Product Manual

ManualsBrandsSchaefer ManualsFan Head AccessoriesBig Dog 200/240 Volt Variable Frequency Control

Operating Instructions

SMVector - Frequency Inverter

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.actechdrives.com - Email: info@actechdrives.com

Summary of content (62 pages)

PAGE 1
SMVector - Frequency Inverter Operating Instructions Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.actechdrives.com - Email: info@actechdrives.
PAGE 2
Contents 1 Safety Information..................................................................................................... 3 2 Technical Data........................................................................................................... 6 2.1 2.2 2.3 3 Installation............................................................................................................... 11 3.1 3.2 4 Dimensions and Mounting.......................................................................
PAGE 3
About These Instructions This documentation applies to the SMV frequency inverter and contains important technical data regarding the installation, operation, and commissioning of the inverter. These instructions are only valid for SMV frequency inverters with software revision 4.23 or higher For version 4.23 software, the drive nameplate illustrated below would show “42” in the “F” location. Please read these instructions in their entirety before commissioning the drive.
PAGE 4
Safety Information 1 Safety Information General Some parts of Lenze AC Tech controllers can be electrically live and some surfaces can be hot. Non-authorized removal of the required cover, inappropriate use, and incorrect installation or operation creates the risk of severe injury to personnel and/or damage to equipment.
PAGE 5
Safety Information Explosion Proof Applications Explosion proof motors that are not rated for inverter use lose their certification when used for variable speed. Due to the many areas of liability that may be encountered when dealing with these applications, the following statement of policy applies: Lenze AC Tech Corporation inverter products are sold with no warranty of fitness for a particular purpose or warranty of suitability for use with explosion proof motors.
PAGE 6
Safety Information Harmonics Notification in accordance with EN 61000-3-2, EN 61000-3-12: Operation in public supply networks (Limitation of harmonic currents i.a.w. EN 61000-3-2, Electromagnetic Compatibility (EMC) Limits). Limits for harmonic current emissions (equipment input current up to 16A/phase). Directive Total Power connected to Mains (public supply) Additional Measures Required for Compliance (2) < 0.5kW with mains choke EN 61000-3-2 0.5 ...
PAGE 7
Technical Data 2 Technical Data 2.1 Standards and Application Conditions Conformity CE Low Voltage (2006/95/EC) & EMC (2004/108/EC) Directives Approvals UL508C Underwriters Laboratories -Power Conversion Equipment Input voltage phase imbalance < 2% −− For central grounded systems, operation is permitted without restrictions. −− For corner grounded 400/500V systems, operation is possible but reinforced insulation to control circuits is compromised.
PAGE 8
Technical Data 2.2 SMV Type Number Designation The table herein describes the Type numbering designation for the SMVector Inverter models. ESV 152 N0 2 T X B Electrical Products in the SMVector Series Power Rating in kW: 251 = 0.25kW (0.33HP) 371 = 0.37kW (0.5HP) 751 = 0.75kW (1HP) 112 = 1.1kW (1.5HP) 152 = 1.5kW (2HP) 222 = 2.2kW (3HP) 302 = 3.0kW (4HP) 402 = 4.0kW (5HP) 113 = 11.0kW (15HP) 153 = 15.0kW (20HP) 183 = 18.5kW (25HP) 223 = 22.0kW (30HP) 303 = 30.0kW (40HP) 373 = 37.
PAGE 9
Technical Data 2.3 Ratings 120V / 240VAC Models Mains = 120V Single Phase (1/N/PE) (90...132V), 240V Single Phase (2/PE) (170...264V); 48...62Hz Type Power Hp Mains Current Output Current Heat Loss (Watts) 240V A Cont (In) A Max I % N1/IP31 kW 120V A N4X/IP65 N4X/IP65 No filter W/ filter ESV251--1S-- 0.33 0.25 6.8 3.4 1.7 200 24 ESV371--1S-- 0.5 0.37 9.2 4.6 2.4 200 32 ESV751--1S-- 1 0.75 16.6 8.3 4.2 200 52 41 ESV112--1S-- 1.5 1.1 20 10.0 6.
