Operating Instructions SDC326 Copy Reference Tr sh9 00 e. eps Read this manual carefully before you use this product and keep it handy for future reference. For safety, please follow the instructions in this manual.
Introduction This manual contains detailed instructions on the operation and maintenance of this machine. To get maximum versatility from this machine all operators should carefully read and follow the instructions in this manual. Please keep this manual in a handy place near the machine. Please read the Safety Information before using this machine. It contains important information related to USER SAFETY and PREVENTING EQUIPMENT PROBLEMS.
Note to users in the United States of America Notice: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Notice Do not make copies of any item for which copying is prohibited by law. Copying the following items is normally prohibited by local law: Bank bills, revenue stamps, bonds, stock certificates, bank drafts, checks, passports, driver's licenses. The color copy samples in this book may differ slightly from the actual copies due to printing effects. This machine is equipped with a function that prevents making counterfeit bank bills.
Safety Information When using your equipment, the following safety precautions should always be followed. Safety During Operation In this manual, the following important symbols are used: R WARNING: Indicates a potentially hazardous situation which, if instructions are not followed, could result in death or serious injury. R CAUTION: Indicates a potentially hazardous situation which, if instructions are not followed, may result in minor or moderate injury or damage to property.
R CAUTION: • Protect the equipment from dampness or wet weather, such as rain, snow, and so on. • Unplug the power cord from the wall outlet before you move the equipment. While moving the equipment, you should take care that the power cord will not be damaged under the equipment. • When you disconnect the power plug from the wall outlet, always pull the plug (not the cable). • Do not allow paper clips, staples, or other small metallic objects to fall inside the equipment.
How to Read This Manual Symbols In this manual, the following symbols are used: R WARNING: This symbol indicates a potentially hazardous situation that might result in death or serious injury when you misuse the machine without following the instructions under this symbol. Be sure to read the instructions, all of which are described in the Safety Information section.
TABLE OF CONTENTS What You Can Do with This Machine ...................................................... 2 Guide to Components ............................................................................... 4 Options ....................................................................................................... 6 Operation Panel ......................................................................................... 7 Panel Display .................................................................
Reduce/Enlarge ....................................................................................... Preset R/E................................................................................................... Zoom ........................................................................................................... Directional Magnification (%) ...................................................................... Directional Size Magnification (inch) ...............................................
D Changing The Toner Cartridge........................................................ Pulling Out the Toner Cartridge ................................................................ Setting the New Toner Cartridge............................................................... x Clearing Misfeeds............................................................................. When A, B, C or Y is Displayed: ............................................................... When P is Displayed: ...................
3-bin Sorter (Option) ............................................................................. 166 1000-sheet Tray Unit (Option) .............................................................. 167 1500-sheet Tray Unit (Option) .............................................................. 168 INDEX......................................................................................................
1
What You Can Do with This Machine Trsx012n.
3
Guide to Components Trsh011e.eps 1. Platen cover (option) 5. Stopper Lower this cover over originals placed on the exposure glass for copying. When you copy onto thin paper, raise this to prevent curling. 2. Flip cover 6. Paper tray Flip this up when to access the keys underneath. Set paper here. 3. Main power switch Open to access the inside of the machine. To start the machine, turn on this switch.
Trsh901e.eps 1. Bypass tray Use to copy onto OHP transparencies, adhesive labels, translucent paper, post cards, and custom size paper. 2. Right covers Open this cover to remove jammed paper. 3. Ventilation holes Prevent overheating. Do not obstruct the ventilation holes by placing or leaning an object near them. If the machine overheats, a fault might occur.
Options This machine can be provided with the following options: TRSP012E.eps 1. Platen cover 5. 1500-sheet tray unit (three 500- Lower this cover over originals placed on the exposure glass for copying. Consists of three paper trays. 2. Document feeder (ADF) 6. 20-bin sorter stapler Insert a stack of originals here. They will be fed automatically. Sorts, stacks, and staples copies. 3. Original tray 4. 1000-sheet tray unit (two 500- Sorts and stacks copies.
Operation Panel 1. {User Tools}} key 8. {Selection}} keys Press to change the default settings and conditions to meet your requirements. Press the key under the item you wish to select. 2. {Color Balance}} key 9. Indicators Press to adjust and store the color balance. ⇒ P.97 “Color Balance”. These indicators show errors or the status of the machine. ⇒ P.111 “What to Do If Something Goes Wrong”. 3. {Menu}} key Displays the names of available functions. 4.
16. Main Power indicator 29. {Auto Reduce/Enlarge}} key This indicator goes on when the main power switch is turned on, and goes off when the switch is turned off. Enlarges or reduces the image automatically according to the specified paper size. ⇒ P.51 “Auto Reduce/Enlarge”. 17. On indicator 30. {Zoom}} key This indicator goes on when the operation switch is turned on, and goes off when the switch is turned off. Enlarges or reduces in 1 % steps. ⇒ P.61 “Zoom”. 18.
