Mobile Security Parent (ST-900-CP) User Guide Manufacturing plant : Manufacturer : Dae Kyung Philippines., Inc. Savi Technology, Inc. Lot No.
NOTICE This manual, software and electronic circuitry are copyrighted. All rights reserved. Under the copyright laws, this manual, software and electronic circuitry may not be copied, in whole or in part without written prior consent of Savi Technology, Inc.. All information provided in this document is carefully prepared and offered in good faith as a guide in the installation, use and servicing of our products.
IMPORTANT SAFETY INFORMATION RF EXPOSURE STATEMENT Your Transmitter contains a radio frequency transmitter. When physical damage or un-lock is the transmitter sends our RF signals. To comply with FCC RF exposure compliance requirements, a separation distance of at least 11.81 inches (30 cm) must be maintained between the antenna of this transmitter and all persons, during normal operation.
Table of Contents About the Savi Security Sensor Family .......................................................................................... 5 Introduction .................................................................................................................................. 5 What’s New? ............................................................................................................................... 5 Sensor Family and Components ..............................................
About the Savi Security Sensor Family Introduction The Savi Security Sensor Family provides users security and visibility while tracking high-value assets and cargo throughout their global supply chains. Savi Tracking is designed to provide users a seamless and complete view of the location and security status of in-transit assets and cargo.
Sensor Family and Components Sensor Models Mobile Security Parent Model No.
Specifications Mobile Security Parent, ST-900-CP PHYSICAL LxWxH 88 mm x 46 mm x 168 mm Standard Cable Length 300 mm Weight 0.36 kg -30°C to +50°C Operating -40°C tp +70°C Non-Operating Humidity 95% RH @ 50°C Non-Condensing Vibration and Shock U.S.
Using the Sensors Turning on the Mobile Security Parents and/or Child Sensors For the Mobile Security Parent and Child Sensors: To turn on the Mobile Security Parent and Child Sensors, pull the plungers up. For the Vehicle Security Gateway: Turn on the truck or vehicle ignition to turn on the sensors. Charging the Mobile Security Parent The Mobile Security Parent is rechargeable with a USB cable.
LED Light Patterns All Savi Security Sensors include a two-color red/green LED indicator that details various status conditions. These LED patterns are defined below and should be used to assist in system operation and troubleshooting as necessary.
TCP Connection Good Communicating with Server Searching for Child Paired Child Located Ready to Arm/No GPS Fix Ready to Arm/GPS Fix Security Tamper Savi Security Sensor Family Copyright© 2016 10
Child Sensor LED Patterns Initialization Low Battery Alert Communicating with Parent Searching for Parent Paired Parent Located Ready to Arm/Parent Linked Security Tamper Savi Security Sensor Family Copyright© 2016 11
Journeys with a Mobile Security Parent Only Creating the Journey 1. Log into Savi Tracking. 2. Create a Journey by performing the following steps: a. Select an Owner and Corridor from the drop-down list. b. Enter the Asset Number. c. Enter the Mobile Security Parent serial number in the “Tracking Tag” field. d. Click “Begin Journey” to indicate you are ready to arm tags.
Arming the Mobile Security Parent 1. Turn on the sensor. 2. Loop the pin and cable through lock or door on container or vehicle. 3. Push pin down into the plunger firmly until it clicks into place. Then push the plunger down to arm and lock the sensor.
4. The green bullet will display in Savi Tracking to show that the Mobile Security Parent is armed and ready. 5. Once the Mobile Security Parent is armed, select “Depart Journey” from the drop-down list.
6. The Current Status of the journey will change to “Secure Transit”.
Journeys with One or More Mobile Security Child Sensors Creating the Journey 1. Log into Savi Tracking. 2. Create a Journey by performing the following steps: a. Select an Owner and Corridor from the list. b. Enter the Asset Number. It is possible to either work with a registered asset or with a non-registered asset. If a registered asset is selected from the drop-down list, then the Tracking Tag field will automatically be filled in with the Vehicle Security Gateway serial number. c.
e. When done, click Begin Journey. Arming the Mobile Security Parent and Child 1. Turn on the sensors; make sure the Parent and Child are in close proximity to each other. Verify LED lights for successful pairing. 2. To arm the both the Mobile Security Parent and the Mobile Security Child, loop the pin and cable through lock or door on container or vehicle.
3. Push pin down into the plunger firmly until it clicks into place. Then push the plunger down to arm and lock the sensor. 4. The green bullets will display in Savi Tracking to show that the Mobile Security Child Sensors are armed and ready.
5. Once the Child Sensors are armed, select “Depart Journey” from the drop-down list. 6. The Current Status of the journey will change to “Secure Transit.
Troubleshooting Replacing a Child Sensor For various reason, it may be necessary to replace a Child Sensor on a journey, for example because: The child sensor isn’t pairing with the parent sensor The child sensor isn’t arming The Child sensor has a low battery To replace a Child Sensor on a journey, perform the following steps: 1. Search for the journey using the Journey screen.
2. Click on the journey to display the journey details. 3. Click on Full Details to display the full journey details.
4. Click pencil symbol to edit the journey: 5. Delete the sensor that needs to be replaced by clicking on the “X” symbol next to it.
6. Add a new sensor by start typing the Child Sensor ID and selecting it from the drop-down list. 7.
Maintenance Cleaning Instructions TBD Replacing a Cable TBD Storing the Sensors TBD Copyright © 2016 Savi Technology. All rights reserved. Printed in the United States of America. All trademarks used are properties of their respective owners. This document is proprietary to Savi Technology. Do not reproduce, use or disclose without permission.
Savi Security Sensor Family Copyright© 2016 25
