! Users / Service manual TopBrewer Pro ! English edition Re-ordering no: x…..
Users / service manual for Scanomat TopBrewer Pro Version 2.03 Vibe Allé 3 • Postboks 131 • 2980 Kokkedal.
Users / service manual for Scanomat TopBrewer Pro Vibe Allé 3 • Postboks 131 • 2980 Kokkedal.
Users / service manual for Scanomat TopBrewer Pro Congratulations on your choice of Scanomat Coffee Brewer. Should you have any questions regarding the coffee brewer and the operation of it please do not hesitate to contact us.
Users / service manual for Scanomat TopBrewer Pro Note: The new detachable hose set supplied with this appliance are to be used at installation, and old hoses are not to be reused. Note: Hose sets shall comply with IEC 61770. Warning: This coffee brewer might be equipped with a Fresh Milk system. Fresh milk is a potential hazardous food, where the safety of the food depends upon the temperature and duration of store, as well as good cleaning and hygienic procedures (HACCP).
Users / service manual for Scanomat TopBrewer Pro Vibe Allé 3 • Postboks 131 • 2980 Kokkedal.
Users / service manual for Scanomat TopBrewer Pro Technical specifications: .............................................................................................................................. 8 Installation:................................................................................................................................................. 10 Table layout (top wiev): ........................................................................................................................
Users / service manual for Scanomat TopBrewer Pro Technical specifications: Power supply: 3 phase 400 VAC with neutral and ground connection. Dimensions: Height: 67,0 cm. Width: 22,5 cm. Depth: 53,5 cm. Water tank: Instant solid state water boiler. Weight: Gross: Nett 44 kg. 41 kg. Water connection: Pressure: 200 kPa (2 Bar) – 600 kPa (6 Bar). Environment: Ambient operation temperature: 10-40° C. Humidity: max. 90% RH. Shelves / transportation: Temperature: min 1° C.
Users / service manual for Scanomat TopBrewer Pro Vibe Allé 3 • Postboks 131 • 2980 Kokkedal.
Users / service manual for Scanomat TopBrewer Pro Installation: The following installations must be provided Electrical single phase (optional) (optional) 230-240 VAC Single phase, 50 Hz, with ground connection, 6500- 7000 W, 28-30 Amp 10 Amp. (priority heating*) 3 Phase (standard) 400 VAC 3 phase with neutral and ground connection, 7000 W, 10 Amp. Water Inlet Pressure 2-6 bar, 200-600 kPa. Flow rate min. 5l./min.
Users / service manual for Scanomat TopBrewer Pro ! Service and repair is only to be carried out by service engineers educated by Scanomat. The coffee brewer is to be secured additionally in accordance with regulations. The coffee brewer must be earth connected (yellow/green conductor). Note: If the supply cable (power cord) has been damaged, please note that only a maintenance engineer recommended by the manufacturer is to renew it, as special tools are required.
Users / service manual for Scanomat TopBrewer Pro The coffee brewer requires ventilation. See “TopBrewer-Pro_Installation-Overview”. The grating must be inspected frequently and vacuum-cleaned. If the installation site/environment is especially dusty there must be vacuum-cleaned each month. Note: Before connecting the coffee brewer draw off some buckets of water by means of the hose (to clean the pipes and to avoid a disagreeable taste).
Users / service manual for Scanomat TopBrewer Pro Water connection: When the water supply is being established please make sure that the coffee brewer is not situated on the rear end of the water supply system to ensure continuous supply of fresh water. 1. Connect the coffee brewer to the cold water line, which is equipped with an adjustable check valve (1/2” external screw thread). Before connecting the brewer draw off some buckets of water to clean the pipes.
Users / service manual for Scanomat TopBrewer Pro Vibe Allé 3 • Postboks 131 • 2980 Kokkedal.
Users / service manual for Scanomat TopBrewer Pro Maintenance: General Drawing A Bean canisters B Canister lid C Program. plug C Main switch D Keyboard E Brewer unit F Brewer unit door G Coffee Funnel H Brewer piston I Piston seal ring J Dreg schraper K Dreg Bin Important: To maintain the high drink quality and efficient operating conditions it is of the utmost importance that all components that are in contact with the drinks are kept clean.
Users / service manual for Scanomat TopBrewer Pro Daily cleaning: Caution: Before starting the cleaning procedure make sure that the coffee brewer is switched off in order to avoid damages and injuries with hot water and moving parts. Make sure to switch the machine off at the machine ON/OFF switch (see point D on the General Drawing).
