Printer/Scanner Kit Type 1232 Operating Instructions Printer Reference 2 1 Setting Up the Printer Driver and Canceling a Print Job 2 Uninstalling the Printer Driver 3 Printing with the Control Panel 4 Troubleshooting 5 Using the Control Panel 6 Appendix For safe and correct use of this machine, please be sure to read the Safety Information in the “General Settings Guide” before you use it.
Introduction This manual describes detailed instructions on the operation and notes about the use of this machine. To get maximum versatility from this machine all operators are requested to read this manual carefully and follow the instructions. Please keep this manual in a handy place near the machine. Important Contents of this manual are subject to change without prior notice.
TABLE OF CONTENTS Manuals for This Machine ..................................................................................... 1 How to Read This Manual ..................................................................................... 2 1. Setting Up the Printer Driver and Canceling a Print Job Accessing the Printer Properties ......................................................................... 3 Windows 95/98/Me - Accessing the Printer Properties ..............................................
5. Using the Control Panel Adjusting Printer Features ................................................................................. 43 Printer Features Menu .............................................................................................43 Accessing the Printer Features ................................................................................44 Exiting from the Printer Features .............................................................................
Manuals for This Machine The following manuals describe the operational procedures and maintenance of this machine. To enhance safe and efficient operation of this machine, all users should read and follow the instructions carefully. ❖ General Settings Guide Provides an overview of the machine. This manual introduces the functions of the machine. It also introduces the options that allow you to use additional functions and describes how to access the system user tools to make the machine easier to use.
How to Read This Manual Symbols In this manual, the following symbols are used: R WARNING: This symbol indicates a potentially hazardous situation which, if instructions are not followed, could result in death or serious injury. R CAUTION: This symbol indicates a potentially hazardous situation which, if instructions are not followed, may result in minor or moderate injury or damage to property. * The statements above are notes for your safety.
1. Setting Up the Printer Driver and Canceling a Print Job Accessing the Printer Properties Windows 95/98/Me - Accessing the Printer Properties Changing the default machine settings A Click [Start] on the taskbar, point to [Settings], and then click [Printers]. The [Printers] window appears. B Click the icon of the machine whose default settings you want to change. C On the [File] menu, click [Properties]. The [Printer Properties] dialog box appears. D Make any settings you require, and then click [OK].
Setting Up the Printer Driver and Canceling a Print Job Windows 2000/XP - Accessing the Printer Properties Changing the default machine settings - Printer Properties 1 Limitation ❒ Changing the setting of the machine requires Manage Printers permission. Members of the Administrators and Power Users groups have Manage Printers permission by default. When you set up options, log on using an account that has Manage Printers permission.
Accessing the Printer Properties Note ❒ In Windows XP Professional, access the [Printers and Faxes] window from [Start] on the taskbar. ❒ In Windows XP Home Edition, access the [Printers and Faxes] window by clicking [Control Panel] from [Start] on the taskbar. Then click [Printers and Other Hardware], and then [Printers and Faxes]. 1 B Click the icon of the machine whose default settings you want to change. C On the [File] menu, click [Printing Preferences...].
Setting Up the Printer Driver and Canceling a Print Job Windows NT 4.0 - Accessing the Printer Properties Changing the default machine settings - Printer Properties 1 Limitation ❒ Changing the setting of the machine requires Full Control access permission. Members of Administrators, Server Operators, Print Operators, and Power Users groups have Full Control permission by default. When you set up options, log on using an account that has Full Control permission.
Accessing the Printer Properties Making machine settings from an application To make the machine settings for a specific application, open the [Printer Properties] dialog box from that application. The following example describes how to make settings for the WordPad application that comes with Windows NT 4.0. 1 Note ❒ The actual procedures you should follow to open the [Printer Properties] dialog box may vary depending on the application.
Setting Up the Printer Driver and Canceling a Print Job D From the [Paper:] box, select the paper size. E Make any settings you require, and then click [OK]. 1 Setting up for printing from an application A Open the file you want to print. B On the [File] menu, click [Print]. The [Printer Features] dialog box appears. C Make sure that the machine is selected in the [Printer:] box. D Make any settings you require, and then click [Print] to start printing.
