OPERATOR’S MANUAL Turf Tiger Model: STT61V-31EFI-SS STT-31EFI-SS Congratulations on owning a Scag mower! This manual contains the operating instructions and safety information for your Scag mower. Reading this manual can provide you with assistance in maintenance and adjustment procedures to keep your mower performing to maximum efficiency. The specific models that this book covers are listed on the inside cover. Before operating your machine, please read all the information enclosed.
WARNING FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY OR DEATH. • Read this manual completely as well as other manuals that came with your mower. • DO NOT operate on steep slopes. To check a slope, attempt to back up it (with the cutter deck down). If the machine can back up the slope without the wheels slipping, reduce speed and use extreme caution. • Under no circumstances should the machine be operated on slopes greater than 15 degrees.
Table of Contents R Table of Contents SECTION 1 - GENERAL INFORMATION. ..................................................................................1 1.1 Introduction............................................................................................................................................1 1.2 Direction Reference............................................................................................................................1 1.
Table of Contents R SECTION 6 - ADJUSTMENTS..................................................................................................23 6.1 PARKING BRAKE ADJUSTMENT.............................................................................................................23 6.2 TRAVEL ADJUSTMENTS...........................................................................................................................24 6.3 Throttle Control and Choke Adjustments....................................
Section 1 R GENERAL INFORMATION 1.1 Introduction USE ONLY SCAG APPROVED ATTACHMENTS AND ACCESSORIES. Your mower was built to the highest standards in the industry. However, the prolonged life and maximum efficiency of your mower depends on you following the operating, maintenance and adjustment instructions in this manual. Attachments and accessories manufactured by companies other than Scag Power Equipment are not approved for use on this machine. See Section 8-1.
Section 1 R 1.
Section 2 R SAFETY INFORMATION 2.1 Introduction Danger Your mower is only as safe as the operator. Carelessness or operator error may result in serious bodily injury or death. Hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of the personnel involved in the operation, transport, maintenance and storage of the equipment. Make sure every operator is properly trained and thoroughly familiar with all of the controls before operating the mower.
Section 2 R 7. If the operator(s) or mechanic(s) cannot read English or Spanish, it is the owner's responsibility to explain this material to them. 12. DO NOT add fuel to a running or hot engine. Allow the engine to cool for several minutes before adding fuel. Never fuel indoors or inside enclosed trailers. 8. DO NOT wear loose fitting clothing. Loose clothing, jewelry or long hair could get tangled in moving parts.
Section 2 R 3. Stay two cut widths away from slopes, drop offs, ditches and retaining walls. 15. Disengage power to the attachments when transporting or when not in use. 4. To prevent tipping or loss of control, start and stop smoothly, avoid unnecessary turns and travel at reduced speed. 16. The machine and attachments should be stopped and inspected for damage after striking a foreign object, and damage should be repaired before restarting and operating the machine. 5.
Section 2 R 2.5 Roll-over protection system Lower the roll bar only when absolutely necessary. 1. To lower the roll bar, remove the hairpin cotter pins and remove the two (2) lock pins. See Figure 2-2. WARNING 2. Lower the roll bar to the down position. 3. To raise the roll bar, lift the bar to the upright position. Keep the roll bar in the raised and locked position and the seat belt securely fastened during operation. Failure to do so could cause serious injury or loss of life. 4.
Section 2 R WARNING Failure to properly inspect and maintain the seat belt can cause serious injury or loss of life. 20 o 15 o 10 o 5o 1. Check the full length of the seat belt webbing for cuts, wear, fraying, dirt and stiffness. See Figure 2-3. Figure 2-4. Slope Angle Graph 2. Check the seat belt webbing in areas exposed to ultra violet rays from the sun or extreme dust or dirt.
Section 2 R 2.6 Maintenance Considerations & storage WARNING 1. Never make adjustments to the machine with the engine running unless specifically instructed to do so. If the engine is running, keep hands, feet, and clothing away from moving parts. Hydraulic fluid is under high pressure. Keep body and hands away from pinholes or nozzles that eject hydraulic fluid under high pressure. If you need service on your hydraulic system, please see your authorized Scag dealer.
