IG300BT C1/C2 Area image Barcode Scanner User’s Manual 1
Conents Conents .................................................... 2 1. Introduction......................................... 5 1.1 Safety & Caution .............................. 5 1.2 FCC Warning .................................... 6 2. General Description ............................. 7 2.1 Product Description.......................... 7 2.2 Illustration ......................................... 7 3. Installation .......................................... 8 3.1 Unpacking ..............................
6.1 Factory Default............................... 17 6.2 Scanning Triggering ...................... 17 6.3 Trigger Time Out ............................ 19 6.4 Good Read Mode .......................... 20 6.5 Buzzer Beep Tone ......................... 20 6.5.1 Beep Tone Setup........................ 20 6.5.2 Good Read Beeps ...................... 21 6.5.3 Beep Duration ............................. 21 6.5.4 Timing .......................................... 22 6.5.5 Good Read Duration ..................
7.7.5 Postambles ................................. 48 Appendixes ............................................ 49 A. B. C. D. E. F. Decimal Value Table .................... 49 ASCII Table.................................... 50 Readable Symbologies ............... 51 Technical Specifications............. 52 Scan Map ....................................... 55 Test Symbologies ........................
1. Introduction Thank you for purchasing this brand-new designed 2D imager hand held barcode scanner. This is a cutting-edge gun-type Area Imaging barcode scanner which is designed specifically for retailer, entertainment coupons, medical environment, shipping industry and etc. That adds on more user friendly functions and has replaceable cable that makes it more easily to be operated by the customers.
12) If there are the following situations please contact with the qualified serviceman to check this equipment. 13) The damage of wire or pin of power supply. 14) Some Liquid infiltrate into the equipment. 15) The equipment has been exposed to wet environment. 16) The equipment can’t work well. 17) The equipment has any obvious damage, making the device working abnormally. 18) Don’t storage the device at the temperature lower than -20°C (-4°F) or higher than +70°C (158°F) to avoid any damage. 1.
2. General Description 2.1 Product Description IG300BT is a high performance wireless 2D imager barcode scanner supporting liner, area imager barcode scanning. This device is very easy to configure by this manual, you can set up by scanning all necessary programming codes one time that meet applications, the settings are directly saved permanently, and all settings can be disabled after scan reset factory default. 2.
3. Installation 3.1 Unpacking 1) Take device and its accessories out of the box. 2) Remove the packing material. 3) Check the standard shipment packing list to make sure you have received all of the items ordered. Wireless 2D Imager Scanner Bluetooth Cradle or Charger (optional) Power Adaptor (if applied) Communication Cable Skip resistant pad Iron panel of cradle and screw Quick Start Guide 4) Visually inspect the device and accessories for any evidence of physical damage.
scanner will indicate with red LED and beeper warning. IG300BT Cradle 1) 2) 3) 4) 5) 6) 7) Connect the supplied communication cable at the bottom side of the scanner and you will hear a “click” when the connection is made. Turn off the host system. Connect the other side of the communication cable to the right connector of your Host system. Plug the external power supply into the power jack on the bottom of the cradle. Plug the power supply into the AC outlet. Turn on your Host system.
Cable Installation Connect cable and adaptor to Cradle. The other end of cable will be connected with Host device. Lock the iron panel of Cradle by screwdriver.
4. Set up Bluetooth Communication Before the operation, Bluetooth Communication must be set up between the scanner and cradle. 4.1 Pairing Each scanner has to be linked or paired to a cradle by scanning the unique Bluetooth MAC address code located on the bottom of cradle. The pairing between scanner and cradle is one to one that is one scanner can be paired to a cradle only. 4.2 Set up Master Mode Communication Please follow the steps to set up the communication between the scanner and cradle.
ATTENTION: It is important to know that the scanner will only communicate with the cradle with the unique Bluetooth MAC address. Other scanner can not pair with that cradle until the original connection is broken. If the cradle pairs with another scanner, the cradle will disconnect with the first scanner and then re-connect with another scanner. 4.3 Set up Slave Mode Communication Please follow the below steps to set up the communication between the scanner and Bluetooth application device.
4.4.1 Set Scanner Pin Code Mode Set Default Security Code Set Security Code ON 4.4.2 Set Pin Code Character (PINCODE max. 6 digits/0-9and A-Z ASCII CODE) Set Default Security Code Barcode 1) Begin to Set PINCODE 2) Go to the ASCII Tables in Appendixes; scan 6 labels that represent the PINCODE.