Canceling a Print Job Canceling a Print Job Windows - Canceling a Print Job 1 A Double-click the printer icon on the Windows taskbar. A window appears, showing all the print jobs that are currently queuing to be printed. Check the current status of the job you want to cancel. B Select the name of the job you want to cancel. C On the [Document] menu, click [Cancel Printing]. Note ❒ In Windows XP, click [Cancel] on the [Document] menu. ❒ In Windows 95/98/Me, 2000 or NT 4.
Setting Up the Printer Driver and Canceling a Print Job Macintosh - Canceling a Print Job A Double-click the printer icon on the desktop. 1 A window appears, showing all the print jobs that are currently queuing to be printed. Check the current status of the job you want to cancel. Note ❒ In Mac OS X, start Print Center. B Select the name of the job you want to cancel. C Click the pause icon, and then click the trash icon. D Press the {Printer}} key on the machine's control panel.
2. Uninstalling the Printer Driver Uninstalling the Printer Driver This section describes how to uninstall the printer drivers. Actual procedures may vary depending on the operating system. Follow the procedures below as appropriate. Windows 95/98/Me - Uninstalling the Printer Driver A Close all the applications that are currently running. B Click [Start] on the taskbar, point to [Settings], and then click [Printers]. The [Printers] window appears. C Click the icon of the machine you want to remove.
Uninstalling the Printer Driver D On the [File] menu, click [Delete]. A confirmation dialog box appears. E Click [Yes] to uninstall the printer driver. Note ❒ You can also uninstall the printer driver using the following procedure. 2 • Windows 2000 A In the [Printers] window, click [Server Properties] on the [File] menu to display the [Print Server Properties] window. B On the [Drivers] tab, click the driver you want to remove, and then click [Remove]. C Click [Yes]. D Click [OK].
Uninstalling the Printer Driver Mac OS - Uninstalling the PostScript 3 Printer Driver A Drag the “AdobePS” file from the [Extensions] folder in [System Folder] to [Trash]. B Drag the PPD file and plug-in file from the [Printer Descriptions] folder in the [Extensions] folder in [System Folder] to [Trash]. 2 Mac OS X - Uninstalling the PostScript 3 Printer Driver A Run Print Center. B Select the printer driver you want to uninstall in the Printer List window, and then click [Delete].
Uninstalling the Printer Driver 2 14
3. Printing with the Control Panel Sample Print Use this function to print only the first set of a multiple-set print job. After you have checked the result, the remaining sets can be printed or canceled from the machine's control panel. This can help in avoiding large amounts of misprints in case of mistakes in the content or in the print settings. Note ❒ If the application has a collate option, make sure that it is not selected before sending a print job.
Printing with the Control Panel C On the machine's control panel, press the {Printer}} key to display the Printer Screen. 3 ZFFH371E D Press [View Sample Print jobs]. A list of the sample print files stored in the machine is displayed. The following will also be displayed: • User ID: The User ID set up by the printer driver. • Date/Time : The date and time when the job was sent from the computer. • Qty.: The number of remaining sets. E Select the file you want to print by pressing on it.
Sample Print G Enter the new number of sets using the number keys and press [OK]. 3 ZFFH361E The screen returns to the file list screen. Note ❒ You can enter up to 999 sets. ❒ Press [Clear] to correct any entry mistakes. ❒ If you want to cancel changing the set quantity, press [Cancel]. H Press [Print]. The print confirmation screen is displayed. I Press [Yes]. The remaining sets are printed. Note ❒ Press [No] to cancel printing. ❒ When printing is completed, the stored file will be deleted.
Printing with the Control Panel Deleting a Sample Print File If you are not satisfied with the sample printout, you can delete the sample print file, revise it and print it again until the settings are fine. A Press the {Printer}} key to display the Printer Screen. 3 ZFFH371E B Press [View Sample Print jobs]. A list of the sample print files stored in the machine is displayed. C Select the file you want to delete by pressing on it. Note ❒ Press [U UPrev.] or [T TNext] to scroll through the list.
Sample Print Checking the Error Log If a file could not be stored in the machine, you can check the error log on the control panel. Limitation ❒ The error log displays only the 20 most recent entries. If the power is turned off, the log will be deleted. A Press the {Printer}} key to display the Printer Screen. 3 ZFFH371E B Press [View Sample Print jobs]. C Press [Show Error Log]. D Press [UUPrev.] or [TTNext] to scroll the error files. Press [Exit] after checking the log.
