-001 TAG sheet 4 of 11
ST-675-SIAD-001 Tag Mounting Guidelines Table of Contents 1 INTRODUCTION ...........................................................................................6 1.1 1.2 1.3 2 COMPONENTS .............................................................................................7 2.1 2.1.1 2.1.2 2.2 2.2.1 3 PROJECT BACKGROUND .................................................................................... 6 PURPOSE .............................................................................
ST-675-SIAD-001 Tag Mounting Guidelines 1 INTRODUCTION This document provides general mounting guidelines for the modified 675 tag. The modified 675 tag is designed to fit non-ISO standard containers; specifically refrigeration containers. 1.1 Project Background The DLA has contracted Savi to develop a tracking and sensor solution for refrigerated containers. 1.2 Purpose The purpose for this Installation Document is to give general guidelines for mounting the modified 675 tag. 1.
ST-675-SIAD-001 Tag Mounting Guidelines 2 Components The section contains facts about each component that makes up the modified 675 tag. 2.1 Modified ST-675 Tag This section contains facts pertaining to the modified 675 tag. 2.1.1 Description The Savi SensorTagTM ST-675 is the latest innovation for tracking ISO shipping containers, providing new levels of door security monitoring, with active RFID intrusion and environmental sensors.
ST-675-SIAD-001 Tag Mounting Guidelines The Savi SensorTag ST-675 also monitors the environmental conditions inside the container. Any change in temperature is detected as the container moves through ports, terminals and key transportation routes worldwide. To monitor the acceptable environmental condition, the user sets the condition range within the Savi SensorTag.
ST-675-SIAD-001 Tag Mounting Guidelines 3 Installation of Tag The tag's mounting method is designed to be installed once for the duration of the containers service. The modified ST-675 tag can then be attached and removed rapidly for efficient tracking. There are several varying models of refrigeration containers, as such; various component placements will be employed. The following sequence should be followed for each new container model: 1. Determine best tag location 2. Surface Preparation 3.
ST-675-SIAD-001 Tag Mounting Guidelines For the antenna, some container models may not have adequate space between the edge of the door and the locking bar. In these instances, the antenna may be mounted on the far side of the locking bar. 3.2 Surface Preparation The tag shall be fastened to the container utilizing 3M 5952 family VHB tape; as such surface preparation is key to the success of the bond. Further information can be found at 3M’s website. 3.2.
ST-675-SIAD-001 Tag Mounting Guidelines 3.3 Tag Installation The Tag should be attached prior to cooling the container. This will allow for the fastest cure time. To fasten the tag to the container: 1. Remove red liner from 3M VHB tape to back of mounting plate. Make sure tape is located so it will make good contact with metal surface and NOT any rubber gasket material. 2. Press Tag half into position. 3.