PAGE 10
Technical Data 240V Three Phase (3/PE) (170...264V); 48...62Hz Type Power Mains Current Output Current Heat Loss (Watts) Cont (In) A Max I % N1/IP31 64 N4X/IP65 N4X/IP65 No filter W/ filter Hp kW 240V A ESV112--2T-- 1.5 1.1 6.9 6 200 ESV152--2T-- 2 1.5 8.1 7 200 75 ESV222--2T-- 3 2.2 10.8 9.6 200 103 ESV402--2T-- 5 4.0 18.6 16.5 200 154 139 ESV552--2T-- 7.5 5.5 26 23 200 225 167 ESV752--2T-- 10 7.
PAGE 11
Technical Data 600VAC Models 600V Three Phase (3/PE) (425...660V); 48...62Hz Type Power Mains Current Hp kW Output Current Heat Loss (Watts) Max I % N1/IP31 A Cont (In) A N4X/IP65 N4X/IP65 No filter W/ filter ESV751--6T-- 1 0.75 2 1.7 200 37 31 ESV152--6T-- 2 1.5 3.2 2.7 200 51 43 ESV222--6T-- 3 2.2 4.4 3.9 200 68 57 ESV402--6T-- 5 4 6.8 6.1 200 101 67 ESV552--6T-- 7.5 5.5 10.2 9 200 148 116 ESV752--6T-- 10 7.5 12.
PAGE 12
Installation 3 Installation 3.1 Dimensions and Mounting WARNING! Drives must not be installed where subjected to adverse environmental conditions such as: combustible, oily, or hazardous vapors; corrosive chemicals; excessive dust, moisture or vibration; direct sunlight or extreme temperatures. 3.1.
PAGE 13
Installation 3.1.2 NEMA 1 (IP31) Models > 30HP (22kW) c b2 b1 s2 b s1 s1 SMV SMV s2 a1 a Type a in (mm) a1 in (mm) b in (mm) b1 in (mm) b2 in (mm) c in (mm) s1 in (mm) s2 in (mm) m lb (kg) K1 ESV303~~4~~B; ESV303~~6~~B 8.72 (221) 7.50 (190) 14.19 (360) 13.30 (338) 0.45 (11.4) 10.07 (256) 0.6 (15) 2.0 (50) 24 (10.9) K2 ESV373~~4~~B; ESV373~~6~~B 8.72 (221) 7.50 (190) 17.19 (436) 16.30 (414) 0.45 (11.4) 10.07 (256) 0.6 (15) 2.0 (50) 31 (14.
PAGE 14
Installation 3.1.3 NEMA 4X (IP65) Models b2 c s2 Mounting Screws 4 x #8-32 10 lb-in 4 x M4 1.2 Nm ( ) b1 b s1 s1 s2 a1 a Type a in (mm) a1 in (mm) b in (mm) b1 in (mm) b2 in (mm) c in (mm) s1 in (mm) s2 in (mm) m lb (kg) ESV371N01SX_; ESV751N01SX_; ESV371N02YX_; ESV751N02YX_; ESV371N04TX_; ESV751N04TX_; ESV751N06TX_; ESV371N02SF_; ESV751N02SF_; ESV371N04TF_; ESV751N04TF_; 6.28 (160) 5.90 (150) 8.00 (203) 6.56 (167) 0.66 (17) 4.47 (114) 2.00 (51) 2.00 (51) 3.6 (1.
PAGE 15
Installation 3.1.4 NEMA 4X (IP65) Models with Disconnect Switch b2 c1 c s2 Mounting Screws 4 x #8-32 10 lb-in 4 x M4 1.2 Nm ( ) b1 s1 s1 b s2 a1 a a in (mm) a1 in (mm) b in (mm) b1 in (mm) b2 in (mm) c in (mm) c1 in (mm) s1 in (mm) s2 in (mm) m lb (kg) 6.28 (160) 5.90 (150) 10.99 (279) 9.54 (242) 0.66 (17) 4.47 (114) .86 (22) 2.00 (51) 2.00 (51) 4.7 (2.13) 6.28 (160) 5.90 (150) 10.99 (279) 9.54 (242) 0.66 (17) 6.31 (160) .86 (22) 2.00 (51) 2.00 (51) 7.9 (3.