Section 2 R 2.9 SAFETY AND INSTRUCTIONAL DECALS WARNING INSTALL BELT COvER BEFORE OPERATING MACHINE READ OPERATOR'S MANUAL 483402 483407 483402 483407 FORWARD F R REvERSE 481568 WARNING 483406 Operation of this equipment may create sparks that can start fires around dry vegetation. A spark arrestor may be required. The operator should contact local fire agencies for laws or regulations relating to fire prevention requirements.
Section 3 R SPECIFICATIONS 3.1 Engine General Type.................................................................................................Heavy Duty Industrial/Commercial Gasoline Brand........................................................................................................................................................................Kohler Model...................................................................................................................
Section 3 R 3.4 Cutter Deck Type............................ Floating, Adjustable, Anti-scalping, Hybrid Design Combines Out-front and Belly-mount Designs Construction...........................10-gauge steel reinforced with 7-gauge (3/16") Support Plate. 7-gauge (3/16") deck skirt. True Cutting Width: 61V.........................................................................................................................................................61" (155.0 cm) 72VS...............................
Section 4 R OPERATING INSTRUCTIONS 2. Mower Deck Switch (Figure 4-1). Used to engage and disengage the mower drive system. Pulling up on the switch will engage the deck drive. Pushing down on the switch will disengage the deck drive. CAUTION Do not attempt to operate this mower unless you have read this manual. Learn the location and purpose of all controls and instruments before you operate this mower. 3. Engine Throttle Control (Figure 4-1). Used to control the engine speed.
Section 4 R 5. Hourmeter (Figure 4-1). Indicates the number of hours the engine has been operated. It only operates when the engine is running. Has preset maintenance reminders for engine and hydraulic system oil changes. Will start flashing scheduled maintenance 2 hours before preset time and continue flashing until 2 hours after. Automatically resets. 13. Cutting Height Adjustment (Figure 4-1). Used to set the cutter deck at the desired cutting height. 6. Fuse Holders (Figure 4-1).
Section 4 R 4.3 Initial Run-In Procedures 4.5 Ground Travel And Steering First Day of Use or Approximately 20 Hours - IMPORTANT If you are not familiar with the operation of a machine with lever steering and/or hydrostatic transmissions, the steering and ground speed operations should be learned and practiced in an open area, away from buildings, fences, or obstructions. 1. Check all belts for proper alignment and wear at 2, 4 and 8 hours. 2.
Section 4 R - IMPORTANT - To stop the reverse travel, allow the steering control levers to return to the neutral position. If the mower is to be parked, place the handles in the neutral lock position and engage the parking brake. Do not travel forward over a curb. The mower will hang up on the curb. Raise the deck and travel backwards over the curb at a 45 degree angle. (See Section 4.1, items 13 - 15, on page 14 for cutter deck raising descriptions.) 4.
Section 4 R 4.7 Hillside Operation 4.9 After Operation 1. Wash the entire mower after each use. Do not use high pressure spray or direct the spray onto electrical components. WARNING - IMPORTANT - DO NOT operate on steep slopes. To check a slope, attempt to back up it (with the cutter deck down). If the machine can back up the slope without the wheels slipping, reduce speed and use extreme caution. Under no circumstances should the machine be operated on slopes greater than 15 degrees.
Section 4 R 4.11 Moving Mower With Engine Stopped 4. Keep mower and discharge chute clean. 5. When mowing wet or tall grass, mow the grass twice. Raise the mower to the highest setting for the first pass and then make a second pass to the desired height. To “free-wheel” or move the mower around without the engine running, rotate the dump valve levers counterclockwise. See Figure 4-4. Disengage the parking brake and move the mower by hand.
Section 4 R 3. Insert the lanyard pin into the cutting height index at the desired cutting height. Push forward on the deck lift foot lever, hold in place and pull back on the deck release lever. See Figure 4-6. Slowly release the foot pedal. A deck height decal is located on the cutting height index as an aid in adjusting the deck to the desired height. See Figure 4-5. TENSION kNOB ROTATE LEvER DECK RELEASE LEVER TENSION kNOB G IN TT HT CU EIG H 43 15 48 1.5 1 6 5.5 5 4.5 4 3.5 3 2.
