Quick Start Guide VEGA Area Imager V-1020 / V-1020BT Handheld Bar code Scanner
Copyright © 2009, Scantech-ID BV. This manual is copyrighted, with all right reserved. Under the copyright laws, this manual may not, in whole or in part, be copied, Photocopied, reproduced, translated or converted to any electronic medium or machine readable form without prior written consent of Scantech-ID. P/N A270002 V1.
Quick Start Guide Scantech-ID VEGA
Table of contents Chapter 1 Introduction................................................5 Chapter 2 Quick Start 2.1 Standard Shipment Package............................6 2.2 Start up.............................................................6 2.3 Start up with Bluetooth......................................7 2.4 User’s Installation and Programming Manual...7 Chapter 3 Programming Sequence 3.1 Factory Default Settings....................................8 Chapter 4 Scanner Imager Mode 4.1 Imager Mode......
.3 Stop bit ...........................................................12 Chapter 6 USB Parameter………………..………… 13 Chapter 7 Bluetooth Setup for V-1020BT 7.1 Set Cradle Interface Barcode..........................14 7.2 Bluetooth Default Setting.................................15 7.3 Scanner Server/Client Mode...........................15 7.4 Sleep Mode.....................................................16 7.5 Memory Mode.................................................17 Chapter 8 Postambles 8.1 Postamble..
Chapter 11 Specification 11.1 Readable Symbologies..................................27 11.2 Physical Characteristics................................27 11.3 Physical Characteristics Bluetooth Cradle....28 11.4 Operational....................................................28 11.5 Electrical Characteristics(V-1020)................28 11.6 Electrical Characteristics (V-1020BT)..........29 11.7 Bluetooth Characteristics..............................29 11.8 Environmental Characteristics......................
1. Introduction Thank you for purchasing this brand-new designed imager hand held bar code scanner. VEGA is a cutting-edge gun-type Area Imaging barcode scanner which is designed specifically for retail market. To the brand new series of VEGA, we add on more user friendly functions with detachable cable that makes it more easily to be operated by the customers.
2. Quick Start 2.1 Standard Shipment Package The standard shipment package is provided with the following items: a. VEGA Area Imager Handheld Bar code Scanner b. Communication Cable (RS232, PS/2 KBW (V1020BT series only) or USB) c. Power Supply (if applicable) d. Quick Start Guide e. Stand (V-1020) or Bluetooth Cradle (V-1020BT) f. Transparent Cover Plate Visually inspect the VEGA and accessories for any evidence of physical damage.
power supply if applicable. Press the RED trigger button at the top side of the unit; aim the bar code, which covered by the LED red light zone. You will hear a beep and the green LED indicator will light on after scan successfully. 2.3 Start up with Bluetooth Connect the communication cable provided to your POS or Host system and cradle. Power-on the cradle with the provided power supply, scan the Bluetooth MAC address code located on the top side of the cradle.
3. Programming Sequence You can set-up your VEGA by scan necessary programming codes for parameters that meet applications. After these scan(s) the VEGA is automatically configured. The chapters 4 to 9 provide you with the programming codes necessary for a basic setup. For more advanced setup options see VEGA user’s manual. 3.1 Factory Default Settings The default RS232 settings are 57600 baud, 8 data bits, and no parity. The factory default settings are shown with <> and bold in the following pages.
4. Scanner Imager Mode The VEGA Area Imager mode allows you to position the hand held scanner beam in any direction, regardless of the orientation of the bar code, and perform a good read on 1D and 2D bar codes. The VEGA Linear imager mode allows you to increase your decoding speed while scanning 1D bar codes. But, you need to position the beam so that it falls across all bars in the 1D bar codes. 4.
Area mode for Codes With Reflective Surface
5. RS232 Parameters for V1020 5.
5.2 Data bits Data bits 7 5.
6. USB Parameter USB Mode Attention: The “Set factory default” setting would return to the original default setting instead of the customer default setting. If you are using a USB interface, when set to factory default settings, your device will be lost USB interface settings, please reconfigure USB mode setting barcode.
7. Bluetooth Setup for V-1020BT 7.
7.2 Bluetooth Default Setting Default Setting 7.
7.4 Sleep Mode Sleep Mode 10min.
7.
8. Postambles 8.
9. Symbologies 9.
Codablock F ON CODE 11 ON CODE 93 ON CODE 128 ON Dutch Post ON
GS1 CC-A/B ON GS1 CC-C ON GS1 DataBar-Omni ON GS1 DataBar-Limited ON GS1 DataBar-Expanded ON 21
Infomail ON INTERLEAVED 2 of 5 ON Japan Post ON Matrix 2 of 5 ON MaxiCode ON MicroPDF417 ON MSI ON
Planet ON PLESSEY ON Postnet ON QR Code ON Standard 2 of 5 ON Sweden Post ON Telepen ON TLC 39 ON 23
Note: This step does not include codes for all support Barcode symbologies. For a complete overview of support symbologies see the user manual. If you need programming codes for symbologies which are not available in this chapter, please contact Scantech-ID Technical Support department or use VEGA utility tool. 9.
10. Test Symbologies Scan one or more of these bar codes to test bar code symbologies you enabled.
Interleaved 2 of 5 MSI code PDF417 GS1 DataBar Omni directional GS1 DataBar Omni Stacked GS1DataBar Expanded GS1DataBar Expanded Stacked GS1 DataBar Limited UPC A UPC E 0 12345 67890 5 0 123456 5
11. Specification 11.1 Readable Symbologies: 1D / Linear codes: EAN/UPC, GS1 DataBar, Code 39, Code 128, UCC/EAN 128, ISBN, ISSN, Matrix 2 of 5, Interleaved 2of , Codabar , Code 11, Industrial 2 of 5, Code 93/93i, MSI, Standard 2 of 5, Plessey, Postal Codes, Telepen. 2D / Stacked codes: Datamatrix, PDF417, MicroPDF417, Maxicode,QR, Aztec, EAN/UCC composite. 11.2 Physical Characteristics scanner Weight (V-1020) Weight (V-1020BT) Material Connector Dimension Approx 240.gr. (incl cable) Approx 195 gr.
11.3 Physical Characteristics Bluetooth Cradle Weight Material Connector Dimension Approx 150 gr. ABS Plastic RJ 45C 10Pins 129.9mm x 120mm x 71.4mm 11.4 Operational Light Source Visible Red light 650nm Scan rate (Linear mode) 200scans/sec auto adaptive (Area mode) 56 Images/sec auto adaptive Optical resolution 752 x 480 pixels 256 gray levels.
11.6 Electrical Characteristics (V-1020BT) Battery Li-ion Charge Time Reads per charge Cradle LED indicators Operating Current Input Voltage 3.7V / 1400mA 4.5 hours 10,000 Green = good read Blue = Bluetooth function Red / Green = Charging / Charge completed 500 mA 5 VDC @ 2 A / Input AC-100-240V 11.7 Bluetooth Characteristics Bluetooth Module Frequency Band Modulation Method RF Output Power Bluetooth V2.0 Standard 2.40GHz ~ 2.
Scantech-ID BV Nijverheidsweg Noord 60.34 3812 PM Amersfoort The Netherlands Phone: Fax: +31 (0)33 469 84 00 +31 (0)33 465 06 15 E-mail: Internet: info@scantech-id.com www.scantech-id.