PAGE 16
Installation 3.2 Electrical Installation Installation After a Long Period of Storage STOP! Severe damage to the drive can result if it is operated after a long period of storage or inactivity without reforming the DC bus capacitors. If input power has not been applied to the drive for a period of time exceeding three years (due to storage, etc), the electrolytic DC bus capacitors within the drive can change internally, resulting in excessive leakage current.
PAGE 17
Installation 3.2.1.2 Mains Connection to 240VAC Single-Phase Supply PE L1 L2 N PE L1 L2 N ESV...N01S... ESV...N01S... PE L1 L2 PE PE L1 L2 L3 ESV...N02Y... (1/N/PE AC) PE L1 L2 PE PE L1 L2 L1 N PE L1 L2 ESV...N02S... (2/PE AC) ESV...N02S... (1/N/PE AC) PE L1 L2 PE L1 N Mains Connection to Three-Phase Supply ESV...N02Y... ESV...N02T... ESV...N04T... ESV...N06T... (3/PE AC) PE L1 L2 L3 PE 3.2.1.4 N PE L1 L2 L3 ESV...N02Y... (2/PE AC) 3.2.1.
PAGE 18
Installation 3.2.1.5 Installation Recommendations for EMC Compliance For compliance with EN 61800-3 or other EMC standards, motor cables, line cables and control or communications cables must be shielded with each shield/screen clamped to the drive chassis. This clamp is typically located at the conduit mounting plate. The EMC requirements apply to the final installation in its entirety, not to the individual components used.
PAGE 19
Installation 3.2.1.7 Dynamic Brake Connections For NEMA 1 and NEMA 4X Drives rated up to 30HP (22kW) the Dynamic Brake connections are made as illustrated herein. Refer to the SMV Dynamic Brake Instructions (DBV01) for complete information. NEMA 1 (IP31) up to 30HP (22kW) NEMA 4X (IP65) up to 30HP (22kW) + - The SMV 40...60Hp (30...45kW) models include a dynamic brake transistor as standard and only require the connection of an external resistor kit for dynamic braking operation.
PAGE 20
Installation 3.2.2 Fuses/Cable Cross-Sections NOTE: Observe local regulations. Local codes may supersede these recommendations Recommendations 120V 1~ (1/N/PE) 240V 1~ (2/PE) 240V 3~ (3/PE) 400V or 480V 3~(3/PE) 400V or 480V 3~(3/PE) 600V 3~(3/PE) Input Power Wiring (L1, L2, L3, PE) Fuse Miniature circuit breaker(1) Fuse (2) or Breaker(3) (N. America) ESV251N01SXB M10 A C10 A 10 A 1.5 14 ESV371N01SXB, ESV371N01SX* M16 A C16 A 15 A 2.
PAGE 21
Installation Notes for Fuse and Cable Table: (1) Installations with high fault current due to large supply mains may require a type D circuit breaker. (2) UL Class CC or T fast-acting current-limiting type fuses, 200,000 AIC, preferred. Bussman KTK-R, JJN or JJS or equivalent. (3) Thermomagnetic type breakers preferred.
PAGE 22
Installation Control Terminal Strip Descriptions Terminal Description Important 1 Digital Input: Start/Stop 2 Analog Common 5 Analog Input: 0...10 VDC input resistance: >50 kΩ 6 Internal DC supply for speed pot +10 VDC, max. 10 mA 25 Analog Input: 4...20 mA input resistance: 250Ω input resistance = 4.3kΩ 4 Digital Reference/Common +15 VDC / 0 VDC, depending on assertion level 11 Internal DC supply for external devices +12 VDC, max.
PAGE 23
Commissioning 4 Commissioning 4.1 Local Keypad & Display SMV Models: 0.33-10HP (0.25-7.5kW) AUTO SMV Models: 15HP (11kW) and greater FWD REMOTE LOCAL CTRL MAN AUTO RPM Hz % AMPS /UNITS REV RUN AUTO FWD REV RUN STOP STOP 4-Character Display Display 4-Character plus CTRL Display START BUTTON In Local Mode (P100 = 0, 4, 6), this button will start the drive. RUN STOP BUTTON Stops the drive, regardless of which mode the drive is in.
