Installation Guide Savi Tag ST-696-001 ISO Container Door Tag with GPS/GPRS and Sensors Savi Tag ST-696-001 ISO Container Door Tag with GPRS/GPS and Sensors Installation Guide 1
Published December 2007 Part number 805-02001-001 Rev 01 Documentation for Savi Tag ST-696-001 ISO Container Door Tag with GPS/GPRS and Sensors Copyright ©2007 Savi Technology, Inc. All rights reserved. Unpublished rights reserved under the Copyright Laws of the United States. EchoPoint, Savi, Savi Tag, Savi SmartChain, Savi SmartStart, Savi Technology, SaviTag, SmartChain, the EchoPoint Logo, the Savi Logo, the UDAP Logo, and UDAP are trademarks or registered trademarks of Savi Technology, Inc.
Contents About Savi Tag ST-696-001 ISO Container Door Tag with GPS/GPRS and Sensors Features . . . 4 Description . . . 5 For More Information . . . 7 Guides to Read . . . 7 Contacting Savi Global Support Services . . . 7 Installing Savi Sensor Tag ST-696-001 ISO Container Door Tag with GPS/GPRS and Sensors Required Tools and Materials . . . 8 Commissioning the Tag with SaviTag Write Cable STA-1030 . . . 8 Replacing the Battery . . . 10 Tag Placement . . .
About Savi Sensor Tag ST-696-001 ISO Container Door Tag 1 Savi® Tag ST-696-001 ISO Container Door Tag with GPS/GPRS and Sensors is a high performance active RFID tag that works with Savi software to track and monitor the security status of containers as they move through the global supply chain. This device is fully compatible with fixed and portable Savi readers and features up to 300 feet (91.44 meters) of omni-directional line-of-sight range.
Description Figure 1-1 Savi Tag ST-696-001 ISO Container Door Tag Savi Tag ST-696-001 ISO Container Door Tag with GPRS/GPS and Sensors Installation Guide 5
Intrusion Detection Sensors The ST-696-001 tags include door and light sensors. The door sensor monitors the amount of pressure between the door and the device. If the door is open and the device has not been electronically unsealed, the device sends a message to the monitoring software indicating that the device has been tampered. It also writes the time and date of the tamper to an event log. The device also includes a light sensor that triggers an alarm if light is detected inside the container.
For More Information Guides to Read For information about using: ◆ Signposts, see the Savi Signpost SP-65X Series Installation Guide ◆ Fixed readers, see the Savi Fixed Reader SR-650-101 Installation Guide ◆ Mobile readers, see the Savi Mobile Reader SMR-650 for the Intermec 751G/A Mobile Computer and PC User Guide Contacting Savi Global Support Services If you cannot find the information you need, contact Savi Global Support Services. ◆ Check www.savi.com/services/su.contact.
Installing Savi Tag ST-696-001 ISO Container Door Tag Required Tools and Materials Before you begin installation, make sure the following materials are available: ◆ Savi Tag ST-696-001 ISO Container Door Tag with GPS/GPRS ◆ SaviTag Write Cable STA-1030 ◆ Wall Adapter (provided) Tag commissioning with SaviTag Write Cable STA-1030 You can commission Savi Tag ST-696-001 ISO Container Door Tag using SaviTag Write Cable STA-1030.
1. Connect SaviTag Write Cable STA-1030 to an available serial port on the host computer. 2. Locate the tag commissioning port on the Savi ST-696-001 ISO Container Door Tag. 3. Unplug the rubber cap covering the port. 4. Insert SaviTag Write Cable STA-1030, with the LED up, into the Tag ST-696-001 commissioning port. Start the tag commissioning application. The LED is lit when the application writes data to the tag.
Charging the Tag Battery Savi Tag ST-696-001 ISO Container Door Tag is equipped with non-volatile memory, which means stored data is not lost when the battery is fully depleted. 1. Using a coin or flat-head screwdriver, turn the charging plug cover counterclockwise. When removing the charging plug cover, hold on to it to avoid dropping it. 2. Plug wall adapter (provided) into the standard AC outlet. 3. Plug the wall adapters’ plug into the power jack on the tag.
Tag Placement Savi Technology recommends that you fit the Savi Tag ST-696-001 ISO Container Door Tag above the door bracket and on the lefthand door of the container. The recommended mounting location for the tag is shown in the following photos. 1. Open the right door of the container. 2. Align the device with the bracket on the right door, if possible. 3. Using both hands, secure the device on the left door until it is flush. This is a view from inside the container.
4. Move the door sensor to the left and ensure that the lever is fully extended before closing the container door. This is a side view of the device mounted on the left door. This is a view of the outside of the container 5. Close the right door. This is a view of the tag on the container with both doors closed. 6. Seal the tag using the software on your mobile device. The door sensor recognizes when the right door is closed and when the container is dark. 7.
Savi Tag ST-696-001 ISO Container Door A Tag Specifications Specification Description Physical characteristics Tag Height: 10 inches Width: 6 inches Depth: 5 inches Total weight of tag 2 lb 12 ounces (1.3 Kg) Environment Temperature: -20ºC to +60ºC) operating; -40ºC to +85ºC storage Humidity: 100% non-condensing Altitude: Maximum altitude = 40,000 feet (12,192m); MIL-STD-810E Method 500.3, Procedure I RFID receiver/transmitter Ultra High Frequency transceiver: Frequency: 433.
Specification Description LF receiver (downlink) Low Frequency receiver (downlink) Frequency: 123 KHz Modulation: ASK On-Off Keying Data rate: Average 1.6 Kbps, 50% duty cycle Data coding: Pulse Width Modulation Communication range: Up to 4 feet (1.22 meters) from Savi MobileReader SMR-650P110 and SMR-650P-111 or Savi Mobile Reader SMR-650-212 Up to 12 feet (3.66 meters) from Savi Signpost (models SP-600-xxx and SP-65x-xxx) Air protocol: Savi EchoPoint Air Protocol 1.
Specification Description Hardware compatibility ✦ Savi Mobile Reader SMR650P (model SMR-650P-xxx) ✦ Savi Mobile Reader SMR-650 (models SMR-650-xxx) ✦ Savi Fixed Reader SR-650 ✦ Savi Signpost SP 65x series Antenna Internal loop antenna Shock and vibration Shock: MIL-STD-810E Mechanical Shock, Transit Drop Methods 516.4 Vibration: MIL-STD-810E Method 514.4, Category 10 Loose cargo test: MIL-STD-810F Method 514.
Specification Description Sensors Door sensor: Senses the right side of the container door in the closed or open position Light sensor: Senses light coming through the door Temperature sensor: Integrated temperature takes readings every five minutes (default; use Savi software to adjust settings). Mounted in its own compartment to isolate it from other circuit boards Humidity sensor: Integrated humidity sensor takes readings every five minutes (default; use Savi software to adjust settings).