Section 4 R 4.16 Towing (Optional Hitch Accessory) 1. NEVER allow children or others in or on towed equipment. 2. Tow only with a machine that has a hitch designed for towing. Do not attach towed equipment except at the hitch point. 3. Follow manufacturer's recommendations for weight limit for towed equipment. 250 lbs. maximum towing weight. 4. NEVER tow on slopes. The weight of the towed equipment may cause loss of traction and loss of control. 5. Travel slowly and allow extra distance to stop. 6.
Section 5 R TROUBLESHOOTING CUTTING CONDITIONS Condition Cause Stringers - Occasional Low engine RPM Blades of Uncut Grass Width of Deck SGB020 Cure Run engine at full RPM Ground speed too fast Slow speed to adjust for conditions Wet grass Cut grass after it has dried out Dull blades, incorrect sharpening Sharpen blades Deck plugged, grass accumulation Clean underside of deck Belts slipping Adjust belt tension Streaking - Strips of Dull, worn blades Uncut Grass in Cutting Path Incorrect bla
Section 5 R TROUBLESHOOTING CUTTING CONDITIONS (CONT'D) Condition Cause U ne v en C ut on F lat Lift worn from blade Ground - Wavy High-Low Appearance, Scalloped Blade upside down Cut, or Rough Contour Cure Replace blade Mount with cutting edge toward ground Deck plugged, grass accumulation Clean underside of deck Too much blade angle (deck pitch) Adjust pitch and level Deck mounted improperly See your authorized SCAG dealer Bent spindle area See your authorized SCAG dealer Dull blade Sharpen
Section 5 R TROUBLESHOOTING CUTTING CONDITIONS (CONT'D) Condition Cause Scalping - Blades Hitting Low tire pressures Dirt or Cutting Very Close to the Ground Ground speed too fast Width of Deck Cure Check and adjust pressures Slow speed to adjust for conditions Cutting too low May need to reduce ground speed, raise cutting height, change direction of cut, and/or change pitch and level Rough terrain May need to reduce ground speed, raise cutting height, and/or change direction of cut Ground speed
Section 6 R ADJUSTMENTS 6.1 PARKING BRAKE ADJUSTMENT - NOTE If this procedure does not achieve proper brake adjustment, please contact your authorized Scag dealer. WARNING LOOSEN HERE Do not operate the mower if the parking brake is not operable. Possible severe injury could result. The parking brake linkage should be adjusted whenever the parking brake lever is placed in the “ENGAGE” position and the parking brake will allow the mower to move.
Section 6 R 6.2 TRAVEL ADJUSTMENTS LOOSEN HERE Neutral or tracking adjustments will need to be made if: A. The steering control levers are in the neutral position and the machine creeps forward or backward. (Neutral Adjustment). B. The steering control levers are in the full forward position and the mower pulls to one side or the other when traveling in a forward direction. (Tracking Adjustment, See Page 25). ADJUST HERE Neutral Adjustment STT99RHCRA Figure 6-3. RH Steering Control Rod Adjustment 1.
Section 6 R - NOTE - 6. Actuate the steering control levers forward and reverse several times and return them to the neutral position. If after making the adjustment as outlined in step 1A, the machine creeps forward or backward, the neutral adjustment must be made as described on page 24. 7. Check that the drive wheels remained in neutral and readjust if necessary. 8. Check that the steering control levers hit the stop before the pumps reach full stroke. Adjust as needed. 2.
Section 6 R 6.5 BELT ALIGNMENT 2. Loosen the two (2) elastic stop nuts. Adjust the bolt up or down on the adjustment bracket to adjust the cutter deck until the distance from the bottom of the cutter deck to the floor is the same as the measurement on the RH side of the machine. Belt alignment is important for proper performance of your Scag mower. If you experience frequent belt wear or breakage, see your authorized Scag service center for belt adjustment. 3.
Section 6 R - NOTE To prevent the cutter deck from teetering, all four (4) cutter deck hanging chains must have tension on them. If all four chains do not have tension on them and the deck teeters, you must readjust the cutter deck as outlined in the procedures above. DECK STOP Cutter Deck Height 1/4" The cutter deck height adjustment is made to ensure that the cutter deck is cutting at the height indicated on the cutting height index gauge.