Panel Display The panel display shows the status of the machine, error messages, and function menus. Important ❒ Do not apply a strong shock or force of about 30N or more to the panel display or you could damage it. Note ❒ Currently selected items are shown highlighted on the panel display (e.g. Auto ). ❒ Keys that are not available are shown grayed out (e.g. OK ). Layout and Keys ❖ Initial display Czss013n.eps 1. The machine status and messages appear here. 2. Items which can be selected or specified.
❖ Function menu display Trss453e.eps 1. A ✓ mark appears before the names of functions that are currently selected. 2. The machine status and messages appear here. 3. Items which can be selected or specified. Common Keys [OK] Confirm the selected function or value and return to the previous display. [Cancel] Cancel the selected function or value and return to the previous display. [↑ ↑Prev.][↓ ↓Next] When there are too many items to fit on the display, use these keys to move between pages.
Sample display for color erase Trss462e.eps 1. The machine status and messages appear here. 2. Available settings. 3. A screened key means you should press it. k Press the [OK] key. Trss454e.eps 1. Selected item. 2. Cancel the settings and return to the previous display. 3. Confirm the settings and return to the previous display.
12
1. Basics Turning On the Power To turn the machine on, press the operation switch. Note ❒ This machine automatically enters Energy Saver mode or turns itself off if you do not use the machine for a while. For details, ⇒ P.52 “Energy Saver Mode”. For details Auto Off Timer, ⇒ P.135 “System settings”. - Power Switches This machine has two power switches. ❖ Operation switch (right side of the operation panel) Press this switch to activate the machine. When the machine has warmed up, you can make copies.
Basics Starting the Machine A Press the operation switch to make the On indicator go on. 1 Trss040n.eps Note ❒ If the power is not turned on when the operation switch is pressed, check if the main power switch is on. If off, turn it on. ❒ During the warm-up period (Less than 270 seconds), you can use the Auto Start function. ⇒ P.54 “Auto Start”. When the machine is set for user codes A Enter your user code using the number keys. Then press the {#}} key.
Turning On the Power Shutting down the machine A Press the operation switch to make the On indicator go off. 1 Turning off the main power A Turn off the main power switch. The main power indicator of the operation panel goes off.
Basics Originals Standard Size Originals 1 The machine will detect originals of the following sizes and directions as standard size originals: ❖ When you set originals on the exposure glass Metric version A3L, B4L, A4LK, B5LK, 81/2" × 13"L Inch version 11" × 17"L, 10" × 14"L, 81/2" × 14"L, 81/2" × 13"L, 81/2" × 11"LK ❖ When you set originals in the document feeder Metric version A3L, B4L, A4LK, B5LK, A5LK, B6LK, 267 × 390mmL, 195 × 267mmLK, 11" × 17"L, 81/2" × 13"L, 81/2" × 11"LK Inch version A4L
Originals • • • • • • • • Pasted originals Damp originals Sticky originals Wavy originals Originals that are not made from paper Originals written in pencil on both sides, or two-sided carbon originals Thermal fax paper, CRO (camera ready originals) or aluminum foil Books, pamphlets, and booklets 1 17
Basics Setting Originals on the Exposure Glass A Lift the platen cover or the document feeder. B Set the original face down on the exposure glass. The original must be 1 aligned with the rear left corner. Trsr010e.eps 1. Reference mark 2. Scale Note ❒ Start with the first page to be copied. C Lower the platen cover or the document feeder.
Setting a Stack of Originals in the Document Feeder Setting a Stack of Originals in the Document Feeder 1 You can insert a stack of originals into the document feeder. These originals are individually fed onto and removed from the exposure glass. Note ❒ Some originals are unsuitable for the document feeder. ⇒ P.16 “Non-recommended Originals for the Document Feeder”. ❒ Do not press down or hold originals after inserting them.
Basics D Set the originals face up into the document feeder until the Insert Original indicator goes off. Trsr020e.eps 1 1. Limit mark 2. Original guide Note ❒ The last page should be on the bottom. ❒ The original guide must touch the front side of the originals. ❒ Do not stack originals above the limit mark.
Setting one Original at a Time in the Document Feeder Setting one Original at a Time in the Document Feeder 1 If you set one original at a time in the document feeder, the second and subsequent originals can be fed and copied automatically without pressing the {Start} key. Note ❒ Do not press down or hold originals after inserting them. ❒ While originals are fed from the original table to the exposure glass, do not pull them out.
Basics F While the Auto Feed indicator is lit after an original is fed, set the next original. The original is automatically fed and copied. Trsr030e.eps 1 Note ❒ You can adjust the time the machine waits before being ready for the next original with the user tools.
Setting Originals of Different Sizes in the Document Feeder Setting Originals of Different Sizes in the Document Feeder 1 Preparation To use this function, you have to select ADF Mixed Sizes mode with the user tools. ⇒ P.146 “ADF/Sorter”. You can insert a stack of originals of different standard sizes (e.g. A4, B5 etc.) into the document feeder. These originals are individually fed onto and removed from the exposure glass.