PAGE 24
Commissioning Display INDICATING LEDs (on 4-character display) FWD FWD LED: Indicate the present rotation direction is forward. Refer to ROTATION description above. REV LED: Indicate the present rotation direction is reverse. Refer to ROTATION description above. REV AUTO LED: Indicates that the drive has been put into Auto mode from one of the TB13 inputs (P121…P124 set to 1…7). Indicates that PID mode is active (if PID mode is enabled).
PAGE 25
Commissioning Display START CONTROL The REMOTE/LOCAL LEDs indicate the current start control source. If the start control source is a remote keypad or the network, then both LEDs will be OFF. REFERENCE CONTROL The AUTO/MANUAL LEDs indicate the current reference control source. IF P113 = 0 or 2, the AUTO/MANUAL LEDs will match the AUTO LED on the 4-character display. IF P113 = 0 and no AUTO reference has been setup on the terminal strip, the MANUAL LED will turn ON and the AUTO LED will turn OFF.
PAGE 26
Commissioning 4.3 Parameter Setting Status/Fault messages StoP 60.0 Change Parameters P194 = 0000 M PASS CL Err p100 M p104 15 s 0225 M F.AF F.UF 4.4 20.0 p541 12.0 M 60 s V0106 Electronic Programming Module (EPM) The EPM contains the drives operational memory. Parameter settings are stored in the EPM and setting changes are made to the “User settings” in the EPM. An optional EPM Programmer (model EEPM1RA) is available that allows: • An EPM to be copied directly to another EPM.
PAGE 27
Commissioning 4.5 Parameter Menu 4.5.1 Basic Setup Parameters Code No. Possible Settings Name Default Selection 0 0 Local Keypad P100 Start Control Source 1 Terminal Strip 2 Remote Keypad Only 3 Network Only 4 Terminal Strip or Local Keypad 5 Terminal Strip or Remote Keypad 6 CTRL button select IMPORTANT Use RUN button on front of drive to start Use start/stop circuit wired into the terminal strip. Refer to section 3.2.
PAGE 28
Commissioning Code No. Possible Settings Name Default Selection 0.0 0.0 P102 Minimum Frequency p103 Maximum Frequency 60.0 7.5 IMPORTANT {Hz} P103 {Hz} 500 • P102, P103 are active for all speed references • When using an analog speed reference, also see P160, P161 NOTE • P103 cannot be set below Minimum Frequency (P102) • To set P103 above 120 Hz: - Scroll up to 120 Hz; display shows HiFr (flashing). - Release s button and wait one second. - Press s button again to continue increasing P103.
PAGE 29
Commissioning Code No. Name P110 Start Method Possible Settings Default Selection 0 0 Normal 1 Start on Power-up 2 3 4 5 6 7 8 IMPORTANT Drive will automatically start when power is applied. Start with DC Brake When start command is applied, drive will apply DC braking according to P174, P175 prior to starting the motor Auto Restart Drive will automatically restart after faults, or when power is applied.
PAGE 30
Commissioning Code No. Possible Settings Name Default Selection 0 0 Terminal Strip Control P113 Auto/Manual Control 1 Auto/Manual (CTRL button select) 2 Manual Control Only IMPORTANT The reference is dictated by the settings and state of the TB-13x terminals. If no AUTO reference has been setup on the terminal strip then reference control is dictated by P101. Allows the reference to be switched between auto and manual using the CTRL pushbutton on the drive keypad.
PAGE 31
Commissioning 4.5.2 I/O Setup Parameters Code No.
PAGE 32
Commissioning Code No. Possible Settings IMPORTANT Name Default Selection NOTE • When input is activated, settings 1...7 override P101 • When TB-13A...TB-13D are configured for Auto References other than MOP, TB-13D overrides TB-13C, TB-13C overrides TB-13B and TB-13B overrides TB-13A. Any other Auto Reference will have priority over MOP. • Settings 10...