Section 6 R 6.7 Custom-Cut Baffle Adjustment To adjust the Custom-Cut Baffle height: 1. Place the cutter deck in the transport position. The Custom-Cut Baffle is designed to deliver optimum airflow and superior cutting performance in any type of grass. The Custom-Cut Baffle can be raised or lowered to precisely tailor the deck's performance for the type of grass being cut. The baffle can be set in seven (7) different positions for optimum performance. 2.
Section 6 R 6.8 electric clutch adjustment ADJUSTMENT NUTS The electric clutch serves two functions in the operation of the mower. In addition to starting and stopping the power flow to the cutter blades, the clutch also acts as a brake to assist in stopping blade rotation when the PTO is switched off or the operator presence circuit is interrupted. When the clutch is disengaged, the air gap between the armature and rotor must be adjusted to fifteen thousandths of an inch, 0.015, for proper operation.
Section 7 R MAINTENANCE 7.1 Maintenance Chart - Recommended Service Intervals HOURS Break-In (First 10) 8 20 40 100 200 Procedure 500 Comments X Check all hardware for tightness X Check hydraulic oil level X C h e c k a l l b e l t s f o r p r o p e r See paragraph 7.8 alignment X Check coolant level See paragraph 7.11 Check hydraulic hoses for leaks Use extreme caution when checking the hydraulic hoses. See paragraph 2.6 X Check engine oil level See paragraph 7.
Section 7 R MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS (CONT'D) HOURS Break-In (First 10) 8 40 100 200 Procedure 500 Comments X Apply grease to fittings See paragraph 7.2 X Check hardware for tightness X Change engine oil filter See paragraph 7.4 X Check hydraulic oil level See paragraph 7.3 X Replace engine fuel filter See paragraph 7.5 X Drain hydraulic system and replace Use SAE 20W50 Motor Oil. hydraulic oil See paragraph 7.
Section 7 R GREASE FITTING LUBRICATION LUBRICANT / INTERVAL LITHIUM MP WHITE GREASE 2125 ( 40 HOURS / WEEKLY ) CHASSIS GREASE ( 100 HOURS / BI-MONTHLY ) CHASSIS GREASE ( 200 HOURS / MONTHLY ) CHASSIS GREASE ( 500 HOURS / YEARLY ) 4 1 3 6 7 5 2 8 1 2 4 9 5 Figure 7-1.
Section 7 R 7.3 Hydraulic System - IMPORTANT The hydraulic oil should be changed if you notice the presence of water or a rancid odor to the hydraulic oil. A. Checking Hydraulic Oil Level The hydraulic oil level should be checked after the first 10 hours of operation. Thereafter, check the oil after every 200 hours of machine operation or monthly, whichever occurs first. 1. Park the mower on a level surface and stop the engine. 2. Place a suitable container under the hydraulic oil filter.
Section 7 R C. Changing Hydraulic Oil Filter Element ENGINE OIL FILTER The hydraulic oil filter should be changed after every 500 hours of operation or annually, whichever occurs first. 1. Remove the oil filter element and properly discard it. See Figure 7-3. Fill the new filter with clean oil and install the filter. Hand tighten only. 2. Run the engine at idle speed with the speed control lever in neutral for five minutes. DRAIN PLUG 3. Check the oil level in the hydraulic tank.
Section 7 R 10. Replace gas cap and tighten securely. For Low Emission (LE) and EPA Phase 3 (produced after 1/1/2011) models, tighten the fuel cap until it ratchets. FILLER NECK INSERT 1/2 . 1/4 . . . E .3/4 F B. Replacing In-Line Fuel Filter Elements FUEL LEVEL The engine fuel filter should be replaced after every 500 hours of operation or annually, whichever occurs first. See Figure 7-7. 1. Close the shut-off valve. 2. Remove the two clamps securing the fuel filter to the fuel hose.