4.5 Bluetooth Cradle Setup 4.5.1 Set Cradle Security Mode Set Default Security Code Barcode Set Security ON 4.5.2 Set Cradle Pin Code (PINCODE max. 6 digits ,0-9,A-Z ASCII CODE ) Set Default Security Code Barcode 1) Begin to Set PINCODE 2) Go to the ASCII Tables in Appendixes; scan 6 labels that represent the PINCODE.
5. Configuring 5.1 Preface How to configure this device: The Barcode Programming Feature gives the possibility to change the scanner settings with use programming codes. 5.2 Changing Scanner Settings with Programming Codes You can setup your device by scanning all necessary programming codes for parameters that meet applications. After these scans, the device will save directly and permanently. To go back to the factory default settings, just scans the programming code factory default.
5.3 Changing Scanner Settings with Utility Tool Manufacturer has setup this scanner with the most common used programming codes, It could be possible that you need more advanced settings to use the scanner without any problems into your application. In this case you can setup your scanner by using the advanced Utility Tool. This tool can be used with the following operation systems: Windows98, Windows2000, Windows XP en Windows Vista. This Utility Tool can be delivered on request.
6. Operating Settings 6.1 Factory Default Set Scanner /Cradle factory default The scanner and cradle factory default settings are shown with bold < > in the following pages. Reset all configuration parameters to their factory default setting. After this reset you must select all required parameters that meet applications. 6.2 Scanning Triggering A reading session begins (lighting and decode processing on) when beam is activated and stops when beam is deactivated.
Flashing Flashing mode allows power up the lighting and decoding are on (no need to activate the trigger line) and after a period of inactivity lasting the time specified by the trigger timeout, the scanner starts flashing, checking for a bar code to be read. When a bar code is detected, the lighting and decoding automatically turn on and stay on until another period of inactivity (timeout), after the timeout the scanner starts flashing again.
Presentation This mode allows power up lighting and decoding are on. After a period of inactivity lasting the time specified by the trigger timeout, the lighting turns off or is dimmed. When a new bar code is presented the lighting and decoding restart and stay on until another period inactivity. 6.
6.4 Good Read Mode When active, the scan engine stops the reading session after a successful decoding. Note: This parameter is NOT used with continuous and continuous + flashing modes. Not Active 6.5 Buzzer Beep Tone 6.5.
6.5.2 Good Read Beeps Two Beeps None 6.5.
6.5.4 Timing Before Transmission After Transmission 6.5.5 Good Read Duration <80 msec> 0.5 sec 1 sec Off 6.5.6 Error Beep Off 6.5.
7. Imager Settings 7.1 Imager Mode You can set the best reading performance depends on the environment, your used application and type of barcodes. Linear mode for decode 1D Barcodes. Area mode for decode 1D and 2D barcodes. Area mode allows you to set the position of the VEGA in any direction regardless of the orientation of the barcode, and perform a good read on 1D and 2D barcodes. Linear mode allows you to increase your decoding speed while scanning 1D barcodes.
7.2 Sleep Mode The scanner is equipped with sleep mode function to save battery energy when the scanner is not used for 1 minute or 10 minute. During sleep mode, all the functions and connection will be halted until pressing the trigger button of scanner to wake up and reconnect the communication with the cradle or Bluetooth device. Sleep Mode 10 min.
7.3 Batch Mode This Batch mode function is enabled when you have scanned “Memory ON” barcode. Scanning data is stored in the memory of the scanner. This function is disabled when you have scanned “Memory OFF” barcode. When you have scanned “Out Of Range” barcode, The scanner transmits the scanning data of work range. In case of the scanner is out of working range, the scanner will store the scanning data to memory.
7.4 Firmware Version Display the firmware version of the scanner, please scan below barcode. 7.4.1 Engine Firmware Version 7.4.2 Scanner Decoder Firmware Version 7.4.3 Cradle Decoder Firmware Version 7.4.4 Scanner Bluetooth MAC Address 7.4.
7.5 Set Cradle Interface Barcode Set Cradle KB Interface Barcode Set Cradle RS232 Interface Barcode 7.6 Cradle RS232 Communication Parameter 7.6.
38400 7.6.2 Cradle Data Bits 7 data bits <8 data bits> 7.6.3 Cradle Stop bits <1 bit> 2 bits 7.6.
Mark Space 7.6.
7.6.