Printing with the Control Panel Locked Print Use this function to maintain privacy when printing confidential documents on the machine over a shared network. Usually, it is possible to print data by using the control panel once the data is stored in this machine. When using Locked Print, it will not be possible to print unless a password is entered on the machine's control panel. Your confidential documents will be safe from viewing by other people.
Locked Print C On the machine's control panel, press the {Printer}} key to display the Printer Screen. 3 ZFFH371E D Press [View Locked Print jobs]. A list of the locked print files stored in the machine is displayed. The following will be also be displayed: • User ID: The User ID set up by the printer driver. • Date/Time: The date and time when the job was sent from the computer. • Qty: The number of remaining sets. E Select the file you want to print by pressing on it. Note ❒ Press [U UPrev.
Printing with the Control Panel G Enter the password using the number keys and press [OK]. The print confirmation screen is displayed. Note ❒ A confirmation screen will appear when the password has not been entered correctly. Press [OK] to enter the password again. H Press [Yes]. The locked file is printed. Note ❒ Press [No] to cancel printing. ❒ If printing is stopped by pressing [Job Reset] after printing has started, the file will be deleted.
Locked Print D Press [Delete]. The password screen is displayed. E Enter the password using the number keys and press [OK]. The delete confirmation screen is displayed. 3 F Press [Yes]. After the file has been deleted, the screen returns to the file list screen. Note ❒ If you do not want to delete the file, press [No]. ❒ If you forget your password, set [Display Password with Stored File] to “ON” on the [Key Operator Tools] tab of the System Settings screen.
Printing with the Control Panel B Select [View Locked Print jobs]. C Press [Show Error Log]. 3 D Press [UUPrev.] or [TTNext] to scroll the error files. Press [Exit] after checking the log. You will then return to the file list screen. Note ❒ For printing files that appear in the error log, resend them after stored files in the machine have been printed or deleted.
Accessing the Document Server Accessing the Document Server The Document Server enables you to save documents in the machine's built-in hard disk to edit and print as you want. Reference For more information about Document Server functions, see the General Settings Guide. For information about how to access to Document Server from a client, see the printer driver's Help.
Printing with the Control Panel 3 26
4. Troubleshooting Error & Status Messages on the Display Panel ❖ Status Messages Messages/Second messages Status Hex Dump Mode The machine receives data in hexadecimal numbers in Hex Dump mode. Turn off the machine after printing, and then turn back on. Offline The machine is offline. Set the machine online by pressing [Online] on the display panel to start printing. Please Wait The machine is initializing the development unit. Wait for a while. Printing... The machine is making prints.
Troubleshooting Messages/Second messages Driver setting error. (Memory) Description Solution There is an error in the downloaded font(s). Reset the parameter for downloading fonts. Insufficient memory or memory settings for the printer driver may not match memory actually installed. Specify correct memory capacity in the [Change Accessories...] option in the RPCS™ printer driver's print settings tab. To print the image correctly, increase memory capacity, or reduce resolution image.
Error & Status Messages on the Display Panel Messages/Second messages Following output tray is full. ### Description Solution The indicated output tray is full. Remove the paper. Note ❒ “###” in the message represents a output tray. HDD has a problem. An error has occurred in the hard disk drive. Turn off the main power switch, and on. If the message appears again, contact your sales or service representative. HDD has not been installed.
Troubleshooting Messages/Second messages Description Solution Paper size and type are mismatched. Specified paper size and paper type are not loaded in the paper feed tray. Change the settings to continue the current job, or press [Reset] to cancel the job. Parallel I/F board has a prob- An error has occurred in the lem. parallel interface board. 4 Contact your sales or service representative. Print overrun. The image data has been Increase memory capacity.
Error & Status Messages on the Display Panel Messages/Second messages Description *** No toner. Replace Toner Cartridge. The indicated color toner has almost run out. Solution Replace the toner cartridge with a new one. Note ❒ “***” in the message represents the color: Black, Yellow, Magenta, or Cyan. DToner is almost empty. The toner has almost run out. Replace the toner cartridge with a new one. Tray ### has a problem. Turn Main Power Switch off then on.
Troubleshooting ❖ *1 Input Tray: Name Name Description Tray X Name of installed paper tray (X is the number of tray.