Basics Setting Custom Sized Originals When copying from custom sized originals, enter the original size so that copy is well aligned. 1 Limitation ❒ You must set your custom sized originals on the exposure glass. Reference For the standard sizes the machine can detect, ⇒ P.16 “Standard Size Originals”. Note ❒ The dimensions you can enter must be within the following ranges: Vertical size 50 - 297mm (in 1mm steps), 2.0" - 11.7" (in 0.1" steps) Horizontal size 50 - 432mm (in 1mm steps), 2.
Setting Custom Sized Originals D Enter the vertical original size with the number keys, then press the > or {#} } key. Copy301.tif 1 Note ❒ To change the value entered, press the {Clear/Stop} key and enter the new value. E Enter the horizontal original size with the number keys, then press the [OK] key. Copy302.tif Trss114e.eps F Set your original on the exposure glass, then press the {Start}} key.
Basics Removing the Platen Cover to Copy a Large Original 1 You can remove the platen cover to copy a large (more than A3, 11" × 17") original. Note ❒ You cannot remove the document feeder. To remove the platen cover, lift it out. Trsh090e.eps Note ❒ Lift the platen cover with both hands. Place the removed cover on a flat surface, such as a desk, and where it will not be damaged. To reset the platen cover, align the pins of the platen cover and the holes of the copier.
2. Copying Basic Procedure A Set your original on the exposure glass or in the document feeder. B Make sure that the [Auto Text/Photo], [Auto Color Select], [Auto] (Auto Paper Select), and [100%] are selected. Copy303.tif Note ❒ Auto Text / Photo ⇒ P.35 “Auto Text/Photo mode”. ❒ Auto Color Select ⇒ P.30 “Auto color selection mode”. ❒ Auto Paper Select ⇒ P.40 “Auto paper select”. C Enter the number of copies required using the number keys. Czss012n.
Copying D Press the {Start}} key. Czss010n.eps 2 Note ❒ To stop the machine during a multi-copy run, press the {Clear/Stop} key. ❒ If you want to change the settings, press the {Clear/Stop} key. If you want to resume the copy run, press the {Start} key. ❒ To return the machine to the initial condition after copying, press the {Clear Modes} key. Adjusting Copy Image Density Image density affects the contrast of copies. With these functions you can control the image density so that copies match originals.
Basic Procedure Manual image density If you require darker or lighter copies, adjust the image density yourself. A If the Auto Image Density indicator is lit, press the {Auto Image Density}} key to cancel it. B Press the {Lighter}} (left) key to lower the image density. Press the {Darker}} 2 (right) key to increase the image density. Trss180n.eps Combined auto and manual image density Use when copying originals with a dirty background (such as newspapers).
Copying Selecting a Color Mode Select a color mode that best suits your originals and copying requirements. Auto color selection mode The machine automatically detects whether the original has color parts or not. Originals containing only black images will be copied in Black mode. Originals with some color areas will be copied in Full Color mode. 2 Note ❒ If you make one copy set of a black original using the document feeder, it is recommended to select Black mode.
Basic Procedure A Press the 12 keys to light the Full Color indicator. Czss004n.eps 2 B Set your originals, then press the {Start}} key. Black copy mode This function makes copies in black. A Press the 12 keys to light the Black indicator. Czss005n.eps B Set your originals, then press the {Start}} key. Single color mode This function makes copies in single colors.
Copying A Press the 12 keys to light the Single Color indicator. Czss006n.eps 2 B Select the color with the <> keys. Then press the [OK] key. Copy207.tif Trss115e.eps Note ❒ You can select the color density level after pressing the [Density] key. C Set your originals, then press the {Start}} key. Twin color mode Two methods are available: ❖ Twin Color (Color Copy) Reproduces black areas of the original in one selected color and areas in other colors using the second selected color.
Basic Procedure Twin Color (Color copy) A Press the 12 keys to light the Twin Color indicator. Czss007n.eps 2 B Press the [Colors] key. Copy209.tif Trss111e.eps C Select the color you want to copy in for the color parts of the original with the <> keys. Then press the [OK] key. Copy010.tif Trss115e.eps D Press the [Black] key. Copy209.tif Trss112e.
Copying E Select the color you want to copy in for the black parts of the original with the <> keys. Then press the [OK] key. Copy011.tif Trss115e.eps 2 F Set your originals, then press the {Start}} key. Twin Color (Red & Black) Note ❒ If Color Sensitivity is set to wide, the machine recognizes orange or purple as red. This adjustment affect Color Erase or Color Conversion. ⇒ P.100 “Image Adjustment”. A Press the 12 keys to light the Twin Color indicator. Czss007n.eps B Press the [Red&BK] key.
Basic Procedure C Press the [OK] key. Copy210.tif Trss115e.eps 2 D Set your originals, then press the {Start}} key. Selecting the Original Image Type (Photo/Text) To optimize the likeness between copies and originals, select an image type that matches your originals. Note ❒ You can adjust the readability of black lettering in colored areas, ⇒ P.100 “Image Adjustment”. Auto Text/Photo mode This mode automatically detects the areas of your original containing text or photographs.
