Manual

ManualsBrandsScag Power Equipment ManualsGardening equipmentGC-STT-6KH

MODEL GC-STT-6KH

OPERATORS MANUALOPERATORS MANUAL

OPERATORS MANUAL

THIS MANUAL CONTAINS THE OPERATING

INSTRUCTIONS AND SAFETY INFORMA-

TION FOR YOUR SCAG ACCESSORY. READ-

ING THIS MANUAL WILL PROVIDE YOU

WITH MAINTENANCE AND ADJUSTMENT

PROCEDURES TO KEEP YOUR ACCESSORY

PERFORMING TO MAXIMUM EFFICIENCY.

THE SPECIFIC MODELS THAT THIS BOOK

COVERS ARE CONTAINED ON THE INSIDE

COVER. BEFORE OPERATING YOUR MA-

CHINE, PLEASE READ ALL THE INFORMA-

TION ENCLOSED.

PART NUMBER 03065

03054cover

Summary of content (12 pages)

PAGE 1
OPERATORS MANUAL MODEL GC-STT-6KH 71 27 62 50 20 22 18 51 35 34 6 17 15 28 22 17 22 22 28 29 49 19 2 36 14 10 22 60 03054cover THIS MANUAL CONTAINS THE OPERATING INSTRUCTIONS AND SAFETY INFORMATION FOR YOUR SCAG ACCESSORY. READING THIS MANUAL WILL PROVIDE YOU WITH MAINTENANCE AND ADJUSTMENT PROCEDURES TO KEEP YOUR ACCESSORY PERFORMING TO MAXIMUM EFFICIENCY. THE SPECIFIC MODELS THAT THIS BOOK COVERS ARE CONTAINED ON THE INSIDE COVER.
PAGE 2
WARNING FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY. * Keep all safety shields in place. * Before performing any maintenance or service, stop the machine and remove the spark plug wire. * If a mechanism becomes clogged, stop the engine before cleaning. * Keep hands, feet and clothing away from power-driven parts. * Read this manual completely as well as the Operator's Manual that came with your mower. * Keep others off the tractor (only one person at a time).
PAGE 3
® TABLE OF CONTENTS SUBJECT PAGE 1.1 Introduction ........................................................................................................ 1 1.2 Direction Reference .......................................................................................... 1 1.3 Servicing The Engine ......................................................................................... 1 2.1 Safety and Operating Instructions ..................................................................... 1 3.
PAGE 4
1.1 INTRODUCTION 2.1 SAFETY AND OPERATING INSTRUCTIONS This manual has been prepared to provide the information you need to correctly assemble, operate, and maintain this grass catcher. Read it carefully and keep it for future reference. -NoteTo avoid personal injury, it is imperative that all safety instructions be observed. 1. Read this operator's manual and the operator's manual that is supplied with the machine this attachment is used on.
PAGE 5
3.1 ASSEMBLY INSTRUCTIONS -NoteIf you are installing the catcher to a machine with a 52" cutter deck, you must install the filler plate (item 42) to the boot. -NoteFor any instructions referring to an item number, refer to the illustrated parts breakdown on pages 6 and 7. Use the illustrated parts list as a reference when following the assembly instructions. 4.
PAGE 6
3.3 CATCHER FRAME ASSEMBLY 8. Slide the engine support frame (item 54) under the catcher frame and install onto the bolts that are inserted into the RH upright post and the catcher frame. Secure using (2) 3/8-16 elastic stop nuts and (2) 3/8" flat washers. 1. On the LH side of the machine remove the two bolts securing the pump mounting plate to the machine. Align the holes in the hitch bracket weldment (item 53) with the holes in the machine frame.
PAGE 7
6. Align the rear set of holes in the cover bracket weldment with the holes in the RH upright support. Secure the cover bracket to the RH support using (1) 3/8-16 x 2-1/2" bolt, (2) 3/8" flat washers and (1) 3/8-16 elastic stop nut. Do not overtighten. The cover must be allowed to pivot on the upright support. 3.4 BUCKET COVER ASSEMBLY 1. Align the holes in the filter frame (item 74) with the holes in the molded top (item 70). Be sure the venting slots are pointed away from the operator. (see figure 3) 2.
PAGE 8
2. Align the bolts that were inserted through the engine and engine guard weldment with the holes in the engine mounting frame (item 54). Insert all four bolts into the holes in the engine mounting frame and secure using (4) 5/16-18 elastic stop nuts. 3. Attach the engine exhaust deflector (item 64) with the two screws provided, so that the exhaust is deflected downward and at an angle away from the operator. 4.
PAGE 9
GC-STT-6KH GRASS CATCHER 56 69 5 27 21 44 21 74 5 29 27 20 29 9 73 75 70 72 21 27 57 62 38 22 50 20 33 67 18 51 69 35 34 6 37 17 22 17 28 8 52 15 22 28 12 22 28 60 71 22 29 2 32 49 19 36 10 14 7 43 22 55 11 60 A 20 41 40 53 58 21 42 28 29 21 54 22 22 22 2 21 3 4 61 A 65 64 13 61 46 31 48 76 23 24 26 25 GCSTT99EXV 6 45 29 66 7 16 30 39 59 47 63 1
PAGE 10
GC-STT-6KH GRASS CATCHER Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 Part Number 04001-01 04001-09 04001-10 04001-12 04001-14 04001-17 04001-19 04001-20 04001-31 04001-32 04001-38 04001-53 04001-56 04001-71 04001-77 04001-88 04003-12 04020-03 04020-07 04021-08 04021-09 04021-10 04022-02 04030-03 04030-05 04040-11 04040-14 04040-15 04041-07 04062-02 04063-06 04066-03 04067-06 04070-04 422578 422579 422580 422586 Ref. No.
PAGE 11
LIMITED WARRANTY- COMMERCIAL A CCESSOR Y ACCESSOR CCESSORY Any part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag, to be defective in material or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor. The Scag accessory, including any defective part, must be returned to an Authorized Scag Service Dealer within the warranty period.