Error & Status Messages on the Display Panel ❖ *3 Input Tray: Status Status Description Normal NoTray There is no paper tray PaperEnd There is no paper in the paper tray ❖ *4 Output Tray: Name Name Description Internal Tray 1 Internal Tray 1 Internal Tray 2 Internal Tray 2 Shift Tray Shift Tray Finisher Tray Finisher Tray (Finisher 500) Finisher Proof Tray Finisher Proof Tray (Finisher 1000) Finisher Shift Tray Finisher Shift Tray (Finisher 1000) 4 ❖ *5 Output Tray: Status Status
Troubleshooting Machine Does Not Print Possible Cause Is the power on? Solutions Confirm the cable is securely plugged into the power outlet and the machine. Turn on the main power switch. 4 Is the machine online? If not, press [Online] on the display panel. Does the printer function status indicator stay red? If so, check the error message on the display panel and take the required action.
Machine Does Not Print Possible Cause Is the Data In indicator blinking or lit after starting the print job? Solutions If not, the data is not being sent to the machine. ❖ When the machine is connected to the computer using the interface cable Confirm that the machine port settings are correct. For a parallel port connection, port LPT1 or LPT2 should be set. • Windows 95/98/Me A Click [Start], point to [Settings], and then click [Printers]. B Click the icon of the machine.
Troubleshooting Other Printing Problems Status Possible Causes, Descriptions, and Solutions The print on the entire page is faded. If “Toner Saver” is selected in the [Print Quality] tab on the printer driver tab, the entire page will be faded when printed. See the printer driver's Help. The print smudges. The settings have not been set to thick paper when printing on thick paper. • PCL 5c/PostScript 3 Select “Thick” for [Type] on the printer driver's [Paper] tab.
Other Printing Problems Status Possible Causes, Descriptions, and Solutions When using Windows 95/98/Me, Windows 2000/XP, or Windows NT4.0, either combined printing or bookbind print does not come out as expected. Make sure the application's paper size and orientation settings match those of the printer driver. If a different paper size and orientation are set, select the same size and orientation. When using Windows 95/98/Me, Windows 2000/XP, or Windows NT 4.
Troubleshooting Status Color documents are printed in black and white. Possible Causes, Descriptions, and Solutions The printer driver is not set up for color printing. • PCL 5c/PostScript 3 Select “Color” for [Color/Black and White] on the printer driver's [Setup] tab. • RPCS™ Select “Color” for [Color/Black and White] on the printer driver's [Print Settings] tab. See the printer driver's Help. Some applications print color files in black and white. Fine dot pattern does not print.
Other Printing Problems Status Possible Causes, Descriptions, and Solutions It takes too much time to resume printing. The data is so large or complex that it takes time to process. If the Data In indicator is blinking, data is being processed. Just wait until printing resumes. The machine was in Energy Saver mode. To resume from Energy Saver mode, it has to warm up, and this takes time. To disable Energy Saver mode, select "Off" for "Energy Saver 1" in the System Settings menu.
Troubleshooting Status Possible Causes, Descriptions, and Solutions Images are printed in the wrong orientation. The feed direction you selected and the feed direction selected in the printer driver's Option Setup of the printer driver might not be the same. Make the proper settings. See the printer driver's Help. The printed image With certain functions, such as enlargement and reduction, the layout of is different the im- the image might be different to that on the computer display.
Auto Color Calibration Auto Color Calibration This function is used for adjusting the balance of yellow, magenta (red), cyan (blue), and black when certain colors are too strong or when the color of the print is different from the screen. Note ❒ If “D Toner is almost empty.” is shown on the display panel, the test pattern cannot be printed. A Press the {User Tools/Counter/Inquiry}} key on the control panel. 4 ZFFH801E B Press [Maintenance]. C Press [Auto Color Calibration].
Troubleshooting F Press [Start Printing]. A test pattern will be printed, and the message “Place Test Pattern on exposure glass correctly, then press [Start Scanning]” appears. Note ❒ The test pattern will be printed on A4K, B4JISL, A3L, 11”x17”L or 8/”x11”K. One of the above paper sizes should be loaded on the paper feed tray. ❒ Printing the test pattern does not advance the counter. G Place the test pattern on the exposure glass, and press [Start Scanning].
