SpeedStream 5260 ADSL LAN Modem Installation Guide Part No.
Copyright 1999-2000, Efficient Networks, Inc. All rights reserved. Printed in the U.S.A. Product names mentioned herein may be trademarks and/or registered trademarks of their respective companies. Efficient Networks, Inc. shall not be liable for technical or editorial errors or omissions in this document; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material. Efficient Networks, Inc.
rights of ENI. 8. Licensee Responsibility And Indemnification. The End User understands and acknowledges that it is solely responsible for the use it makes of the Software. Accordingly, the End User agrees to indemnify and hold ENI harmless from any demands, claims or suits by a third party for loss, damages or expenses (including attorney’s fees) arising out of or related to use of the Software by the End User. 9.Enhancements.
Introduction About the 5260 LAN Modem The SpeedStream 5260 ADSL LAN modem provides high-speed connectivity between a local Ethernet network segment and an Asymmetric Digital Subscriber Line (ADSL) segment. The ADSL segment provides for a single Asynchronous Transfer Mode (ATM) permanent virtual circuit (PVC) used for connectivity to Wide Area Network (WAN) devices. The 5260 is designed to “plug and play.
260 Configuration Settings The following table shows the factory-default configuration of the 5260. These settings are not user-configurable.
Hardware Installation Installation Requirements To install the 5260 ADSL LAN modem, you will need the following: • A computer equipped with an Ethernet network interface card (NIC) or an Ethernet hub • A DSL-ready telephone line installed at the desired installation site Package Contents Your package should contain the items listed below. If anything is missing or damaged, please contact the dealer from whom the equipment was purchased.
Installation Instructions NOTE: The labels for the back panel of the 5260 are located on the underside of the unit. 1 Be sure the Power button is in the OFF position. 2 Plug the power cable into the power connection on the back of the unit; then connect it to a power outlet. DSL Connection Power (Out=OFF, In=ON) 6 Ethernet Connection Power Connection 3 Connect the Ethernet port (ENET) on the 5260 to the Ethernet port on your computer using the gray-colored RJ45 cable provided.
5260 Front Panel The 5260 is equipped with four LEDs on the front panel: the System LED (sys), ATM LED (atm), DSL LED (dsl), and Ethernet LED (enet). 1 First, the sys LED will come on. It turns solid green when the unit has finished passing diagnostic tests. 2 The enet LED will then begin to flash green when Ethernet traffic is detected. 3 The 5260 will begin negotiation of the optimum transmission rate and attempt to train the line at the highest rate available.
Table 1 5260 LED Indicator Descriptions LED Unlit Red Yellow Green sys Power not applied Power on self test (POST) error occurred; call customer support to report problem Power on self test (POST) in progress Normal system operation atm • Power not applied ATM diagnostic failure • No ATM cell N/A Blinking: ATM cell delineation and traffic flow Solid: ATM ready Line not yet trained Blinking: Attempting to train line Blinking: Attempting to train line Solid:Line is trained and ready for data
Technical Reference SpeedStream 5260 LAN Modem Specifications Size 5.5W in. x 7D in. x 1.5H in. ( 14W cm x 17.8D cm x 3.8H cm) Weight 1.25 lbs Bridge Only (0.57 Kg) Power Wall-mount 12 watt AC to DC adapter. 12-18vDC @ 1.1 amp output. AC input to meet country specific input requirements. North America: 115 Vac, 60 Hz, .2 amp max Europe: 220 Vac, 50 Hz, .1 amp max Other: 230 Vac, 60 Hz, .
10 SpeedStream 5260 LAN Modem Specifications Efficient Networks, Inc.
