CEILING FAN OWNER'S MANUAL READ AND SAVE THESE INSTRUCTIONS MODELS: 52-ECM-5RV-13 52-ECM-5RV-WH 52-ECM-5RV-SN FAN RATING AC 120V.
1. TOOLS AND MATERIALS REQUIRED Philips screwdriver Blade screwdriver 11 mm wrench Step ladder Wire cutter 2. PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items; a. b. c. d. e. f. g. h. i. J. k. l.
. SAFETY RULES 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National Electrical Code and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 8. Avoid placing objects in the path of the blades. 9. To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning the fan. 10.
. MOUNTING OPTIONS If there isn't an existing CUL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Outlet box Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support must be able to fully support the moving weight of the fan (at least 50 lbs). Do not use plastic outlet boxes.
. HANGING THE FAN REMEMBER to turn off the power. Follow the steps below to hang your fan properly. CUL Listed electrical box NOTE: This ceiling fan is supplied with two types of hanging assemblies; the standard ceiling installation using the downrod with ball and socket mounting and the "close-to-ceiling" installation. The "close-to -ceiling" installation is recommended in rooms with less than 8-feet ceilings or in areas where additional space is desired from the floor to the fan blades.
CLOSE-TO-CEILING INSTALLATION 1. Pass the 120-volt supply wires through the center hole in the ceiling hanger bracket as shown in Fig. 5. Canopy Figure 8 2. Remove the decorative canopy cover from the canopy. (Fig. 8) 3. Secure the hanger bracket to the ceiling outlet box with the screws and washers provided with your outlet box. Decorative canopy cover Screw and lockwasher (3 of 6 places) Canopy 4. Remove three of the six screws and lock washers (every other one) from the collar of top motor. (Fig.
6. INSTALLATION OF SAFETY SUPPORT An additional safety support is provided to prevent the fan from falling. Secure the safety cable to the ceiling joist with screw and washer, as illustrated in Figure 11. Safety cable Hanger bracket Figure 11 7. MAKE THE ELECTRIC CONNECTIONS POWER LINES 120V Remember to disconnect the power. Follow the steps below to connect the fan to your household wiring. Use the wire connecting nuts supplied with your fan. Secure the connectors with electrical tape.
NOTE: LIGHT KITS ARE AVAILABLE AT YOU SAVOY HOUSE RETAILER. THE FAN IS ALREADY WIRED TO SUPPORT THE LIGHT KIT OPTION. WIRING BOX FAN BLUE BLK WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR OTHER PERSONAL INJURY. MOUNT FAN ONLY ON AN OUTLET BOX OR SUPPORTING SYSTEM MARKED ACCEPTABLE FOR FAN SUPPORT. GREEN GROUND GROUND TO MOUNTING BRACKET OR DOWNROD WH LIGHT WH BLK POWER LINES 120V FAN BLUE WH BLK WH LIGHT Figure 14 Outlet box Screws 8.
. ATTACHING THE FAN BLADES Caution: Remove 5 rubber packing mounts and discard before installation. Step 1. Attach the blade to the blade bracket using the screws and fiber washers as shown in Figure 17. Start screw into bracket. Repeat for the two remaining screws. Screws Step 2. Tighten each screw. Make sure the blade is straight. Fiber washers Step 3. Fasten blade assembly to motor using the screws supplied. (Fig. 17) Blade Screws Blades bracket Figure 17 10.
11. INSTALLING THE LIGHT BULBS & GLASS SHADE 1. Install 2 x 13W compact fluorescent bulbs (provided). (Fig. 19) 2. Remove the decorative nut, glass cap and metal nut from the light kit. Place glass shade over the light kit stem, secure with the metal nut (rubber side on the top)glass cap and decorative nut. Do not overtighten. Secure tightly the glass frame and decorative nut. (Fig. 19) Bulbs Pull Chain Light Kit 3. Insert the 2 pull chain through the eyelet in the shade and cap. (Fig.
13. OPERATING YOUR FAN NOTE: Wait for fan to stop before changing the setting of the slide switch. Turn on the power and check the operation of your fan. The pull chain controls the fan speed as follows: 1 pullHigh, 2 pulls-Medium, 3 pulls- Low, and 4 pulls-Off. Light pull chain it controls the light in "ON" or "OFF". Figure 21 Speed settings for warm or cool weather depend on factors such as the room size, ceiling height, number of fans and so on.
14. TROUBLESHOOTING Problem Solution Fan will not start. 1. Check circuit fuses or breakers. 2. Check line wire connections to the fan and switch wire connections in the switch housing. CAUTION: Make sure main power is off. Fan sounds noisy. 1. Make sure all motor housing screws are snug. 2. Make sure the screws that attach the fan blade bracket to the motor hub is tight. 3. Make sure wire nut connections are not rubbing against each other or the interior wall of the switch housing.