5. Using the Control Panel Though the factory default settings of the machine are suitable for most printing jobs, the “Printer Features” gives you access to a number of settings that control basic printer operations. “Printer Features” settings you make are retained even when you turn off the machine. Reference For more information about the copier features and the system settings, see the Copy Reference and the General Settings Guide.
Using the Control Panel Category System⇒ p.47 Function menu Print Error Report Auto Continue Memory Overflow Sub Paper Size Page Size Duplex Job Separation Resolution PCL PS Toner Saving Host Interface ⇒ p.50 I/O Buffer I/O Timeout 5 PCL Menu⇒ p.50 Orientation Form Lines Font Source Font Number Point Size Font Pitch Symbol Set Extend A4 Width Accessing the Printer Features A Press the {User Tools/Counter/Inquiry}} key on the control panel. B Press [Printer Features].
Adjusting Printer Features Exiting from the Printer Features A After changing the Printer Features, press [Exit] to return to the User Tools/Counter/Inquiry menu. B Press [Exit]. Note ❒ You can also exit from the User Tools/Counter/Inquiry menu by pressing the {User Tools/Counter/Inquiry} } key.
Using the Control Panel Printer Features Parameters Paper Input Menu Bypass Paper Size Description The paper size for the bypass tray. For more information about paper sizes that can be set in the bypass tray, see the General Settings Guide. Note ❒ Default: A4 (Metric version), 11 × 8/ (Inch version) List/Test Print 5 Menu Config. Page Description You can print the current configuration of the machine. Reference See p.52 “Machine Condition” for printing a configuration page.
Printer Features Parameters The table below lists the menus that can be protected at level 1 or 2. Menu Level 1 Level 2 Paper Size Settings × ❍ Adjustment/Management ❍ ❍ System Settings ❍ ❍ Interface Settings ❍ ❍ Program × ❍ PCL Menu ❍ ❍ Language ❍ ❍ ❍: Protected ×: Not protected Note ❒ You can also use SmartNetMonitor for Admin to protect menus. To do so, you must set an access code on the machine beforehand.
Using the Control Panel Menu Memory Overflow Description You can select whether the memory overflow error report should be printed. • Not Print • Error Report Note ❒ Default: Not Print Sub Paper Size You can enable the “Auto Substitute Paper Size (A4↔LT)” feature. • Off • Auto Note ❒ Default: Off Page Size You can select the default paper size.
Printer Features Parameters Menu Duplex Description You can select whether you want to print on both sides of each page. • Off • Short Edge Bind • Long Edge Bind Note ❒ Default: Off ❒ This menu appears only when the optional Duplex unit is installed. Job Separation You can enable “Job Separation”. • Off • On Note ❒ Default: Off 5 ❒ This menu appears only when the optional shift sort tray is installed. Resolution You can set the print resolution in dots per inch.
Using the Control Panel Host Interface Menu I/O Buffer Description You can set the size of the I/O Buffer. Normally it is not necessary to change this setting. • 128 KB • 256 KB • 512 KB Note ❒ Default: 128 KB I/O Timeout You can set how many seconds the machine should wait before ending a print job. If data from another port often arrives in the middle of the print job, you should increase the timeout value.
Printer Features Parameters Menu Font Number Description You can set the ID of the default font you want to use. • 0 to 50 by 1 Note ❒ Default: 0 Point Size You can set the point size you want to use for the selected font. • 4.00 to 999.75 by 0.25 Note ❒ Default: 12.00 ❒ This setting is effective only for a variable-space font. Font Pitch You can set the number of characters per inch you want to use for the selected font. • 0.44 to 99.99 by 0.01 Note 5 ❒ Default: 10.
Using the Control Panel Machine Condition We recommend that you print the configuration page and check the machine's settings before changing them. Printing the Configuration Page A Press the {User Tools/Counter/Inquiry}} key on the control panel. The User Tools/Counter/Inquiry menu appears. B Press [Printer Features]. The Printer Features menu appears. C Press the [List/Test Print] tab. The following screen appears on the display panel. 5 D Press [Config. Page]. The configuration page is printed.
6. Appendix Staple The following table shows the staple positions. Note ❒ Stapling depends on paper size, paper type, number of pages and feed direction. Paper orientation Print data on the machine direction Staple position Finisher 500 Finisher 1000 Vertical Horizontal Vertical Horizontal ZFFH999E Reference • For paper sizes and maximum numbers of sheets available for stapling, see “Staple”, Copy Reference. • For printing method, see the printer driver's Help.