PAGE 33
Commissioning Code No. Name p140 Relay Output TB-16, 17 Possible Settings Default Selection 0 0 None 1 Run 2 Reverse 3 Fault 4 Inverse Fault 5 Fault Lockout 6 At Speed 7 8 9 10 Above Preset Speed #6 Current Limit Follower Loss (4-20 mA) Loss of Load 11 12 13 14 15 16 Local Keypad Control Active Terminal Strip Control Active Remote Keypad Control Active Network Control Active Standard Reference Active Auto Reference Active 17 18 19 20 21 22 Sleep Mode Active PID Feedback < Min.
PAGE 34
Commissioning Code No. Name P144 Digital Output Inversion Possible Settings Default Selection P144 0 1 2 3 p145 Loss of Load Threshold p146 Loss of Load Delay p149 Analog Output Offset p150 TB-30 Output IMPORTANT Invert P142 NO NO YES YES Invert P140 NO YES NO YES 0.0 NOTE Inverting P140 or P142 when the parameter is set to NONE (0) will result in the output being energized continuously. NOTE For SMVector drives rated at 0.33 to 10 HP (0.25 to 7.
PAGE 35
Commissioning 4.5.3 Advanced Setup Parameters Code No. Name p156 Analog Inputs Configuration p157 TB5 (0-10V) Analog Possible Settings Default Selection 0 0 TB5: (0-10 VDC); TB25: (4-20mA) 1 TB5: (0 - 5 VDC); TB25: (4-20mA) 2 TB5: (2 - 10 VDC); TB25: (4-20mA) 4 TB5: (0-10 VDC); TB25: (0-20mA) 5 TB5: (0 - 5 VDC); TB25: (0-20mA) 6 TB5: (2 - 10 VDC); TB25: (0-20mA) 0 0 No Action 0.0 Selects the reaction to a loss of the 0-10V signal 1 If TB5 < P158 - Trip Fault F.
PAGE 36
Commissioning Code No. P165 Name TB-25 (4-20mA) Analog Input Monitoring Level Base Voltage P166 Carrier Frequency P164 Possible Settings Default Selection 2.0 0.0 15 IMPORTANT {mA} 20.0 {V} 1000 See Notes 0 1 2 3 60.0 10.0 {Hz} 1500 Fixed Boost 0.0 {%} 40.0 p169 Accel Boost 0.0 NOTE • P167 = rated motor frequency for standard applications • P165, P168 = default setting depends on drive rating 0.0 {%} 20.0 Accel Boost is only active during acceleration P170 Slip Compensation 0.
PAGE 37
Commissioning Code No. Name DC Brake Time p175 p176 p177 (2) Keypad Setpoint Single Press Increment Speed Units Possible Settings IMPORTANT Default Selection 0.0 0.0 {s} 999.9 NOTE: CONFIRM MOTOR SUITABILITY FOR USE WITH DC BRAKING DC Brake voltage (P174) is applied for the time specified by P175 with the following exceptions: • If P111=1, 3 and P175=999.9 the brake voltage will be applied continuously until a run or fault condition occurs. • If P110=2, 4…6 and P175=999.
PAGE 38
Commissioning Code No. p190 Name Motor Braking Possible Settings Default Selection 0 Disabled 1 Braking with BUS threshold 2 Braking always on with deceleration 3 Braking with bus regulator p191 Motor Brake Level 0 IMPORTANT Flux brake OFF. When drive is in deceleration and Vbus > Vdeceleration freeze (114% of the rated Vbus), the flux brake will be turned ON. As long as drive is in deceleration, the flux brake will be ON.
PAGE 39
Commissioning Code No. Name Program Selection p199 4.5.4 Code No. PID Parameters Name PID Mode P200 Possible Settings IMPORTANT Default Selection NOTE 4 Resetting to 50 and 60 Hz default settings will set the Assertion Level (P120) to “2” (High). P120 may need to be reset for the digital input devices being used. An F.AL fault may occur if P120 and the Assertion switch are not set identically.
PAGE 40
Commissioning Code No. Possible Settings Default Selection 5.0 0.0 IMPORTANT p207 Name Proportional Gain {%} 1000.0 p208 Integral Gain 0.0 0.0 {s} 20.0 p209 Derivative Gain 0.0 0.0 {s} 20.0 NOTE • • 0.0 Used to tune the PID loop: • Increase P207 until system becomes unstable, then decrease P207 by 10-15% • Next, increase P208 until feedback matches setpoint • If required, increase P209 to compensate for sudden changes in feedback p210 PID Setpoint Ramp 20.0 p214 Minimum Alarm 0.