Copying B Press the {Original}} key. Czss001n.eps 2 C Press the [Photo Typ] key. Copy012.tif Trss111e.eps D Select the photo type with the <> keys. Then press the [OK] key. Copy013.tif Trss115e.eps E Press the [OK] key. F Set your originals, then press the {Start}} key. Text mode This mode is suitable for copying originals consisting of characters, line diagrams, and letter, but not photograph images.
Basic Procedure A Press the {Original}} key. Czss001n.eps 2 B Select [Text] with the <> keys. Then press the [OK] key. Copy012.tif Trss115e.eps C Set your originals, then press the {Start}} key. Photo mode This mode is suitable for copying originals consisting of pictures, photographs, and screened letters/areas, but not solid letters. Note ❒ There are 3 types of Photo mode: • [Press Print]: Use when copying photographs or pictures that are printed on paper (e.g. magazines).
Copying A Press the {Original}} key. Czss001n.eps 2 B Select [Photo] with the <> keys. Copy012.tif Trss116e.eps C Press the [Photo Typ] key. Copy014.tif Trss111e.eps D Select the photo type with the <> keys. Then press the [OK] key. Copy013.tif Trss115e.eps E Press the [OK] key. F Set your originals, then press the {Start}} key.
Basic Procedure Special original mode Use this function for originals written in highlight pen, originals printed from inkjet printers, or maps. A Press the {Original}} key. Czss001n.eps 2 B Select [Special Orig.] with the <> keys. Then press the [OK] key. Copy012.tif Trss115e.eps C Select the original type with the <> keys. Then press the [OK] key. Copy015.tif Trss115e.eps D Set your originals, then press the {Start}} key.
Copying Selecting the Copy Paper Size Select a suitable size of copy paper based on the original size and the reproduction ratio. Auto paper select 2 The machine automatically selects a suitable size of copy paper based on the original size and the reproduction ratio. Reference Regarding functions that cannot be used together with this function, ⇒ P.105 “Combination Chart”. Note ❒ Sizes of certain originals might not be detected depending on the original size and type.
Basic Procedure - Image Rotation If the direction in which your original is set (landscape or portrait) is different from that of the paper you are copying onto, this function rotates the original image by 90° and fits it on the copy paper. This function works when Auto Paper Select or Auto Reduce/Enlarge is selected. ⇒ P.140 “General features” 2 Note ❒ The following functions cannot be used.
Copying Copying from the Bypass Tray Use the bypass tray to copy onto thick paper, adhesive labels, OHP transparencies, or custom size paper. Also use the bypass tray to copy onto the reverse side of paper that has already been copied onto.
Basic Procedure ❒ Select one of the following settings or keys: • [Normal]: normal paper • [Thick]: thick paper, post cards, adhesive labels, translucent paper • [OHP]: OHP transparencies • [Duplex]: Use for copying onto the reverse side of paper that has been already copied onto. ⇒ P.49 “Copying onto the reverse side of paper”. • [Duplex Thick]: Use for copying onto the reverse side of thick paper (105160g/m2, 28-43 lb) that has been copied onto. ⇒ P.49 “Copying onto the reverse side of paper”.
Copying A Open the bypass tray. Trsh040e.eps 2 B Select [Normal], [Thick] or [OHP] with the <> keys. Copy305.tif Trss116e.eps L/K K] key to select the paper direction. C Press the [L Copy305.tif Trss112e.eps D If you selected [OHP] in step 2, press the [OK] key then select whether blank slip sheets are inserted between OHP transparencies with the <> keys. Copy018.tif Trss116e.
Basic Procedure E Press the [OK] key. F Adjust the paper guides to the paper size. Trsh050e.eps 2 1. Horizontal size 2. Vertical size 3. Extender 4. Paper guides Note ❒ Make sure the paper size and direction in the bypass tray is displayed on the operation panel. ❒ Make sure that the paper guides match the paper size. If the paper guides are not adjusted to the paper size properly, paper might be skewed or paper misfeed might occur.
Copying C Press the [Custom] key. Copy305.tif Trss111e.eps 2 D Select [Custom1], [Custom2], [Custom3] or [Input Size] with the <> keys. Then press the [OK] key. Copy306.tif Trss115e.eps Note ❒ If you selected [Custom1], [Custom2] or [Custom3], go to step H. E If you selected [Input Size] in step D, enter the vertical paper size with the number keys, then press the > or [#] key. Copy307.tif Note ❒ To change the value entered, press the {Clear/Stop} key and enter the new value.
Basic Procedure H Adjust the paper guides to the paper size. Trsh050e.eps 2 1. Horizontal size 2. Vertical size 3. Extender 4. Paper guides Note ❒ Make sure that the paper guides match the paper size. If the paper guides are not adjusted to the paper size properly, paper might be skewed or paper misfeed might occur. I With the side you wish to copy onto face up, insert the paper into the bypass tray. J Set your originals, then press the {Start}} key.