Appendix Note ❒ When the finisher is installed and stapling is specified for a job, the job will be delivered to the Finisher Shift Tray regardless of the output tray specified. ❒ If you cannot make staple settings even with the finisher installed, options may not be set up correctly on the printer driver. Correct option settings in the printer driver. For details, see the Help of the printer driver. ❒ When duplex printing is specified, adjust staple positions to the binding direction.
Staple • If there are inconsistencies between the duplex folding direction and the staple printing folding location during duplex printing. • If paper sizes are mixed when a different paper size is specified during a print job. • When staples have run out. • When feeding paper from the optional bypass tray.
Appendix Spool Printing Spool Printing allows print jobs transferred from a computer to be temporarily stored, and then prints them after they are transferred. This shortens printing time as it maximizes printer efficiency. Important ❒ During Spool Printing, the hard disk is accessed and the Data-In indicator blinks. Turning off the computer or machine during Spool Printing can damage the hard disk. Also, if the computer or machine is turned off during Spool Printing, spooled jobs will be deleted.
Spool Printing - Setting Spool Printing Spool Printing can be set using telnet or a web browser. • Using a web browser Click ”Configuration”, and then “General”. Set “Spool Printing”to “Enable”. See Network Printing Guide or Help for more information. • Using telnet Enter “spoolsw spool on” to set Spool Printing. See Network Printing Guide for more information about telnet.
Appendix Specifications This section contains the electrical and hardware specifications for the machine including information about the options. Component Specification Resolution 1800 × 600 dpi equivalent (600 × 600 dpi 2bit) Printing Speed Type 1: • Full color : 8 ppm • Monochrome : 24 ppm Type 2: • Full color : 10 ppm • Monochrome : 32 ppm (A4K, 8/" × 11"K plain paper) Note ❒ The printing speed depends on the machine. Check which type of machine you have. See the General Settings Guide.
Specifications Component Specification Operating Systems supported by this machine Windows 95/98/Me Windows 2000 Windows XP Windows NT 4.0 Mac OS 8.6 to 9.2 Mac OS X *1 To use NetBEUI, use the SmartNetMonitor for Client port. Options Limitation ❒ The optional IEEE 1394 Interface Unit and the optional 802.11b Interface Kit (Wireless LAN board) cannot be installed in the machine at the same time. IEEE 1394 Interface Unit Type 4510 ❖ Transmission Spec.
Appendix ❖ Connectable number of devices on a bus: Maximum 63 ❖ Allowed cable hops on a bus: Maximum 16 ❖ Power supply: Non power supply Cable Power repeated (IEEE 1394a-2000 compliant) PostScript 3 Board Type 1232 Reference See the PostScript 3 Board Type 1232 Operating Instructions Supplement for information. IEEE 802.11b Interface Kit Type B ❖ Transmission Spec.: Based on IEEE 802.
Specifications Memory Unit Type C 128MB/256MB ❖ Module Type: SO-DIMM (Small Outline Dual-in-line Memory Module) ❖ Memory Type: SDRAM (Synchronous Dynamic RAM) ❖ Number of Pins: 144 pins 6 61
INDEX A Auto Color Calibration, 41 C Canceling a print job Macintosh, 10 Windows, 9 Configuration page, 52 Control panel locked print, 15 printer features, adjusting, 43 sample print, 15 D Data In indicator, 35, 38, 39 Display panel error messages, 27 Document Server, 25 E Error messages, 27 F Fonts, 58 H Hard disk, 58 Host Interface, 50 I IEEE 1394 Interface Unit Type 4510, 59 IEEE 802.
S Sample Print, 15 Specifications, 58 Spool printing, 56 Staple, 53 System, 47 T Telnet, 31 Troubleshooting, 27 error messages, 27 machine does not print, 34 other printing problems, 36 status messages, 27 U UNIX, 31 W Windows canceling a print job, 9 Windows 2000/Windows XP printer driver, uninstalling, 11 printer properties, printer driver, 4 Windows 95/98/Me printer driver, uninstalling, 11 printer properties, printer driver, 3 Windows NT 4.
64 UE USA B463
Copyright © 2002
Printer/Scanner Kit Type 1232 Operating Instructions Printer Reference 2 UE USA B463-8627A