PAGE 41
Commissioning Code No. P252 Possible Settings Default Selection 0 0 Disabled 1 Enabled Time Delay between 30.0 0.0 Auto Rinses Auto Rinse Speed 0.0 -500.0 P253 Auto Rinse Time 0.0 0.0 {sec} 6553.
PAGE 42
Commissioning Code No. p304 P305 P306 (1) (1) Name Motor Rated Frequency Motor Rated Speed (1) Motor Cosine Phi P310 (1) p311 (1) Motor Stator Resistance Motor Stator Inductance Dead Time Compensation Factor Torque Limit P315 P330 P331 P399 (1) (2) 1000 {RPM} 65000 300 0.80 100 0.40 0.99 NOTE If motor cosine phi is not known, use one of the following formulas: cos phi = motor Watts / (motor efficiency X P302 X P303 X 1.
PAGE 43
Commissioning 4.5.6 Network Parameters Code No. Possible Settings Default Selection 0 Not Active 1 Remote Keypad 2 Modbus RTU 3 CANopen 4 DeviceNet 5 Ethernet 6 Profibus 7 Lecom-B 8 I/O Module 0 0 No Module Installed p401 Module Type Installed 1 Basic I/O (0x0100, 1.0.0) 2 RS485/Rem. Keypad (0x0200, 2.0.0) 3 CANopen (0x0300, 3.0.0) 11 PROFIBUS (0x1100, 11.0.0) 12 Ethernet (0x1200, 12.0.
PAGE 44
Commissioning 4.5.7 Diagnostic Parameters Code No. Display Range (READ ONLY) Name p500 Fault History IMPORTANT • Displays the last 8 faults • Format: n.xxx where: n = 1..8, 1 is the newest fault; xxx = fault message (w/o the F.) • Refer to section 5.3 Format: x.yz P501 Software Version P502 Drive ID A flashing display indicates that the Drive ID stored in the EPM does not match the drive model it is plugged into.
PAGE 45
Commissioning Code No. p560 p561 p562 p563 p564 Name Sequencer: Currently Active Segment Sequencer: Time since Start of Active Segment Sequencer: Time Remaining in Active Segment Sequencer: Number of cycles since start Sequencer: Number of cycles remaining Display Range (READ ONLY) IMPORTANT 0 17 0.0 0 {P708} {P708} 6553.5 65535 Unit depends on P708 (0.1sec, sec or minutes) 0.0 0 {P708} {P708} 6553.5 65535 Unit depends on P708 (0.
PAGE 46
Commissioning 4.5.8 Onboard Communications Parameters 15-60HP (11-45kW) The P6xx Onboard Communication parameters are applicable to the 15HP (11kW) and higher models only. Code No. Possible Settings IMPORTANT Default Selection 0 0 Disabled This parameter enables the onboard network communications.
PAGE 47
Commissioning 4.5.9 Sequencer Parameters The P700 Sequencer parameters are listed herein. Refer to section 4.5.7 for P56x Sequencer Diagnostic Parameters. The sequencer function consists of 16 step segments, each individual step segment can have its own ramp time, time spent in individual segment and output frequency entered. The sequencer has 3 different modes to control how the drive moves through each individual step segment: Timer Transition, Step Sequence or Timer and Step Sequence.
PAGE 48
Commissioning Code Possible Settings No. Name P708 Sequencer: Time units/scaling IMPORTANT Default Selection 0 0 0.1 {sec} 6553.
PAGE 49
Commissioning Code Possible Settings IMPORTANT No. Name Default Selection P720 Segment #3 Frequency Setpoint 0.0 -500.0 {Hz} 500.0 P721 Segment #3 Accel/Decel Time 20.0 0.0 {sec} 3600.0 P722 Segment #3 Time in current step 0.0 0 0.0 0 {P708} {P708} 6553.
PAGE 50
Commissioning Code Possible Settings IMPORTANT No. Name Default Selection P735 Segment #6 Frequency Setpoint 0.0 -500.0 {Hz} 500.0 P736 Segment #6 Accel/Decel Time 20.0 0.0 {sec} 3600.0 P737 Segment #6 Time in current step 0.0 0 0.0 0 {P708} {P708} 6553.