Copying Making A3, 11" × 17" full bleed copies By sliding the paper guides of the bypass tray to greater than A3 (11") size, A3, 11" × 17" full bleed copying mode is automatically selected. In this mode, you can make A3, 11" × 17" full bleed copies with 12" × 18" paper. This is useful for making A3, 11" × 17" size copies with a colored background (e.g. catalogues). 2 1. A3, 11" × 17" size Original 2. In standard copy mode, margins appear on copies 3. 12" × 18" Full Bleed Copy 4.
Basic Procedure By sliding the paper guides of the bypass tray, the machine enters A3, 11" × 17" full bleed copying mode automatically. A Pull up the tab. Zcby010e.eps 2 B Leaving the tab up, slide the paper guides until they stop. Zcby020e.eps Note ❒ Make sure that the paper guides match the paper size. ❒ Be sure to return the tab to its original position before you close the bypass tray. If you do not return it correctly, the bypass tray might not close properly.
Copying Original set on the exposure glass Copy paper set on the bypass tray Copies 2 ❒ You cannot use this function for OHP transparencies, translucent paper, adhesive labels and postcards. ❒ Do not use copy paper that has been already copied onto by other machines. ❒ If the copy paper is bent, correct it before setting paper in the bypass tray. If the bend is not corrected, a paper misfeed might occur. A Open the bypass tray.
Basic Procedure B Select [Duplex], or [Duplex Thick] with the <> keys. Copy305.tif Trss116e.eps 2 Note ❒ To copy onto custom size paper, press the [Custom] key and select or enter the size. For details, ⇒ P.45 “Copying onto custom size paper with the bypass tray”. C Press the [OK] key. D Adjust the paper guides to the paper size. Note ❒ Make sure that the paper guides match the paper size.
Copying Example: • Metric version: original: A3L, copy paper: A4L • Inch version: original: 11" × 17"L, copy paper: 81/2" × 11"L A Press the [Auto Reduce/Enlarge] key. Trss342n.eps 2 B Set your originals. L, 81/2" × 11"L L). C Choose your copy paper size (e.g. A4L D Press the {Start}} key. The original image is enlarged or reduced to fit the selected copy paper.
Basic Procedure Auto Off Mode This machine automatically turns itself off 60 minutes after the last copy or print job has finished. If you wish to make copies when the machine is in Auto Off mode, press the operation switch. Reference For how to change the default interval that the machine waits before entering Auto Off mode, see “Auto Timer” ⇒ P.135 “System settings”. 2 Interrupt Copying Use the {Interrupt} key to interrupt a multicopy run and make urgently needed copies.
Copying Auto Start If you press the {Start} key during the warm-up period, the {Start} key will blink and the machine will start copying after the warm-up period. A Set your copy settings during the warm-up period. B Press the {Start}} key. 2 Czss010n.eps Note ❒ To cancel Auto Start, press the {Clear/Stop} key. Program You can store up to five frequently used copy job settings in machine memory and recall them for future use. Storing your settings A Set the copy settings you want to put into memory.
Basic Procedure C Press the [Store] key. Copy021.tif Trss111e.eps 2 D Select the program number you want to store the settings in with the <> keys. Then press the [OK] key. Copy022.tif Trss115e.eps Note ❒ If this program number is already used, the machine asks whether you wish to overwrite it or not. Press the [Yes] or [No] key. Recalling your settings A Press the {Program}} key. Czss011n.eps B Select the program number you want to recall with the <> keys. Copy021.tif Trss116e.
Copying C Press the [OK] key. The stored settings are displayed. D Set your originals, then press the {Start}} key. Deleting a program 2 A Press the {Program}} key. Czss011n.eps B Press the [Delete] key. Copy021.tif Trss112e.eps C Select the program number that contains the program you wish to delete with the <> keys. Then press the [OK] key. Copy023.tif Trss115e.
Basic Procedure D Press the [Yes] key. Copy024.tif Trss114e.eps 2 E Press the [Exit] key. Check Modes By pressing the {Check Modes} key, you can see at a glance the modes you have selected. Czss002n.
Copying Counter By pressing the {Counter} key, you can check the machine's counter. Trss320n.
Reduce/Enlarge Reduce/Enlarge Preset R/E Gcthen1e.eps 2 Reference Regarding functions that cannot be used together with this function, ⇒ P.105 “Combination Chart”. Note ❒ You can add up to two preset ratios with the user tools. ⇒ P.140 “General features”. ❒ You can select a ratio regardless of the size of an original or copy paper. With some ratios, parts of the image might not be copied or margins will appear on copies. ❒ To return to 100%, press the [100%] key. Reducing A Press the [Ratio] key.
Copying B Press the [Reduce] or < key to select the reducing ratio. Copy308.tif Trss118e.eps 2 C Press the [OK] key. D Set your originals, then press the {Start}} key. Enlarging A Press the [Ratio] key. Copy303.tif Trss112e.eps B Press the [Enlarge] or > key to select the enlarging ratio. Copy308.tif Trss119e.eps C Press the [OK] key. D Set your originals, then press the {Start}} key.