Section 7 R - NOTE - WARNING In extremely dusty conditions it may be necessary to check the element once or twice daily to prevent engine damage. Electric storage battery fluid contains sulfuric acid which is POISON and can cause SEVERE CHEMICAL BURNS. Avoid contact of fluid with eyes, skin, or clothing. Use proper protective gear when handling batteries. DO NOT tip any battery beyond 45° angle in any direction. If fluid contact does occur, follow first aid suggestions below. 1.
Section 7 R WARNING WARNING Always wear proper hand and eye protection when working with cutter blades. BATTERIES PRODUCE EXPLOSIVE GASES. Charge the battery in a well ventilated space so gases produced while charging can dissipate. 3. Check the cutter blades for straightness. If the cutter blades appear bent, they will need to be replaced.
Section 7 R Angle Blade Back HEX NUT-TORQUE TO 75 LB-FT x Do Not Cut In X Must NOT Exceed 1/3 Blade Width 30 SPINDLE SHAFT SGB033 CUTTER DECK Figure 7-8. Blade Sharpening 2. Check the balance of the blade. If the blades are out of balance, vibration and premature wear can occur. See your authorized Scag dealer for blade balancing or special tools, if you choose to balance your own blades. HEX HEAD BOLT / NUT SPINDLE ASSEMBLY CUTTER BLADE SPACER C.
Section 7 R 7.11 Cutter Deck Gearbox 2. Remove the drain plug, drain the lubricant into the container and properly discard it. A. Checking Lubricant Level 3. Re-install the drain plug and add SAE 80W90 lubricant through the check plug hole in the gearbox until it is level with the bottom of the check plug hole. Install the check plug and tighten securely. Caution 7.12 Cooling System The cutter deck gearbox can reach high operating temperatures. Allow the cutter deck gearbox to cool before servicing.
Section 7 R 7.13 Body, Deck, And Upholstery 3. Replace the radiator cap. Push down on the cap and turn clockwise until it stops. - NOTE - Caution The cooling system should be flushed and the coolant replaced every 500 hours of operation or annually. See your Scag dealer for proper coolant replacement. Do not wash any portion of the equipment while it is hot. Do not wash the engine; use compressed air. B. Cleaning the Radiator Debris Screen 1. After each use, wash the mower and cutter deck.
Section 8 R ILLUSTRATED PARTS LIST 8.1 Scag Approved Attachments And Accessories Attachments and accessories manufactured by companies other than Scag Power Equipment are not approved for use on this machine.
Section 8 R 61V & 72VS CUTTER DECKS 3 2 4 5 7 9 6 8 3 17 10 3 11 13 12 1 72V Only 14 15 16 3 4 12 A 7 6 84 83 4 5 7 85 6 5 7 63 11 62 B 61 65 58 23 68 21 22 66 67 71 70 73 20 B 80 54 55 72 24 57 59 23 74 81 25 48 73 79 53 20 23 59 60 57 69 A 6 61 82 20 11 64 48 56 19 12 57 48 18 26 78 75 52 50 77 20 27 76 30 51 36 50 49 38 23 44A 35 37 22 39 28 44 44A 48 14 29 47 43 42 34 30 40 46 6 45 33 31 41 7 32 STT-EFI 2008 CD
Section 8 R 61V & 72VS CUTTER DECKS Ref. No. 1 2 Part No.
Section 8 R CUTTER DECK CONTROLS 41 20 45 8 42 21 36 19 16 25 18 44 22 40 4 6 2 37 10 42 17 14 43 41 5 3 35 9 41 34 30 11 40 33 26 29 32 38 23 7 41 27 40 41 28 13 40 22 31 40 28 15 41 39 26 41 39 40 41 29 24 40 12 24 26 1 CUTTER DECK 44 STT2006CDC
Section 8 R CUTTER DECK CONTROLS Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 Part No.
Section 8 R SHEET METAL COMPONENTS 11 42 44 43 10 15 16 48 13 14 17 9 5 53 1 54 52 8 B 7 54 3 54 12 6 A 46 A 8 19 49 54 B 47 53 22 28 23 15 50 45 26 15 31 32 27 30 12 33 33 29 25 34 36 37 24 35 38 20 4 51 41 39 18 40 18 STT 2011 SMC 4 46 20
Section 8 R SHEET METAL COMPONENTS Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Part No.
