Use And Care Manual

21
Installation Instructions
a. Hand Assembly:
1. Make certain the tank valve and all the appliance valves are in the “OFF” position.
2. When connecting the regulator/burner valve assembly to the tank valve,
turn the large plastic nut clockwise until it stops.
3.Gas will not flow unless the plastic nut is completely connected.
4. HAND TIGHTEN ONLY.
b. Hand Disassembly:
1.Make certain the tank valve and all the appliance valves are in the “OFF” position.
2.Turn the large plastic nut counter-clockwise until it is disassembled.
3. HAND LOOSEN ONLY.
c. Excess Flow Control
To ensure this does not cause difficulty in lighting the grill,follow these
instructions:
1. Make sure all burner valves are “OFF”.
2. Open the tank valve and wait 5 seconds.
d.Temperature-Activated Shut-Off
The large plastic nut on the regulator assembly is designed in coordination
with a check valve in the tank valve to shut off the flow of gas when exposed
to temperatures between 240-300° F In the event of a fire or hose break,
one of the safeguards will function to control or stop the flow of gas from the
propane tank.Never attempt to use damaged equipment.
IMPORTANT:Before the use of a fresh tank of gas,please check leakage
around the connections according to section “Checking Gas Leaks” on
page and make sure there is no leakage or vapor accumulation in the 28
cabinet.Make sure all openings around side walls are not blocked.
IMPORTANT:Place dust cap on cylinder valve outlet whenever the cylinder
is not in use.Only install the type of dust cap on the cylinder valve outlet
that is provided with the cylinder valve.Other types of caps or plugs may
result in leakage of propane.
1。确保水箱阀门和所有电器阀门都处于“关闭”状态。
重要提示:在使用新油箱前，请按照第28页“检查气体泄漏”一节检查连接部位的泄漏情况，并确保柜内没有泄漏或蒸汽积聚。
确保侧壁周围的所有开口都没有堵塞。
b。手动拆卸:
丙烷调节阀总成包含一个设计用于在正常情况下为烤架提供足够的气体流量，同时控制过量气体流量的过量流动装置。
压力的迅速变化可以触发提供低火焰和低温的过量流动装置。如果当燃烧器阀门打开时，油箱阀门打开以允许气体流动，
压力的激增将导致装置启动。设备将保持关闭状态，直到压力平衡。这应该在5秒内发生。
为了确保这不会造成烤架照明困难，请遵循以下说明:
1。确保所有燃烧器阀门“关闭”。
2。打开水箱阀门，等待5秒。
调节器上的大型塑料螺母装配设计配合在罐阀止回阀关闭时的气体流动接触温度在240 - 300°F在发生火灾或软管破裂,
一个保障的函数来控制或阻止气体的流动丙烷罐。不要试图使用损坏的设备。
2。将大塑料螺母逆时针旋转直到拆卸。
1。确保水箱阀门和所有电器阀门都处于“关闭”状态。
2。当将调节阀/燃烧器总成连接到油箱阀门上时，顺时针旋转大塑料螺母，直到它停止。
3.除非塑料螺母完全连接，否则气体不会流动。
3.只手松开。
d。Temperature-Activated关闭
收到手动连接
c.过量流量控制
4所示。只手收紧。
重要提示:当气缸不使用时，在气缸阀出口放置防尘帽。只在装有气缸阀的气缸阀出口处安装防尘帽的型号。
其他类型的盖子或插头可能导致丙烷泄漏。
The propane regulator assembly incorporates an excess flow device designed
to supply the grill with sufficient gas flow under normal conditions yet control
excess gas flow.
Rapid changes in pressure can trigger the excess flow device providing a low
flame and low temperature.If the tank valve is turned open to allow gas flow
while a burner valve is open,the surge of pressure will cause the device to
activate.The device will remain closed until the pressure is equalized.This
should occur within 5 seconds.