Reduce/Enlarge Zoom Gczoom1e.eps 2 You can change the reproduction ratio from 25% to 400% in 1% steps. Note ❒ You can select a ratio regardless of the size of an original or copy paper. With some ratios, parts of the image might not be copied or blank margins will appear on copies. ❒ To return to 100%, press the [100%] key. ❒ You can select a preset ratio which is near the desired ratio, then press the {Zoom} key and adjust the ratio with the [+] or [-] key. ❒ There are two ways to set the ratios.
Copying B Adjust the reproduction ratio with the [+] or [-] key. Copy026.tif Trss117e.eps 2 C Press the [OK] key. D Set your originals, then press the {Start}} key. Using the number keys A Press the {Zoom}} key. Trss202n.eps B Enter the reproduction ratio with the number keys. Copy026.tif C Press the [OK] key. D Set your originals, then press the {Start}} key.
Reduce/Enlarge Directional Magnification (%) Gcdhen1e.eps 2 1. Horizontal % 2. Vertical % Copies can be reduced or enlarged at different reproduction ratios horizontally and vertically. Note ❒ You can select the ratio from 25% to 400%. ❒ You can select a ratio regardless of the size of an original or copy paper. With some ratio, parts of the image will not be copied or blank margins will appear on copies. A Press the {Directional Mag.(%)}} key. Trss212n.
Copying B Enter the vertical ratio with the number keys, or the [+][-] keys. Copy027.tif Trss117e.eps 2 Note ❒ To change the ratio entered, press the {Clear/Stop} key and enter the new ratio. C Press the > or [#] key. D Enter the horizontal ratio with the number keys or the [+][-] keys. Copy028.tif Trss117e.eps E Press the [OK] key. F Set your originals, then press the {Start}} key.
Reduce/Enlarge Directional Size Magnification (inch) Gcdhen2e.eps 2 1. Horizontal original size 2. Vertical original size 3. Horizontal copy size 4. Vertical copy size The suitable reproduction ratios will be automatically selected when you enter the horizontal and vertical lengths of the original and copy image you want. Note ❒ You can enter sizes within the following ranges: Metric Version 1 - 999mm (in 1mm steps) Inch Version 0.1" - 99.9" (in 0.
Copying Note ❒ If you have assigned the Directional Size Magnification (inch) function to one of the {Favorite} keys, press it and go to step D. To assign a function to the {Favorite} keys, ⇒ P.147 “Set favorite keys”. B Press the [↓↓Next] key until [D. Size Mag. (inch)] is displayed. Copy004.tif 2 Trss112e.eps C Select [D. Size Mag. (inch)] with the <> keys, then press the [Select] key. Copy309.tif Trss114e.eps D Enter the vertical original size with the number keys, then press the > or [#] key.
Reduce/Enlarge F Enter the horizontal original size with the number keys, then press the > or [#] key. G Enter the horizontal copy paper size with the number keys, then press the [#] key. H Press the [OK] key. I Set your originals, then press the {Start}} key.
Copying Shifting the Image Centering Gcidoh1e.eps 2 You can move the image to the center. This function is convenient when the copy paper is larger than the original. A Press the {Menu}} key. Trss222n.eps Note ❒ If you have assigned the Centering function to one of the {Favorite} keys, press it and go to step D. To assign a function to the {Favorite} keys, ⇒ P.147 “Set favorite keys”. B Select [Centering] with the <> keys. Then press the [Select] key. Copy004.tif Trss115e.
Shifting the Image C Press the [Exit] key. D Select the copy paper size. E Set your originals, then press the {Start}} key. Margin Adjustment 2 Gctojs1e.eps You can make a margin by shifting the image to the left or right. This function is convenient when you want to bind copies. Note ❒ You can change the width of the binding margin as follows. Metric Version 0 - 20mm (in 1mm steps) Inch Version 0" - 0.8" (in 0.1" steps) ❒ The margin width default is as follows.
Copying A Press the {Menu}} key. Trss222n.eps 2 Note ❒ If you have assigned the Margin Adjustment function to one of the {Favorite} keys, press it and go to step C. To assign a function to the {Favorite} keys, ⇒ P.147 “Set favorite keys”. B Select [Margin Adjustment] with the <> keys. Then press the [Select] key. Copy004.tif Trss115e.eps C Select [Left] (left margin) or [Right] (right margin) with the <> keys. Then enter the desired margin width with the number keys. Copy312.tif Trss116e.
Series Copies Series Copies Book → 1 Sided Gcsepr1e.eps 2 This function makes one-sided copies from two facing pages of bound (book) originals. Reference Regarding functions that cannot be used together with this function, ⇒ P.105 “Combination Chart”. A Press the {Menu}} key. Trss222n.eps Note ❒ If you have assigned the Series Copies function to one of the {Favorite} keys, press it and go to step D. To assign a function to the {Favorite} keys, ⇒ P.147 “Set favorite keys”.
Copying B Press the [↓↓Next] key until [Series] is displayed. Copy004.tif Trss112e.eps 2 C Make sure that [Series] is selected, then press the [Select] key. Copy309.tif Trss114e.eps Note ❒ If your machine do not have the document feeder, go to step E. D Make sure that [Book → 1 Sided] is selected, then press the [OK] key. Copy034.tif Trss114e.eps E Select the copy paper size. F Set your originals, then press the {Start}} key.
