Instruction Manual

www.scarlett-europe.com SC-144
5
GB INSTRUCTION MANUAL
IMPORTANT SAFEGUARDS
· Before the first connecting of the appliance check that voltage indicated on the rating label corresponds to the mains
voltage in your home.
· For home use only. Do not use for industrial purposes. Do not use the appliance for any other purposes than described
in this instruction manual.
· Do not use outdoors.
· Always unplug the appliance from the power supply before cleaning and when not in use.
· To prevent risk of electric shock and fire, do not immerse the appliance in water or in any other liquids.
· Close supervision is necessary when it is used near children or invalids.
· Do not leave the appliance switched on when not in use.
· Do not use other attachments than those supplied.
· Do not operate after malfunction or cord damage.
· Do not attempt to repair, adjust or replace parts in the appliance. Check and repair the malfunctioning appliance in the
nearest service center only.
· Keep the cord away from sharp edges and hot surfaces.
· Do not pull, twist, or wrap the power cord around appliance.
· Never attempt to take food or liquid out from the container when the blade is moving. Always wait until the motor stops
completely.
· Do not overload the appliance with food.
· The appliance operates fast and effective. Do not operate continuously for more than 1 min.
· Never place hot ingredients into processor (> 70 ºC).
FOOD PROCESSOR ASSEMBLING
· Before the first using, wash all removable parts in warm soapy water, rinse thoroughly and dry. Wipe the housing with a
damp cloth.
· Never immerse motor body in any liquid or wash under running water.
· Place the motor unit on a level surface.
· Place the processor bowl onto the bowl shaft. Make sure the three pillars around the bowl shaft are inserted into the
three slots on the bottom of the processor bowl.
ATTACHMENTS
CRUSHING KNIFE (PIC.1)
· Attach the cutting knife and/or plastic blade attachment onto the blade supporter in the bowl.
· Fit the attachment with the adaptor onto the shaft.
· Load products to be processed in the bowl.
· Place lid on the bowl and rotate it to lock.
· Start processing at high speed (position ).
· You can chop up to 1 kg of foodstuff including vegetables, raw or cooked meat or fish.
GRATING / SLICING DISK (PIC.2)
· For grating insert the spindle into the center of the reversible grating/slicing disk side facing up so that the three
protrusions around the spindle penetrate the three slots around the center of the disk. Rotate the disk by gripping the
spindle and go as far as it can in order to lock it into the disk.
· For grating it must be with the grating blade side facing up.
· For slicing turn it over.
· Fit the disk with the spindle onto the shaft.
· Switch speeds control at  (slow speed) to start.
FOOD PROCESSOR USING
· Please make sure accessories are at their places before switching on.
· Plug-in device.
PULSE MODE
· Turn the Speeds control switch to  position.
HOW TO OPERATE
· Before processing cut food so it would pass through a feeder easily.
· Turn control switch to speed "1" (low speed) or "2" / (high speed), so food processor will work continuously until you
turn back to "0" (switch off a speed).
· Gradually feed products to be processed through the feed tube only while processor is operating.
CAUTION: Use the pusher only to feed products, push it evenly and gently. The heavier pressure, the coarser chopping.
· Do not overload the appliance by putting in too much food and do not operate continuously for more than one minute.
· Do not remove any parts during the operating.
· When processing is finished, switch off, and then unplug the appliance and wait till the motor stops before removing
food and attachments.
CLEANING AND CARE
· Switch off and unplug the appliance.
· Wash the accessories immediately and avoid soaking them in water for long periods; wash in warm sudsy water after
each use. Dry all accessories with a clean soft cloth. Do not use a dishwashing machine.
· Wipe housing with a damp cloth.