P PECO GRASS COLLECTION SYSTEM DESIGNED FOR: MODEL# 37621219 & 37621220 SCAG TURF TIGER SERIES MOWER OPERATOR’S MANUAL ASSEMBLY MANUAL PART#: Q0344 OPERATION $4.
PECO GRASS COLLECTION SYSTEM TABLE OF CONTENTS SECTION PAGE SECTION Safety - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Safety Alert Symbols - - - - - - - - - - - - - - - - - - - - - - 3 Warranty - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4 I INTRODUCTION AND DESCRIPTION - - - - - - - - - - - - - - 5 1-1 Introduction - - - - - - - - - - - - - - - - - - - - - - - - - 5 1-2 Description - - - - - - - - - - - - - - - - - - - - - - - - - 5 II INSTALLATION FOR USE - - - - - - -
SAFETY WARNING! NEVER operate the unit unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating. WARNING! To avoid serious injury, perform maintenance on the vacuum collector; ONLY AFTER STOPPING THE MOWER’S ENGINE AND WAITING FOR ALL MOVING PARTS TO COME TO A COMPLETE STOP.
PECO LIMITED WARRANTY FOR NEW PRODUCTS A. WHAT IS WARRANTED? PECO extends the following warranties to the original purchaser of each new PECO consumer product subject to the following limitations: 1.
SECTION I INTRODUCTION AND DESCRIPTION 1-1 Introduction Note: If equipped with a Donaldson air cleaner, unit must be rotated to make clearance for top main frame assembly. To rotate Donaldson air cleaner, loosen bolt on air cleaner bracket, rotate air cleaner forward as needed for clearance as shown in Figure 2-1, and tighten. We are pleased to have you as a PECO customer.
2-3 Lift Handle Installation Figure 2-4. The various parts of the handle assembly P#(A0273) must be attached to the container frame. Page 7 shows the orientation and location of the components. Slide the lift handle into the slot in the handle mount bracket P#(B1730) on the grass container. It may be necessary to remove the handle grip P#(J0522) to allow the handle to fit through the slot. Before attaching the handle, hook one end of the spring P#(J0176) into the hole on the underside of the handle.
Lift Handle Assembly Aluminum Grass Container Assembly Aluminum Grass Container With Handle Attached Latch Hook Mechanism Assembly 7
Aluminum Grass Container Exploded View (1) C0025 Box Top (1) C0029 Screen Support (1) B8113 Screen (1) C0023 Box Back & Sides (1) A0938 Box/Door Frame (1) V1131 Plastic Door (4) B1668 Inlet Clamp (1) C1184 Fill Gage (1) V1054 Inlet (1) A0273 Box Handle (1) J0522 Handle Grip (1) B1730 Handle Mount (2) B2526 Linkage Rod (1) B3688 Upper Door Member (1) J0176 Latch Spring (2) K1422 Adjusting Nut (1) A0260 Latch Rod (2) K1435 Adjusting Screw (1) K1442 Adjusting Ball Joint (1)C0024 Box Bottom (1) A0
A0675 UNIT ASSY. (1) V1054 6” PLASTIC INLET (1) 6” x 39” UPPER HOSE (1) A0794 12 CU. FT. BOX ASSY. (1) A0294 LONG THROTTLE KIT FOR (6HP) OR (1) A0060 LONG THROTTLE KIT FOR (5.5HP) (1) 8” x 44” LOWER HOSE (1) E6009 8” BLOWER CONE (1) A0923 MAIN FRAME ASSY. A0674 WEIGHT KIT (1) B2220 WEIGHT (2) J6006 7” - 8” HOSE CLAMPS (1) A00019 ENGINE MOUNT ARM ASSY. (1) A0273 BOX HANDLE ASSY. (1) ENGINE/ BLOWER/ BLADE ASSY. (1) HB0138 HARDWARE BAG (1) HB0251 HARDWARE BAG (1) A0416 OUTER ENGINE MOUNT ASSY.
2-7 Mount Tube Assembly Installation 2-9 Engine/Blower/Blade Assembly Installation Remove the (4) carriage bolts and (4) nuts from the rear plate. See Figure 2-7a. Remove the mower’s rear plate and secure the outer engine mount assembly P#(A0416) to the rear of the mower using the existing (4) bolts and nuts. See Figure 2-7b. Figure 2-7a. Place the engine/blower/blade assembly onto the engine mount arm assembly (Figure 2-9).
2-12 Impeller Blade Removal/Replacement 2-11 Blower Cone Installation Thread (1) 5/16”-18 jam nut P#(K0120) onto each end of (2) 5/16”-18 x 2-1/2” HHCS P#(K0125). Now partially thread the bolts into each of the two tabs located on the blower housing. Place blower cone so the two tabs line up with the bolts then tighten completely. See Figure 2-11. Blower Housing Tabs Figure 2-11. To Remove: First remove the center bolt (#1), washer (#2) and spacer (#3) from the taper-lock bushing (#5). See Figure 2-12.
2-13 Length Of Hose Adjustment 2-16 Lower Hose To Boot Installation The hoses in steps 2-14 and 2-15 must be cut to fit your machine. Follow steps 2-14 and 2-15. Do not cut the hoses until you have tried to fit them on your machine. Remember that the hoses have to be long enough to allow for enough clamping surface between the inlet, blower assembly, and the deck boot, but have to remain short enough to prevent hose “kinks”.
2-18 Throttle Cable Installation Figure 2-18d. To install the throttle cable kit to the box assembly, align the large end of the slot in the throttle base plate (Figure 2-18a) with the rivets located on the front of the box assembly frame (Figure 2-18b). Place the throttle base plate over the rivets, Slide the throttle cable kit to the right, moving the smaller end of the slot over the rivets. When positioned correctly, the throttle spring plate will snap into place (Figure 2-18c).
A. Stop the forward movement of the mower. B. Disengage the mower deck. C. Using the throttle cable slow the engine down to idle. D. Push the dump handle, on the left of the operator, away from the unit. While holding the handle pushed away, move the handle upward. The container door will swing upward and the container will rotate downward. The container will release its contents. E. Once the contents of the container have fallen out, the container is ready to move back into its normal operating position.
Turn any PECO Lawn Vac into a total lawn grooming tool with the PECO Wand Kit! With your PECO Wand Attachment you will double the ability of your PECO Lawn Vac. Using the same powerful vacuum/blower that makes your Lawn Vac work so well, you will be able to get to all those hard-to-reach places where you needed a rake or broom before. SECTION V PARTS AND SERVICE 5-1 Parts And Service Information PECO collection system owners should record the name and telephone number of their Service Center.
SAFETY DECALS To promote safe operation, PECO supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals.
P PECO P.O. BOX 1197 ARDEN, NORTH CAROLINA 28704 (800) 438-5823 OR (828) 684-1234 FAX: (828) 684-0858 EMAIL: peco@lawnvac.com WEBSITE: www.lawnvac.