Series Copies 2 Sided → 1 Sided The optional document feeder is required to use this function. Gcsepr2e.eps 2 Reference Regarding functions that cannot be used together with this function, ⇒ P.105 “Combination Chart”. A Press the {Menu}} key. Trss222n.eps Note ❒ If you have assigned the Series Copies function to one of the {Favorite} keys, press it and go to step D. To assign a function to the {Favorite} keys, ⇒ P.147 “Set favorite keys”. B Press the [↓↓Next] key until [Series] is displayed. Copy004.
Copying C Make sure that [Series] is selected, then press the [Select] key. Copy309.tif Trss114e.eps 2 →1 Sided] with the <> keys, then press the [OK] key. D Select [2 Sided→ Copy034.tif Trss115e.eps E Select the copy paper size. F Set your originals in the document feeder, then press the {Start}} key. Combine 2 Originals The optional document feeder is required to use this function. Gcsyyk1e.eps This function automatically combines 2 one-sided originals onto one copy.
Series Copies Reference Regarding functions that cannot be used together with this function, ⇒ P.105 “Combination Chart”. A Press the {Menu}} key. Trss222n.eps 2 Note ❒ If you have assigned the Combine 2 Originals function to one of the {Favorite} keys, press it and go to step C. To assign a function to the {Favorite} keys, ⇒ P.147 “Set favorite keys”. B Select [Combine 2 Orig.] with the <> keys, then press the [Select] key. Copy004.tif Trss115e.eps C Select the copy paper size.
Copying Cover Sheet Front Cover The optional document feeder is required to use this function. 2 Gchyos1e.eps Note ❒ The cover sheets should be identical in size and direction with the copy paper. ❒ The cover sheets should be fed from the bypass tray. ❒ The covers are copied in Thick Paper mode. Reference Regarding functions that cannot be used together with this function, ⇒ P.105 “Combination Chart”. A Press the {Menu}} key. Trss222n.
Cover Sheet B Press the [↓↓Next] key until [Cover Sheet] is displayed. Copy004.tif Trss112e.eps 2 C Select [Cover Sheet] with the <> keys, then press the [Select] key. Copy233.tif Trss115e.eps D Make sure that [Front Cover] is selected, then press the [OK] key. Copy036.tif Trss114e.eps E Select orientation of the copy paper and cover sheets with the <> keys, then press the [OK] key. Copy038.tif Trss115e.eps F Set cover sheets into the bypass tray. G Set your originals in the document feeder.
Copying Front & Back Covers The optional document feeder is required to use this function. ❖ Back Cover: Copy Gchyos3e.eps 2 ❖ Back Cover: Blank Gchyos2e.eps Note ❒ You can specify whether to make a copy on a back cover sheet. If you select [Copy], the last page will be copied on the back cover sheet. If you select [Blank], a cover sheet will just be inserted after the last copy. ❒ The cover sheets should be identical in size and direction with the copy paper.
Cover Sheet A Press the {Menu}} key. Trss222n.eps 2 Note ❒ If you have assigned the Cover Sheet function to one of the {Favorite} keys, press it and go to step D. To assign a function to the {Favorite} keys, ⇒ P.147 “Set favorite keys”. B Press the [↓↓Next] key until [Cover Sheet] is displayed. Copy004.tif Trss112e.eps C Select [Cover Sheet] with the <> keys, then press the [Select] key. Copy233.tif Trss115e.eps D Select [Front & Back Cover] with the <> keys, then press the [OK] key. Copy036.
Copying E Specify whether to copy on back cover sheets with the <> keys, then press the [OK] key. Copy039.tif Trss115e.eps 2 F Select orientation of the copy paper and cover sheets with the <> keys, then press the [OK] key. Copy038.tif Trss115e.eps G Set cover sheets into the bypass tray. H Set your originals in the document feeder. I Press the {Start}} key.
Color Creation Color Creation Color Conversion This function converts a selected color of an original into a different color on the copy. 2 Note ❒ Up to 4 colors can be converted at one time. ❒ Colors that can be converted: Red, Green, Blue, Yellow, Cyan, Magenta, Black, and White ❒ Colors you can convert to: Red, Green, Blue, Yellow, Cyan, Magenta, Yellow Green, Orange, Marine Blue, Beige, Pink, Purple, and Black ❒ This function can be made more or less sensitive to the color to be converted.
Copying B Press the [↓↓Next] key until [Color Conversion] is displayed. Copy004.tif Trss112e.eps 2 C Select [Color Conversion] with the <> keys, then press the [Select] key. Copy309.tif Trss115e.eps D Select the original color (color to be converted) with the <> keys, then press the [OK] key. Copy043.tif Trss115e.eps E Select the new color (color to convert to) with the <> keys. Copy044.tif Trss116e.eps F If you want to select the color density level, press the [Density] key.
