IG-300 (BT) 2D Imager Barcode Scanner Quick Guide
Table of contents 1. Introduction ................................................. 1 2. Quick Start .................................................. 2 2.1 Standard Shipment Package ............... 2 2.2 Start Up .............................................. 2 2.3 User’s Manual..................................... 3 3. Program Sequence ...................................... 4 3.1 Factory Default Settings ...................... 4 4. Scanner Imager Mode ................................. 5 5.
1. Introduction Thank you for purchasing this brand-new designed 2D imager hand held barcode scanner. This is a cutting-edge gun-type Area Imaging barcode scanner which is designed specifically for government administration, custom control, shipping industry and etc. That adds on more user friendly functions and has replaceable cable that makes it more easily to be operated by the customers. This high performance gun-type scanner provides the customer with the most cost effective solution in the market.
2. Quick Start 2.1 Standard Shipment Package The standard shipment package is provided with the following items. - 2D Imager Scanner (IG-300 or IG-300BT) Cradle or Charger (optional for IG-300BT) Power Adaptor (if applied) Communication Cable Skip resistant pad Iron panel of cradle and screw Visually inspect the device and accessories for any evidence of physical damage. If anything is missing or appears to be damaged, immediately contact your dealer. 2.2 Start Up A.
Bluetooth MAC address code located on the bottom of cradle. After approximately five seconds your connection is operational and the blue LED on the cradle is on., The scanner with Bluetooth must be charged for a minimum of 8 hours before it can be used. If the battery is full, the red light will be off. 2.3 User’s Manual If you need the further information or more advanced setup options you can contact with your dealer or download the User’s Manual on the service website.
3. Program Sequence You can setup your device by scanning all necessary programming codes for parameters that meet applications. After these scan(s), the device is automatically configured. The Chapter 4 to 9 provides you with the programming codes necessary for a basic setup. For more advanced setup options, please see the User’s Manual 3.1 Factory Default Settings The default RS232 settings are 57600 baud, 8 data bits, and no parity.
4. Scanner Imager Mode The area imager mode allows you to position the hand-held scanner beam in any direction, regardless of the orientation of the barcode, and perform a good read on 1D and 2D barcodes. The linear imager mode allows you to increase your decoding speed while scanning 1D barcodes. However, you need to position the beam across all bars in the 1D barcode.
5. RS232 Parameters (for IG-300 series) 5.1 Baud Rate 38400 <57600> 115200 5.2 Data Bits Data Bits 7 5.
6. USB Parameter (for IG-300 series) USB Mode Attention: The “Set factory default” setting (Chapter 3.1) would return to the original default setting instead of the customized setting. That is, if you are using a USB interface, your device will lose USB interface settings when the “Set factory default” be set. Then you must to re-configure USB mode setting barcode again.
7. Bluetooth Setup (for IG-300BT series) 7.1 Set Cradle Interface Barcode Set Cradle Interface Default Barcode （default RS232, 19200, N-8-1） Set Cradle KB Interface Barcode Set Cradle RS232 Interface Barcode Set Cradle USB HID Interface Barcode 7.2 Bluetooth Default Setting Default Setting 7.
7.4 Sleep Mode Sleep Mode 10 min. ON Sleep Mode OFF 7.
8.
9. Symbologies 9.
Dutch Post ON GS1 CC-A/B ON GS1 CC-C ON GS1 DataBar-Omni ON GS1 DataBar Limited ON GS1 DataBar Expanded ON 12
Infomail ON Interleaved 2 of 5 ON Japan Post ON Matrix 2 of 5 ON MaxiCode ON Micro PDF417 ON MSI ON Planet ON PLESSEY ON Postnet ON QR Code ON 13
Standard 2 of 5 ON Sweden Post ON Telepen ON TLC 39 ON 9.2 Disable All Symbologies. If you want to disable all Symbologies, please scan this programming code.
10. Test Symbologies Scan one or more of these barcodes to test barcode symbologies you enabled.
GS1 DataBar Omnidirectional GS1 DataBar Omni Stacked GS1 DataBar Expanded GS1DataBar Expanded Stacked GS1 DataBar Limited UPC A 0 12345 67890 5 UPC E 0 16 123456 5
11. Specification 11.1 Readable Symbologies 1D Symbologies Symbologies Readable EAN/UPC UCC/EAN128 ISBN ISBT Code 11 Code 39 Code 93/93i Code 128 Interleaved Matrix Instustrial Standard 2 of 5 Codabar MSI Plessey Telepen Postal codes GS1 DataBar Omnidirectional ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ GS1 DataBar Limited ○ GS1 DataBar Expanded ○ Default Enable ○ ○ ○ ○ ○ 2D Symbologies Symbologies Data Matrix PDF 417 Micro PDF 417 Maxicode QR code Aztec EAN.
11.
Cradle Light Red continuous on off Status good read and transmitted power on power off Blue flash continuous on BT disconnect BT connected Green Signal 1 blink 0145-88E0021 V00 19