3) Upper/Lower Case Upper Case Lower Case 3) Send Character by ALT Method Enable 4) Select Numerical Pad ON 31
5) Time out Between Characters <0 ms> 5 ms 10 ms 25 ms 50ms 100ms 32
6) Language Selection UK English Italian Spanish French German Swedish Switzerland Hungarian 33
Japanese Belgium Portuguese Denmark Netherlands Turkey Reserved 1 34
7.7 Decoding Selection 7.7.
Codablock A ON Codablock F ON CODE 11 ON CODE 39 OFF 36
CODE 93 ON CODE 128 OFF GS1-128 OFF DATAMATRIX OFF Dutch Post ON 37
EAN-8 OFF EAN-13 OFF EAN 128 OFF GS1 CC-A/B ON 38
GS1 CC-C ON GS1 DataBar-Omni ON GS1 DataBar Limited ON GS1 DataBar Expanded ON Infomail ON 39
Interleaved 2 of 5 ON Japan Post ON Matrix 2 of 5 ON MaxiCode ON 40
MicroPDF417 ON MSI ON PDF417 OFF Planet ON PLESSEY ON 41
Postnet ON QR Code ON QR Code - model 1 ON Standard 2 of 5 ON Sweden Post ON 42
Telepen ON TLC 39 ON UPC-A OFF UPC-E OFF 43
7.7.2 Disable All Symbologies. If you want to disable all Symbologies, please scan below programming code. Or you can scan the “Off” option to disable individual symbologies. Disable All Symbologies Note: Do not reset individual parameters settings for each symbology. When you enable a symbology, you will recover the parameter settings stored in memory. Anytime, you may reset to factory defaults by scanning the programming code of “Set factory default” (please see 7.1.
7.7.3 Multi Code The multicode function is used configure the scanner to read a series of bar codes and then transmit them all at once.
7.7.4 Activates user defined symbology identifier (UDSI) transmission for all symbologies.
EAN-8 FF EAN-13 F GS1-128 C9 GS1 Composite A/B G0 GS1 Composite C G1 GS1 DataBar C3 GS1 DataBar Limited C4 GS1 DataBar Expanded C5 Interleaved 2 of 5 B2 Japan Post P5 Matrix 2 of 5 B4 MaxiCode D2 MicroPDF417 C8 MSI Code B8 PDF417 C7 Planet P1 Plessey Code C2 Postnet P0 QR Code D1 Standard 2 of 5 B5 Sweden Post P7 Telepen C6 TLC 39 H0 UPC-A A0 UPC-E E0 47
7.7.
Appendixes A.
B.
C.
2D Symbologies Symbologies Readable ○ ○ ○ ○ ○ ○ ○ Data Matrix PDF417 MicroPDF417 MaxiCode QR code Aztec EAN.UCC composite Default Enable ○ D. Technical Specifications D-1 Physical Characteristics Weight IG-300BT Scanner Cradle Accessory KBW cable RS232 Cable USB Cable AC adaptor Material Connector Cable Length Dimension Scanner Cradle Approx. 210g Approx. 105g Approx. 75g Approx. 123g Approx. 67g Approx. 125g ABS Plastic RJ 45C 10Pins 5Ft.
Vertical 80°±10% (Left 40°/ Right 40°) Interface IG-300BT KBW, RS-232, USB (HID KBW) b) Bluetooth Characteristics (for IG-300BT series) Bluetooth Module Frequency Band Modulation Method RF Output Power Bluetooth V2.0 Standard 2.402GHz ~ 2.
Blue 2 blink and 2 beeps 2 long blink and 2 long beeps continue on 3 short beeps low Battery warning good read but transmit fail in charging BT disconnect 2 blink per 2 second on connecting BT disconnect before sleep flash 1 blink per 2 second Red Blue Red Green BT connected 1 blink at the same time setting ok and 2 beeps red and green light flash Battery over alternately charged D-4 Electrical Characteristics Operation Voltage Current Operating Current Standby AC transformers 5 VDC ±5% 450 mA (ma
E. Scan Map Symbology Code 39 UPC / EAN Data matrix PDF417 Density 0.125 mm 0.20mm 0.25mm 0.5mm 1mm 0.33 mm 0.191 mm 0.254 mm 0.381 mm 0.16 mm 0.254 mm 0.381 mm 55 Minimum Distance (+/- 10%) 5.2 cm 2.0 cm 2.4 cm 4 cm 7 cm 4 cm 5.3 cm 3.8 cm * 5.2 cm 3.5 cm 3 cm Maximum Distance (+/- 10%) 12.1 cm 21.5 cm 26 cm 44 cm 82 cm 31 cm 16.2 cm 21 cm 28 cm 14.
F. Test Symbologies Scan one or more of these barcodes to test barcode symbologies you enabled.
PDF417 GS1 DataBar Omnidirectional GS1 DataBar Omni Stacked GS1 DataBar Expanded GS1DataBar Expanded Stacked GS1 DataBar Limited UPC A 0 12345 67890 5 UPC E 0 57 123456 5
0145-88E0041 V01 58