Users / service manual for Scanomat TopBrewer Pro Unscrew the milk foamer, unscrew the lower part and clean Remove the hose from Milk container and Cleant the tube. Press CLEAN to flush the milk System. Test the coffee brewer. Clean the steam nozzle with the small brush. Clean the milk orifice with the small brush. Refrigerator: Place a jug with milk Place a carafe under cleaner in the fridge and under the outlet. Submerce the tube. Place a jug with cold clean water.
Users / service manual for Scanomat TopBrewer Pro Cleaning the Chocolate system: (optional equipment) Prepare: Fill the rinse bottle with hot water. Close the tap on the chocolate connector Press CHOCOLATE Press the lock to release Remove the connector the chocolate connector. clean the connector. Remove the drip tray clean and refit. Connect the chocolate connector. If chocolate seems to be, and press downwards too thin, squeeze the to feed chocolate into tube at the top connector and pump.
Users / service manual for Scanomat TopBrewer Pro Preventive maintenance: The bean canisters are to be cleaned at regular intervals depending on the performance, usage and type of beans used in the machine. 1) Use hot water with a mild soap solution 2) Remove ingredient canisters. Remember to insert the closing plates. 3) Empty canisters and remove remnants, if any. 4) Clean in soapy water. 5) Re-mount the bean canisters, remove the closing plate and fill up with beans for only one day’s consumption.
Users / service manual for Scanomat TopBrewer Pro Trouble Shooting: Problem Possible cause / solution No operation at all Main switch (D) may be off. DOOR OPEN shows in the display. Close the door. Only water is dispensed No beans in the canisters Make sure grinder is running when selecting a drink FILL WATER shows in the display Check that water supply has been connected, and water supply is open. HEATING shows in the display Press the RESET buttons on the back of the machine.
Users / service manual for Scanomat TopBrewer Pro (See daily maintenance). BOTTOM PISTON ERROR Press STOP, and press YES + CLEAN. NO BEANS shows in display Check the bean canister. Display shows OVERLOAD One of the outputs are overloaded. Milk is not warm enough Clean the steam nozzle and milk orifice. Brewing coffee/espresso very slow. Clean the top piston filter. Adjust the coffee/espresso grinder coarser. Brewing coffee/espresso very fast. Adjust the coffee/espresso grinder finer.
Users / service manual for Scanomat TopBrewer Pro Navigation button: The navigation button is used to access the menu and programming system of your coffee machine. When in adjust mode the UP and DOWN keys have an automatic repeat function. This is activated be holding the key instead of just giving a single press. In that case the adjustment will “run” instead of just step. The Display: ! The display will show relevant information in clear text, and in symbols.
Users / service manual for Scanomat TopBrewer Pro Turning the machine on and off: There are 2 ways of turning the machine off. Either by pressing and holding the ON/OFF button for 2 seconds, or by switching the power off completely by activating the mechanical switch in the dispensing area. Using the first option, will keep the electronic board running with a very low power consumption (less than 1 watt).
Users / service manual for Scanomat TopBrewer Pro While brewing the display will show the name of the selected drink and the number of cups left for this carafe. Pressing STOP or NO any time during a carafe brew will terminate the brewing. Dispensing decaf selections: If the machine is equipped with DECAF coffee, it is able to dispense all selection containing coffee or espresso in a decaf version.
Users / service manual for Scanomat TopBrewer Pro The menu: Using the navigation button, the menu system for accessing all audit data, adjustments and settings of the machine can be reached. Pressing the arrow up and down, YES to enter a function, NO to go back one step, does the navigation through the different menus. Please note that not all menu points described in this manual is available in all machines, as this can vary with different configurations.
Users / service manual for Scanomat TopBrewer Pro Reading out data from the machine: Some data can be read out your coffee machine directly from the keyboard. Number of possibilities may vary from configuration of your machine Press the navigation button UP until following appears: ! Press navigation button YES, and the first adjustable parameter will appear in the display. Pressing UP and DOWN will scroll between the possibilities.
Users / service manual for Scanomat TopBrewer Pro Adjusting the machine: A lot of different parameters in the machine can be adjusted directly from the keyboard. Press the navigation button UP until following appears: ! Press navigation button YES, and the first adjustable parameter will appear in the display. Pressing UP and DOWN will scroll between the possibilities. Adjusting cup sizes: The cup size can be adjusted for each selection independently.
