THIS MANUAL CONTAINS THE OPERATING INSTRUCTIONS AND SAFETY INFORMATION FOR YOUR SCAG ACCESSORY. READING THIS MANUAL WILL PROVIDE YOU WITH MAINTENANCE AND ADJUSTMENT PROCEDURES TO KEEP YOUR ACCESSORY PERFORMING TO MAXIMUM EFFICIENCY. THE SPECIFIC MODELS THAT THIS BOOK COVERS ARE CONTAINED ON THE INSIDE COVER. BEFORE OPERATING YOUR MACHINE, PLEASE READ ALL THE INFORMATION ENCLOSED.
WARNING FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY. * Keep all safety shields in place. * Before performing any maintenance or service, stop the machine and remove the spark plug wire. * If a mechanism becomes clogged, stop the engine before cleaning. * Keep hands, feet and clothing away from power-driven parts. * Read this manual completely as well as the Operator's Manual that came with your mower. * Keep others off the mower (only one person at a time).
1.1 INTRODUCTION 1. Read this operator's manual and the operator's manual that is supplied with the machine this attachment is used on. This manual has been prepared to provide the information you need to correctly assemble, operate, and maintain this grass catcher. Read it carefully and keep it for future reference. A replacement manual is available from your authorized Scag Service Dealer or by contacting: Scag Power Equipment, Service Department at P.O. Box 152, Mayville, WI 53050.
3.1 ASSEMBLY INSTRUCTIONS FOR 48" AND 52" CUTTER DECK 4. Install the grass catcher pulley onto the spindle assembly. Apply loctite to both pulley setscrews and tighten. See Figure 3-1. -NOTEUse the illustrated parts list as a part number reference when following the assembly instructions. 5. Remove the "Custom-Cut" and "Turbo" baffles from the cutter deck. Using the original hardware, install the new "Front" and "Turbo" baffles. See Figure 3-2. 1. Remove all packaging materials.
7. Install the blower assembly to the mounting bracket and secure with the mounting pin. See Figure 3-4. 12. Install the LH & RH hopper mounting brackets to the outside of the frame on the rear of the machine and secure using six (6) 3/8-16 x 1" hex head bolts, and six (6) 3/8-16 elastic stop nuts. See Figure 3-6. Do Not install mounting hardware in the rear holes provided in the RH hopper mounting bracket at this time. LH 8. Align the blower assembly with the discharge opening of the cutter deck.
14. Attach the hood assembly to the machine by installing the mounting post into the hopper mounting brackets. Secure with the ring pins and tighten the locking bolts. See Figure 3-8. Locking Bolts Ring Pins Locking Bolts Ring Pins FIGURE 3-8 15. Install the hose from the blower assembly adapter to the hopper hood and secure using the 6-1/2" clamps. 16. Install the bag assemblies. 17.
4.1 GRASS CATCHER REMOVAL INSTRUCTIONS 1. Prepare the machine so there is easy and safe access to the work area. Remove the key and maintain all safety related work procedures. Always wear eye and hand protection. Loosen Locking Bolts 2. Remove the bag assemblies from the grass catcher. Remove Pins Loosen Locking Bolts 3. Remove the rubber strap holding the adapter to the blower assembly and the large quick pin securing the blower to the discharge mounting bracket. See Figure 4-1.
MAINTENANCE 5.
NOTES 7
GC-STC-V 48" & 52" BLOWER HOUSING ASSEMBLY 9 10 8 4 12 48 1 2 11 49 14 50 13 11 9 11 7 10 47 10 44 14 27 14 12 11 15 43 16 42 26 41 39 18 W FO E B R E E IN V HL O C UA C M A AN M LT 'S E GR B TINATO R LL RAOPE TA E D S PREA IN O 40 14 17 R A N 34 IN G 15 17 R 19 E 3 25 28 20 41 21 38 22 17 35 27 23 5 24 46 14 R D BLOWER ROTATING BLADES BEFORE STOP ENGINE CHUTE ENTERING CAN 24 R E E G W O N L g B vin A D mo D N re A or ER R S g W O ED E nin O R LL D
GC-STC-V 48" & 52" BLOWER HOUSING ASSEMBLY Ref. No. Part Number Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 04067-07 481547 04019-02 04001-59 483392 483393 481428 483223 04024-02 04021-05 04041-07 43277 483209 04021-09 04030-04 424361 04003-05 04001-54 04001-81 04001-21 461928 482379 483189 04043-04 43575 483402 Pin, Ring 2-1/4" Long Lanyard, Deck Height Pin Nut, Serr.
GC-STC-V 48" & 52" BLOWER MOUNTING COMPONENTS UNDER SIDE OF VELOCITY-PLUS CUTTER DECK SHOWN 16 16 10 10 11 5 2 26 25 4 6 23 27 23 28 7 1 24 8 3 25 26 25 6 12 13 24 9 21 14 22 20 15 15 16 18 17 19 RIGHT SIDE OF CUTTER DECK SHOWN 2006 GC-STC-V BMC 10
GC-STC-V 48" & 52" BLOWER MOUNTING COMPONENTS Ref. No.
GC-STC BUCKET SUPPORT COMPONENTS (UPPER) 3 36 37 35 1 6 4 2 5 3 9 11 8 33 4 33 5 23 23 32 21 22 16 5 31 9 13 18 19 9 5 16 21 13 16 18 20 16 24 11 14 16 5 4 5 38 9 35 16 25 17 31 9 34 15 30 27 32 29 26 28 12 40 7 12 10 39
GC-STC BUCKET SUPPORT COMPONENTS (UPPER) Ref. No.
GC-STC BUCKET SUPPORT COMPONENTS (LOWER) 1 2 24 22 23 21 20 19 18 "A" 3 4 5 17 11 6 16 7 15 TO "A" 4 13 4 5 4 8 6 14 7 12 3 4 8 FRAME 6 9 5 6 25 26 9 10 10A STC 2008 BSC 14
GC-STC BUCKET SUPPORT COMPONENTS (LOWER) Ref. No. Part Number Description 1 2 3 4 5 6 7 8 9 10 10A 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 04090-02 482321 423262 04041-07 04021-09 04020-04 04021-05 04067-07 04001-19 461995 461994 04021-02 04001-46 04001-31 482569 423312 451674 04003-02 04001-08 423198 04003-12 423197 04019-03 04040-15 04021-10 04001-32 451969 Pop Rivet, 3/16 x .652 Seal, Hood Tube, Upright Flatwasher, 3/8-.391 x .938 x .
GC-STC-V DECALS 483402 482275 MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING PATENTS: 4,487,006 4,991,382 5,133,176 6,192,666 7,065,946 4,885,903 4,998,948 5,826,416 6,766,633 4,920,733 5,042,239 5,832,708 6,892,519 4,967,543 5,117,617 5,865,018 6,996,962 PATENTS PENDING 483044 481327 483392 483392 483391 483391 483393 483393 16
LIMITED WARRANTY- COMMERCIAL ACCESSORY Any part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag, to be defective in material or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor. The Scag accessory, including any defective part, must be returned to an Authorized Scag Service Dealer within the warranty period.
© 2007 SCAG POWER EQUIPMENT DIVISION OF METALCRAFT OF MAYVILLE, INC. WWW.SCAG.COM PART NO.