CEILING FAN OWNER'S MANUAL READ AND SAVE THESE INSTRUCTIONS MODEL: 60-5025-313-13 60-5025-3SV-SN 60-5025-3KO-SN FAN RATING AC 120V.
1. TOOLS AND MATERIALS REQUIRED Philips screw driver Blade screw driver 11 mm wrench Step ladder Wire cutters 2. PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items; a. b. c. d. e. f. g. h. i.
. SAFETY RULES 9. To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning the fan. 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 10. Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly dampened cloth will be suitable for most cleaning. 2.
. MOUNTING OPTIONS If there isn't an existing CUL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support must be able to fully support the moving weight of the fan (at least 50 lbs). Do not use plastic outlet boxes.
. HANGING THE FAN Hanger bracket REMEMBER to turn off the power. Follow the steps below to hang your fan properly: Step 1. Remove the decorative canopy bottom cover from the canopy by turning the cover counter clockwise. (Fig. 5) Ceiling canopy Canopy cover Step 2. Remove the hanger bracket from the canopy by removing the 1 of 2 screws from the bottom of the hanger bracket and loosening the other one a half turn from the screw head.
. INSTALLATION OF SAFETY SUPPORT An additional safety support is provided to prevent the fan from falling. Secure the safety cable to the ceiling joist with screw and washer, as illustrated in Figure 9. Hanger bracket Safety cable Figure 9 7. MAKE THE ELECTRICAL CONNECTIONS Outlet Box Green or bare copper (ground) White (Neutral) WARNING: To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring.
8. FINISHING THE INSTALLATION Outlet box Step 1. Tuck connections neatly into ceiling outlet box. Hanger bracket Step 2. Slide the canopy up to hanger bracket and place the key hole on the canopy over the screw on the hanger bracket, turn canopy until it locks in place at the narrow section of the key holes. Screws Canopy Step 3. Align the circular hole on canopy with the remaining hole on the hanger bracket, secure by tightening the two set screws.
10. INSTALLATING THE MOUNTING PLATE LED Light kit assembly Step 1. Remove the light shade from the LED light kit assembly. (Fig. 13) Step 2. Remove the LED light kit from the mounting plate. (Fig. 14) Light shade Figure 13 Step 3. Remove the 1 of 3 screws from the mounting ring and loosen the other 2 screws. (Do not remove) (Fig. 15) Step 4.
11. INSTALLING THE LED LIGHT KIT & LIGHT SHADE NOTE: Before starting installation, disconect the power by turning off the circuit breaker or removing the fuse at fuse box. Turning power off using the fan switch is not sufficient to prevent electric shock. Step 1. Remove the 1 of 3 screws from the posts of the mounting plate and keep it for future use. Loosen the other 2 screws. (Do not remove) (Fig. 16) Mounting Plate Step 2.
12. OPERATING INSTRUCTIONS F. The " " button is used to set the fan forward or reverse, press the button forward (for warm weather) or reverse (for cool weather). Insert the 3 volt battery (included) and make sure the battery is properly seated with the Positive + sign facing up. (Fig. 17) Your DC motor is equipped with an auto learning type of remote control.
Pairing Process: The auto-learning process will only initiate within the first 60 seconds of supplying power to the fan. Beginning with the fans power off, restore power to the fan. Press and hold the “Fan Off/Set” button for 6 seconds and release. If the optional light kit is installed, the light will blink twice. Once the receiver has detected the frequency, the fan will automatically begin a self-calibration process.
Speed settings for warm or cool weather depend on factors such as the room size. Ceiling height, number of fans and so on. NOTE: To operate the reverse function on this fan, press the reverse button while the fan is running. Warm weather - (Forward) A downward airflow creates a cooling effect as shown in Fig. 20. This allows you to set your air conditioner on a warmer setting without affecting your comfort.
14. TROUBLESHOOTING Problem Solution Fan will not start. 1. Check circuit fuses or breakers. 2. Check line wire connections to the fan and switch wire connections in the switch housing. CAUTION: Make sure main power is off. 3. Check to make sure the dip switches from the transmitter and receiver are set to the same frequency. Fan sounds noisy. 1. Make sure all motor housing screws are snug. 2. Make sure the screws that attach the fan blade bracket to the motor hub is tight. 3.