Users / service manual for Scanomat TopBrewer Pro Adjusting drink strength: The drink strength can be adjusted for each product for each selection independently. The preprogrammed strength is referred to as 100% and not as a fixed amount, as it differs from selection to selection. Enter the adjust menu as described above, scroll to: ! Press YES and the display shows: ! Press a selection button and the display shows (example) ! This is pre-programmed amount of COFFEE in the selected drink.
Users / service manual for Scanomat TopBrewer Pro ! Press UP or DOWN to reach the desired value and YES to confirm. Vibe Allé 3 • Postboks 131 • 2980 Kokkedal.
Users / service manual for Scanomat TopBrewer Pro Adjusting carafe: The carafe function is a way to make number of cups of a. selection. Depending on the configuration of your machine, it may have 1, 2 or 3 different carafe sizes (small, medium and large). Note that if the carafe function is not active in your machine, this parameter will not appear in the adjust menu. Enter the adjust menu as described and scroll to: ! Press YES and the display will show: ! S indicating the small carafe.
Users / service manual for Scanomat TopBrewer Pro Adjusting the brew limit: The brew limit is the lowest temperature of the pre heater, where the machine will allow dispensing of drinks. If the temperature of the boiler is below this value, the thermometer icon in the display will be blinking. Enter the adjust menu as described and scroll to: ! Press YES and the display will show: ! Press UP or DOWN to reach the desired value and YES to confirm.
Users / service manual for Scanomat TopBrewer Pro ! Press YES and the display will show: ! Press UP or DOWN to reach the desired value and YES to confirm. A min and max limit for this adjustment is pre-programmed into the machine preventing you from setting the value too low or high. Adjusting version: Your coffee machine MAY be programmed with more than one set (version) of recipes. If this is the case, you can switch between these different set by adjusting the active version.
Users / service manual for Scanomat TopBrewer Pro Adjusting the watch: Your coffee machine is equipped with a watch. The watch is battery backed up, and will maintain working for at least 2 days even if mains power is removed. Enter the adjust menu as described and press UP or DOWN until the display shows: ! Press Yes, and the display will show the current time with the minutes blinking. Adjust these by pressing UP or DOWN and YES to confirm. Adjust the hours in the same way.
Users / service manual for Scanomat TopBrewer Pro Adjusting the timers: Your coffee machine is equipped with 4 programmable timers. These are designed to power the machine down in certain periods. The timers are all 24 hour based, meaning that not weekly or monthly functions are available. Enter the adjust menu as described and press UP or DOWN until the display shows: ! Press YES, and the display will show (example) ! With the minutes blinking.
Users / service manual for Scanomat TopBrewer Pro Machine settings: The machine settings are a lot of different parameters, which can be selected or deselected by you. .
Users / service manual for Scanomat TopBrewer Pro Display watch: Is choosing whether the watch should appear in the display, whenever your coffee machine is in idle mode. Automatic off: If this setting is activated, your coffee machine will automatically turn itself off, if has been inactive for 15 minutes. Cup light: Your coffee machine may be equipped with a light illuminating the dispensed drinks. If this is the case, it can be activated or deactivated by means of this function.
Users / service manual for Scanomat TopBrewer Pro A function to reset the BlueTooth® module. You should carry this function out after consulting a Scanomat technician! BT iOs Support: Must be set to ON if running with Apple devices on the BlueTooth® BT Visible: Must be set to ON, if the machine shall appear as a potential BlueTooth® device on nearby devices with BlueTooth®. BT Pairing: Must be set to ON, if new devices should be able to pair their BlueTooth® with the one of the Scanomat machine.
Users / service manual for Scanomat TopBrewer Pro Service key mode: Service key mode is a mode, which allows extra functions depending of the configuration of your machine. There are a number of possible ways to enter this mode: If your machine is equipped with the quality key system, either based on magnetic cards or contact less TAGS, a service mode key or TAG has been supplied with the machine. If neither, the Service key mode can be obtained by pressing a sequence of buttons on the keyboard.
Users / service manual for Scanomat TopBrewer Pro Vibe Allé 3 • Postboks 131 • 2980 Kokkedal.
Users / service manual for Scanomat TopBrewer Pro Connection chart: ! Vibe Allé 3 • Postboks 131 • 2980 Kokkedal.