Installation Guide Savi ST-675 Container Security Tag
Published February 2009 Part number 805-05830-901 Rev B Documentation for SaviTag ST-675 Copyright © 2009 Savi Technology, Inc. All rights reserved. Unpublished - rights reserved under the Copyright Laws of the United States. EchoPoint, Savi, Savi SensorTag, Savi SmartChain, Savi SmartStart, Savi Technology, Savi’s Nested Visibility, SaviTag, SmartChain, the EchoPoint Logo, and the Savi Logo are trademarks or registered trademarks of Savi Technology, Inc. in the United States and other countries.
Contents 1 Savi ST-675 Container Security Tag Description. . . . . . . . . . . . . 5 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Activating the Tag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Initializing the Tag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Placing the Tag for Best Performance . . . . . . . . . . . . . . . . . . . . . . . . . .
Savi ST-675 Container Security Tag Description The Savi ST-675 tag is an active RFID container security tag with intrusion and environmental sensors. The ST-675’s sensor arm detects the open/closed state of the shipping container door, and the intrusion light sensor monitors the amount of light entering the container. These intrusion sensors detect potential theft or tampering. The temperature, humidity, and shock sensors monitor environmental conditions to prevent spoilage or damage to goods.
Savi ST-675 Container Security Tag Installation Guide Figure 2: Top view Outside Inside Door Clamp Antenna Figure 3: Rear view Tag ID number Model number 6 USB port Battery compartment
Features Features • ISO 18000-7 compliant active RFID tag with environmental sensor capability • Sensors monitor security status and environmental conditions inside shipping container • Unique C-clamp, door-mounted design • Supports low frequency technology for more precise locating capabilities • FCC, HERO, ETSI, RoHS (Directive 2002/95/EC) certified Activating the Tag The tag is shipped in sleep mode. You must remove and re-insert the battery to wake up the tag.
Savi ST-675 Container Security Tag Installation Guide Correct battery orientation Turn to open Correct battery orientation Whenever a battery is inserted into a tag, the tag will emit 5 beeps. Then, if the tag emits a long (1/2 second beep), that means it has an internal sensor failure. Then, the tag will emit 2 short beeps to indicate adequate battery voltage or 3 short beeps if a fresh battery is required. Whenever a battery is inserted into a tag, the tag assumes that it is a fresh battery.
Initializing the Tag Improper O-ring exposed Proper O-ring hidden Turn cap until tight If the O-ring is not properly compressed by the cap, water leakage and damage may occur. Note: When the tag is not in use, disable the tag by removing, reversing, and re-inserting the battery. Store the battery at room temperature (50-80 °F or 10-27 °C ). Initializing the Tag Once you activate the tag, you can initialize it for immediate use. 1. Unplug the USB port cover. 2.
Savi ST-675 Container Security Tag Installation Guide USB cable 3. Refer to the Savi SmartChain Mobile User Guide or the Savi Smart- Chain WorkStation User Guide for instructions on the initialization process. Placing the Tag for Best Performance Savi Technology recommends that you mount the tag on a flat surface, with the tag aligned vertically.
Placing the Tag for Best Performance • Mounted on the container door higher than the closing and locking mechanism. The next figure shows an example of a security tag mounted on an ISO container door. Figure 4: Security tag mounted on an ISO container door Note: Make sure you clean the surface of the container or other asset before attaching the tag. The tag will have 400-foot (122m) read/write range to Savi SR-650 Fixed Readers.
Savi ST-675 Container Security Tag Installation Guide Mounting the Tag 1. Open the right door of the container. 2. Using both hands, push the C-clamp on the tag onto the edge of the left door until it is on as far as it can go. Left door outside view Left door inside view 3. Flip the door sensor arm to the right position so it can contact the inside of the right door when it closes. 4. Close the right door. The door sensor arm is now armed and in position to trigger if the container is opened.
Replacing the Battery Replacing the Battery The tag is equipped with non-volatile memory, which means stored data is not lost when you replace the battery. 1. Remove the battery cap. 2. Remove the discharged battery from its compartment. For more information, see “Activating the Tag” on page 7. The lithium battery can be harmful to the environment. Follow current procedures for safely disposing of lithium batteries. The battery cannot be reused or recharged. 3. Install a 3.
Savi ST-675 Container Security Tag Installation Guide Contacting Savi Support If you cannot find the information you need, contact Savi Support Services. • Check http://supportcenter.savi.com for contact information. • Send an email to help@savi.com. • Call 1-888-994-SAVI (North America only) or 1-650-316-4760 between 5 a.m. and 5 p.m. Pacific time.
Specifications Specifications Model Numbers ST-675-030: Container security tag ST-675-030-NSN: Container security tag with label Physical Characteristics Rear case: 4.7 in. (12 cm) x 4.5 in. (11.4 cm) x 1.5 in. (3.8 cm) Front case: 4.6 in. (11.6 cm) x 3.2 in. (8.1 cm) x 0.5 in. (1.2 cm) C-clamp: 4.7 in. (12 cm) x 5.2 in. (13.3 cm) x 2 in.
Savi ST-675 Container Security Tag Installation Guide Digital Sensor memory: 32 Kbytes on-board non-volatile memory Database memory: 128 Kbytes on-board non-volatile memory Wired interface: USB 1.1, USB 2.0 Mounting C-clamp: Clamps easily onto shipping container left door edge (frame) - C-clamp to left door, sensor arm under right side for monitoring door closure status. Tag can be mounted anywhere on the edge of the left-hand container rectangular doorframe measuring 2 in. (50 mm) x 4 in. (100 mm).