User Manual – RFR100 433MHz TCPIP Reader RFR100 433MHz TCPIP Reader User Manual Revision 02
User Manual – RFR100 433MHz TCPIP Reader User Manual Revision 00 01 02 Date Description 2009.1.15 Preliminary draft 2009.3.19 2009.8.17 Copyright Champtek may have patents, patent applications, trademark, copyrights, or other intellectual property rights covering in this document. The provision of this information does not grant you any license to these patents, trademarks, copyrights, or other intellectual properties. FCC Statement This device complies with part 15 of the FCC Rules.
User Manual – RFR100 433MHz TCPIP Reader Introduction RFR100 433MHz Reader by Champtek is a RFID monitoring system designed to receive all tags data through transmission frequency of 433.92 MHz. It was designed for easy setup, configuration, and usage . RFR100 provides Ethernet interface to communicate with backend host. Host can easily search all available Champtek reader s and setup related parameters.
User Manual – RFR100 433MHz TCPIP Reader Specification Reader Communication Protocol Ethernet 10/100M Fast Ethernet Protocols TCP/IP, UDP, ICMP, ARP, DHCP Client, Telnet Operation frequency 433.92 MHz Signal Strength Default -30dbm Range Control Adjustable RSSI range (0 to -99dbm) Modulation GFSK Read Range Omni Angle Antenna 90m Physical Characteristics Length Width Height Weight Case 4.89” 3.09” 0.
User Manual – RFR100 433MHz TCPIP Reader Mechanicals TOP View Power LED – On when reader is powered. TX/RX LED – On while reader is transmitting or receiving a packet. LAN LED – Blink when there are network activities . Ethernet – RJ-45 Ethernet jack. Antenna – SMA connector Power – 5Vdc Reset Button – Hardware Reset the Reader Network Configuration This section will introduce how to configure the network connection of RFR100 by utility TCPIP.exe RFR100 default IP: 192.168.1.
User Manual – RFR100 433MHz TCPIP Reader Search devices 1. Broadcast Search If don’t know the IP of the device, can utilize broadcast to search all the devices in the LAN to configure the parameters. 2. Search by IP If know the IP of the device not in the same LAN, can search by IP to set the parameters.
User Manual – RFR100 433MHz TCPIP Reader Search result Select anyone of the device and will pop up a dialog to check password.
User Manual – RFR100 433MHz TCPIP Reader Connect to the target device to configure the parameters. Configuration page 1 1. Device Name 2. Network Setting (Notice: Do not change the value the DIO listen port 5001.
User Manual – RFR100 433MHz TCPIP Reader Configuration page 2 1. Reader Operation mode and listen port 2. Serial Setting ( Do not change the default setting) Configuration page 2 1. Change password (Default password is 00000000) 2.
User Manual – RFR100 433MHz TCPIP Reader Utility Upgrade (if needed) Packet Format Head Reader ID Group Tag ID Status RSSI Data $ 000000~999999 00~63 000000~999999 * 00~99 ** End Code 0x0d 0x0a * “Status” indicates the tag ’s condition such as moving, still, etc. ** The content of “Data” depends on different groups of tag. Implementation Notice Keep away from potential RF radiators such as electronic / radio equipments for minimizing inte rference, i.e.
User Manual – RFR100 433MHz TCPIP Reader Recommends CAT-5/5E or CAT-6 high quality Ethernet wire cable for RFR100. RFR100 is typical indoor used, for outdoor environment the Reader can be protected in a NEMA enclosure. The operation performance will be reduced the negatively impacted by nature weather conditions such as moisture, excessive temperature. APIs Champtek also provides efficient C ++ APIs to reduce the time of software development.
User Manual – RFR100 433MHz TCPIP Reader Command API Prototype void param_settimeout(int timevalue) Description Setting the threshold of command timeout Parameter Timevalue[in]: Command timeout Return value None Prototype int prtcl_startdvc() Description Start the reader to transfer the tag data back to the host through Ethernet Parameter None Return Value 0 (Successful) – Successful operation 1 (Time out) – No response 2(Error) – Failed operation Prototype int prtcl_stopdvc() Description
User Manual – RFR100 433MHz TCPIP Reader Prototype int prtcl_resettcp() Description Software reset the Ethernet module Parameter None Return Value 0 (Successful) – Successful operation 1 (Time out) – No response 2 (Error) – Failed operation Comment After reset the Ethernet module, the Ethernet connection will be disconnected. Need to re -connect the reader for further operation.
User Manual – RFR100 433MHz TCPIP Reader Prototype int prtcl_getRSSIrange( unsigned short range ) Description Inquire the RSSI range setting of the read er Parameter range[out]: The receiving RSSI range of the reader Return value 0 (Successful) – Successful operation 1 (Time out) – No response 2 (Error) – Failed operation Prototype int prtcl_getfirmwareversion( char* version ) Description Inquire the firmware version of the reader Parameter version[out]: [Data Format: XX.
User Manual – RFR100 433MHz TCPIP Reader Prototype DWORD data_pop_rssi() Description Get the RSSI message from the buffer Parameter None Return value RSSI message -1: No data in the buffer Prototype DWORD data_group (const char* cmsg, char* pdata) Description Get the group code from a specific packet Parameter cmsg[in]: Tag packet pdata: Group code Return value The length of group code 0: Failed Prototype DWORD data_tagid (const char* cmsg, char* pdata) Description Get the tag id from a
User Manual – RFR100 433MHz TCPIP Reader Prototype DWORD data_data (const char* cmsg,char* pdata) Description Get the data from a specific packet Parameter cmsg[in]: Tag packet pdata: Tag data Return value The length of tag data 0: Failed Prototype DWORD data_readerid (const char* cmsg,char* pdata) Description Get the reader id id from a specific packet Parameter cmsg[in]: Tag packet pdata: Reader ID Return value The length of reader ID 0: Failed Prototype DWORD data_routerid (const char*
