operation manual

L
WA
sound power level
measured
86.5 dB(A) 88.9 dB(A)
K
WA
uncertainty 3 dB(A 3 dB(A)
L
WA
sound power level gu-
aranteed
92 dB(A) 93 dB(A)
Wear ear-muff s.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions)
determined in accordance with ISO 22867.
Hedge
Trimmer
Pole Saw
Vibration emission value a
h
2.87 m/s
2
1.635 m/s
2
Unsicherheit K uncertainty 1.5 m/s
2
1.5 m/s
2
The speci ed vibration value was established in ac-
cordance with a standardized testing method. It may
change according to how the electric equipment is
used and may exceed the speci ed value in exceptio-
nal circumstances.
The specied vibration value can be used to compare
the equipment with other electric power tools.
The speci ed vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a mi-
nimum.
• Only use appliances which are in perfect working or-
der.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.
Before starting the equipment
Caution! Do not  t the battery until the equipment has
been fully assembled and all the settings have been ac-
tuated. Always wear protective gloves when working on
the equipment to protect yourself against injury. Careful-
ly unpack all parts and check that they are complete.
Assembly
Fitting the chain saw mounting kit (for use as a pole-
operated pruner)
Assembly of the cutter rail and the saw chain
• Undo the xing screw (17) of the chain wheel
• cover (Fig. 2).
• Take off the chain wheel cover (18). (Fig.3)
• Lay the chain as shown in the groove which runs
around the cutter rail (Fig. 4/Item 19).
• Insert the cutter rail and chain as shown in the moun-
ting in the chainsaw (Fig. 5).
• At the same time guide the chain around the chain
wheel (Fig. 5/Item 20).
• Attach the chain wheel cover (Fig. 6/Item 18) and
fasten it hand-tight with the fastening screw.
Important! Do not fully tighten the fastening screw until
after you have adjusted the chain tension.
The accumulator must be packaged (plastic bag, box)
or accumulator contacts must be sealed up for accu-
mulator disposal, transport or storage.
Residual risks
Even when the device is used properly and all safety
regulations are complied with, there still may be some
residual risks.
• Cutting injury
• Hearing damage
• A longer stay in the immediate vicinity of the running
unit may cause hearing damage. Wear ear protec-
tors!
• Damage to health arising from vibrations to hand
and arms if the device is used for a long time or if
the device is not guided and evaluated properly.
Despite the observance of the operating instructions
there still may be some hidden residual risks.
Technical data
Pole Saw
Cutter bar length 240 mm
Max. Cutting length 200 mm
Chain pitch 3/8“
Chain thickness 1.3 mm
Sprocket wheel 6 Teeth, 3/8“
Cutting speed at rated
rpm:
4 m/s
Oil tank capacity 0.09 l
Saw chain Oregon 91P033X
Cutter bar Oregon 080NDEA318
Hedge Trimmer
Max. cutting length 410 mm
Tooth spacing 15 mm
Cuts 1250 /min
Cutting Diameter max. 15 mm
Lithium-ion battery
Voltage 18 V
Capacity 1500 mAh
Charging time 75 min
Charging unit
Input voltage 100-240 V / 50-60 Hz
Power rating 40 W
Output voltage 21 V
Output current 1.5 A (h)
Protection Class II
Sound and vibration
Sound and vibration values were measured in ac-
cordance with ISO 22868.
Hedge
Trimmer
Pole Saw
L
pA
sound pressure level 76.6 dB(A) 68.9 dB(A)
K
WA
uncertainty 3 dB(A 3 dB(A)
23 І 52