Section 8 R STT ROLL-OVER PROTECTION SYSTEM 1 6 10 7 5 7 9 8 11 5 10 6 1 5 11 9 2 2 5 1 4 2 3 4 3 4 3 4 48
Section 8 R STT ROLL-OVER PROTECTION SYSTEM Ref. No. 1 2 3 4 5 6 7 8 9 10 11 Part No. 462210 04001-87 04021-19 04040-13 484168 04001-163 04021-19 425478 484170 484169 484167 Description STT, ROPS Bolt, Hex Head 1/2-13 x 4” Nut, Center Lock 1/2-13 Flatwasher, 1/2-.562 x 1.375 x .109 Pin Assembly (incl.
Section 8 R STT SUSPENSION SEAT 2 3 4 6 5 11 7 4 1 3 2 10 8 13 12 12 12 9 12 Ref. No. 1 2 3 4 5 Part No. 11 9292 04001-178 04040-11 483594 482950 482945 482946 482940 482943 482948 482942 482952 482944 482948 482941 12 13 04001-12 483440 6 7 8 9 10 Description Suspension Seat Assembly w/seat belt Bolt, Hex Head 7/16-20 x 1” Flatwasher, 7/16-.500 x 1.25 x .
Section 8 R NOTES 51
Section 8 R DECK DRIVE COMPONENTS 5 42 6 64 63 62 72 4 59 41 1 2 53 47 46 45 40 47 3 8 43 75 58 74 76 9 55 65 12 45 52 54 7 15 A 61 52 56 52 14 52 52 16 18 13 12 45 45 44 67 10 11 66 45 37 20 17 56 21 45 19 46 45 45 53 58 52 68 48 22 B 23 51 C 70 39 18 24 49 50 38 A 69 B C 73 71 28 29 30 25 26 27 31 36 34 35 Frame 33 32 52 60 73 STT 2005 DDC 57
Section 8 R DECK DRIVE COMPONENTS Ref. No. Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 423925 481531 481309 482845 48030-09 461661 482876 483088 48181 481536 482949 481884 483678 483214 483675 43631 04063-14 48224 481284 482744 482667 461609 43632 461697 481035 43297 481025 481022 43312 43296 48114-04 48677 43644 481022 481024 43534 461608 482438 04012-08 04011-11 04041-07 04069-01 43507 461801 45 04019-04 Ref.
Section 8 R ENGINE & ATTACHING PARTS - 31HP-EFI KOHLER 29 35 25 27 26 28 16 B 1 30 A 3 20 34 11 2 8 5 18 9 10 21 12 4 B 33 31 32 13 A 11 6 14 7 REF. PUMP MTG.
Section 8 R ENGINE & ATTACHING PARTS - 31HP-EFI KOHLER Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Part No. 424910 04017-05 ** 451997 04110-01 483355 482510 483687 04001-19 04030-04 04001-21 04021-09 04001-32 451454 04003-12 04019-03 424691 ** 04002-23 424888 43774 424889 04017-05 04019-02 04040-05 424634 483507 424633 04009-07 462157 43740 483471 04041-11 04041-07 425141 Description Muffler Guard (Kohler) Screw, Hex Serr. Flng.
Section 8 R BRAKE AND STEERING COMPONENTS 1 TO RH PUMP 2 35 37 34 33 TO LH PUMP 36 6 81 4 5 35 31 27 3 76 29 36 28 30 66 82 A 9 75 37 33 25 34 8 17 12 20 38 14 24 39 38 10 11 13 78 6 C 7 A 13 59 59 83 74 56 64 65 61 63 14 24 16 22 79 62 9 26 19 68 9 72 18 22 11 21 5 57 51 11 52 38 21 23 41 80 C 34 40 36 50 48 45 34 47 15 44 67 73 54 49 55 43 60 B 77 B 5 58 5 53 71 45 46 42 69 STT DB&SC 56 70 32
Section 8 R BRAKE AND STEERING COMPONENTS Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 Part No.