PAGE 51
Commissioning Code Possible Settings IMPORTANT No. Name Default Selection P750 Segment #9 Frequency Setpoint 0.0 -500.0 {Hz} 500.0 P751 Segment #9 Accel/Decel Time 20.0 0.0 {sec} 3600.0 P752 Segment #9 Time in current step 0.0 0 0.0 0 {P708} {P708} 6553.
PAGE 52
Commissioning Code Possible Settings IMPORTANT No. Name Default Selection P765 Segment #12 Frequency Setpoint 0.0 -500.0 {Hz} 500.0 P766 Segment #12 Accel/Decel Time 20.0 0.0 {sec} 3600.0 P767 Segment #12 Time in current step 0.0 0 0.0 0 {P708} {P708} 6553.
PAGE 53
Commissioning Code Possible Settings IMPORTANT No. Name Default Selection P780 Segment #15 Frequency Setpoint 0.0 -500.0 {Hz} 500.0 P781 Segment #15 Accel/Decel Time 20.0 0.0 {sec} 3600.0 P782 Segment #15 Time in current step 0.0 0 0.0 0 {P708} {P708} 6553.
PAGE 54
Commissioning Code Possible Settings No. Name P794 End Segment: TB30 Analog Output Value P795 End Segment: Drive Action IMPORTANT Default Selection 0.00 0 0.00 {VDC} 0 Keep Running 1 Stop (based on P111) 2 Coast to Stop 10.00 TB30 configuration parameter must be set to accept this value: P150 = 10 Recovery: Toggling the START SEQUENCE will start the cycle from ‘end segment Stop’ or ‘end segment DC Brake’.
PAGE 55
Commissioning 4.5.9.1 Sequencer Flow Diagram Left Sequencer Flow Diagram “Start Segment” number selection (2) Start from Terminal Strip P100 P700 24 Start Segment P703 Start from Network (SMV communications module) WARNING If none of the digital inputs (TB-13A,B,C or D) are asserted but a start signal is given from the Start/Stop source (P100) then the drive will run at the output frequency value governed by the frequency reference source (P101).
PAGE 56
Commissioning 4.5.9.2 Sequencer Flow Diagram Right Action after Stop/Start (P100) transition/digital input (if setup for sequencer mode) transition or restart after trip.
PAGE 57
Commissioning 4.5.9.
PAGE 58
Troubleshooting and Diagnostics 5 Troubleshooting and Diagnostics 5.1 Status/Warning Messages Status / Warning br bf DC-injection brake active Drive ID warning CAL Motor Auto-calibration active cE CL Cause DC-injection brake activated • activation of digital input (P121...P124 = 18) • automatically (P110 = 2, 4...6) • automatically (P111 = 1, 3) The Drive ID (P502) stored on the EPM does not match the drive model.
PAGE 59
Troubleshooting and Diagnostics 5.2 Drive Configuration Messages When the Mode button is pressed and held, the drive’s display will provide a 4-digit code that indicates how the drive is configured. If the drive is in a Stop state when this is done, the display will also indicate which control source commanded the drive to Stop (the two displays will alternate every second). Configuration Display Format = x.y.
PAGE 60
Troubleshooting and Diagnostics Fault f.dbF Dynamic Braking fault f.EF External fault f.F1 EPM fault Cause Remedy (1) Dynamic braking resistors are overheating • Increase active decel time (P105, P126, P127). • Check mains voltage and P107 • P121…P124 = 21 and that digital input • Correct the external fault condition has been opened. • Make sure digital input is set properly for NC • P121…P124 = 22 and that digital input or NO circuit has been closed.
PAGE 61
Troubleshooting and Diagnostics Fault f.
PAGE 62
Appendix Appendix A A.1 Permissable Cable Lengths The table herein lists the permissable cable lengths for use with an SMV inverter with an internal EMC filter. NOTE This table is intended as a reference guideline only; application results may vary. The values in this table are based on testing with commonly available low-capacitance shielded cable and commonly available AC induction motors. Testing is conducted at worst case speeds and loads.