Color Creation G Select the level with the <> keys. Then press the [OK] key. Copy045.tif Trss115e.eps 2 H Press the [OK] key. I If you want to convert more than one color, press the [Add] key. Then repeat steps D to H. Copy046.tif Trss112e.eps Note ❒ Repeat step I until you have finished designating colors. ❒ If you pick the wrong color, press the [Delete] key. J Press the [OK] key. K Set your originals, then press the {Start}} key.
Copying A Press the {Menu}} key. Trss222n.eps 2 Note ❒ If you have assigned the Color Erase function to one of the {Favorite} keys, press it and go to step D. To assign a function to the {Favorite} keys, ⇒ P.147 “Set favorite keys”. B Press the [↓↓Next] key until [Color Erase] is displayed. Copy004.tif Trss112e.eps C Select [Color Erase] with the <> keys, then press the [Select] key. Copy309.tif Trss115e.eps D Select the color to be erased with the <> keys, then press the [OK] key. Copy002.
Color Creation E If you want to erase more than one color, press the [Add] key. Then repeat step D. Copy003.tif Trss112e.eps 2 Note ❒ Repeat step E until you have finished designating colors. ❒ If you pick the wrong color, press the [Delete] key. F Press the [OK] key. G Set your originals, then press the {Start}} key.
Copying Image Creation Mirror Gcmill1e.eps 2 This function makes a mirror image copy of the original. Note ❒ Set the original as below when setting on the exposure glass. Gcmill2e.eps A Press the {Menu}} key. Trss222n.eps 86 Note ❒ If you have assigned the Mirror function to one of the {Favorite} keys, press it and go to step D. To assign a function to the {Favorite} keys, ⇒ P.147 “Set favorite keys”.
Image Creation B Press the [↓↓Next] key until [Mirror] is displayed. Copy004.tif Trss112e.eps 2 C Make sure that [Mirror] is selected, then press the [Select] key. Copy233.tif Trss115e.eps D Set your originals, then press the {Start}} key. Positive/Negative Gchatn1e.eps This function copies the original image in complementary colors. If you use a black and white original, black and white areas of the original are reversed.
Copying A Press the {Menu}} key. Trss222n.eps 2 Note ❒ If you have assigned the Positive/Negative function to one of the {Favorite} keys, press it and go to step D. To assign a function to the {Favorite} keys, ⇒ P.147 “Set favorite keys”. B Press the [↓↓Next] key until [Positive/Negative] is displayed. Copy004.tif Trss112e.eps C Select [Positive/Negative] with the <> keys. Then press the [Select] key. Copy233.tif Trss115e.eps D Set your originals, then press the {Start}} key.
Finishing Finishing Note ❒ To avoid problems caused by curled copies, try turning over the paper stack in the paper tray. If there is no improvement, change to copy paper with less curl. 2 Reference Regarding functions that cannot be used together with this function, ⇒ P.105 “Combination Chart”. Sort The optional 20-bin sorter stapler, 10-bin sorter stapler, or 3-bin sorter is required to use this function. Gcsort1e.
Copying Note ❒ It is recommended to set originals in the document feeder with this function.
Finishing Stack The optional 20-bin sorter stapler, 10-bin sorter stapler, or 3-bin sorter is required to use this function. Gcsort2e.eps 2 All copies of each original are delivered to the same bin.
Copying A Press the {Sorter}} key until the Stack indicator (bottom) is lit. Trss302n.eps 2 B Set your originals in the document feeder. C Press the {Start}} key. Staple The optional 20-bin sorter stapler, 10-bin sorter stapler is required to use this function. Gcsort3e.eps Each copy set can be stapled together. Note ❒ Since the image is rotated, if the direction of the original and paper direction differ, the staples might not be in the desired position.
Finishing ❒ Stapling position and original setting: Original setting Exposure glass Stapling position Document Feeder 20-bin sorter stapler 10-bin sorter stapler K 2 L ❒ For stapling, the following limitations apply: 20-bin sorter stapler Normal paper mode 10-bin sorter stapler Thick paper mode Maximum paper size L A3, 11" × 17" K A4, 81/2" × 11" L A3, 11" × 17" K A4, 81/2" × 11" L A3, 11" × 17" K A4, 81/2" × 11" Minimum paper size L B5, 81/2" × 11" K B5, 81/2" × 11" L B5, 81/2" × 11" K B5, 81
Copying Changing the staple position If your machine is equipped with the 20-bin sorter stapler, you can select one of two stapling positions by changing the position of the stapler. Open the front cover of the sorter stapler and perform the actions illustrated below. Trsp050e.eps 2 Trsp060e.eps Note ❒ After changing the position of the stapler, the stapler should be clicked in position. Stapling copies automatically after copying The optional document feeder is required to use this function.
Finishing A Press the {Sorter}} key until the Sort (top) and Staple (center) indicators are lit. Trss302n.eps 2 B Set your originals in the document feeder. C Press the {Start}} key. Stapling copies manually after copying A Press the {Sorter}} key until the Sort indicator (top) is lit. Trss302n.eps B Make your copies. C After copying is completed, press the {Sorter}} key before the Staple indicator stops blinking.
Copying 2 96