Section 8 R STT HYDRAULIC SYSTEM 3 1 DUMP VALVE 5 7 6 D 4 11 12 13 B D 43 (2) 5 4 7 5 6 23 24 26 40 16 4 32 14 A 4 C 27 28 15 43 (2) 46 42 E 44 45 17 B 4 H 5 I 34 25 35 6 4 30 29 30 F A 39 30 22 41 33 9 G G 18 8 20 19 H I 21 31 34 25 35 22 38 Z E D 2 36 10 37 F 2 C 2011 STT HS.
Section 8 R STT HYDRAULIC SYSTEM Ref. No. Part No.
Section 8 R STT-31EFI FUEL SYSTEM - EPA PHASE 3 (models produced after 1/1/2011) 3 Fuel Return 17 To Engine 1 2 18 Tank 33 A 22 23 * 20 21 33 28 18 21 10 35 B B 33 34 To Engine Purge Port Purge 35 A 24 34 33 C 27 26 25 * 10 11 4 Z 11 12 10 9 5 Fuel Tank 16 10 8 C 10 30 31 6 8 32 29 19 28 19 18 Z 7 2011 STT-31EFI FS - EPA Phase 3.
Section 8 R STT-31EFI FUEL SYSTEM - EPA PHASE 3 (models produced after 1/1/2011) Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Part No.
Section 8 R BDP-16A HYDRAULIC PUMP ASSEMBLY WITH COOLING FAN 1 l au rh ve 12 it lK a Se 5 O 11 4 10 6 8 13 9 7 14 2 3 20 PORT "A" SIDE 15 17 OR 30 19 21 16 17 29 18 OR 21 23 22 24 PORT "B" SIDE 20 28 27 26 27 31 32 33 34 36 35 37 62 25
Section 8 R BDP-16A HYDRAULIC PUMP ASSEMBLY WITH COOLING FAN Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 Part No.
Section 8 R ELECTRICAL SYSTEM (31HP-EFI KOHLER) 30 29 B 28 C 1 3 5 4 15 14 6 24 B P 34 C 26 7 S O W E C R E Q A G U IP M E N T 28 A 35 2 20 36 12 37 9 10 18 25 11 33 23 15 20 14 8 16 32 13 21 10 11 22 17 A 31 14 15 17 18 STT2008 ESKH-EFI 64
Section 8 R ELECTRICAL SYSTEM (31HP-EFI KOHLER) Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 Part No.
Section 8 R STT REPLACEMENT DECALS AND INFORMATION PLATES - ALL MODELS __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ 5 1 2 4 FORWARD F 3 Heavy-Duty Commercial R REvERSE 481568 6 481971 7 48404 8 WARNING INSTALL BELT COvER BEFORE OPERATING MACHINE READ OPERATOR'S MANUAL 26 9 25 MOWER DECk PULL OUT TO ENGAGE PUSH IN TO DISENGAGE 10 OFF ON START 24 MOWER D
Section 8 R STT REPLACEMENT DECALS AND INFORMATION PLATES - ALL MODELS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 ** ** Part No.
Section 8 R ELECTRICAL SCHEMATIC (KOHLER 31HP - EFI) VOLT METER PTO SWITCH NEG WATER TEMP SENDER KEY SWITCH POS ENGINE DIAGNOSTIC LIGHT MODULE PLUG WATER TEMP RELAY RED RED BLACK WHITE W/BLK STRIPE GRN W/BLK STRIPE PINK RED BLACK ORANGE BROWN RED RED BLUE LIGHT BLUE RED RED BLACK RED BLACK W/ORANGE STRIPE BLACK RED BRAKE INTERLOCK SWITCH GRN W/WHT STRIPE PINK BLACK CLUTCH 20 AMP FUSE RED WHITE W/BLK STRIPE POS FUEL PUMP NEG DIODE (600V 2A) RED RED BLACK BLACK BLACK
LIMITED WARRANTY - COMMERCIAL EQUIPMENT Any part of the Scag commercial mower manufactured by Scag Power Equipment and found, in the reasonable judgment of Scag, to be defective in materials or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor during the periods specified below. This warranty is limited to the original purchaser and is not transferable. Proof of purchase will be required by the dealer to substantiate any warranty claims.
© 2010 Scag Power Equipment Division of Metalcraft of Mayville, Inc.