P516-098 WIRELESS PORTABLE READER (WPR) INSTRUCTIONS FOR WPR400 Para el idioma español, navegue hacia www.schlage.com/support. Pour la portion française, veuillez consulter le site www.schlage.com/support.
WPR400 Wireless Portable Reader User Guide CONTENTS Overview........................................................................................................................................ 3 Getting Started .............................................................................................................................. 3 WPR400 Operation ....................................................................................................................... 4 WPR400 Range ...............
WPR400 Wireless Portable Reader User Guide OVERVIEW The WPR400 is a Wireless Access Point Module (WAPM) designed to interface with access control panels through a PIM400. The WPR400: • Communicates with the PIM400 via RF (radio frequency). • May be linked only to a PIM400. • Is powered with rechargeable batteries. • May be used with all credential readers in the AD-Series product line. • When attached to a credential reader, normally operates in on-line (Reader) mode.
WPR400 Wireless Portable Reader User Guide WPR400 OPERATION WPR400 Range For optimum performance, the WPR400 should be operated within the following range limits: • Maximum distance between the PIM400 and WPR400 is 200 feet (61 meters) horizontally on the same floor in a building with normal construction materials. • For a line-of-sight installation, maximum distance is 1000 feet (305 meters). Connecting a Reader to the WPR400 (if necessary) 1. Connect the reader cable to the reader as shown below. 2.
WPR400 Wireless Portable Reader User Guide Permanently or Temporarily Mount the WPR400 • Mount the WPR400 using screws or Velcro® strips. • The WPR400 should always be mounted at least one inch away from any metallic surface. • Place the WPR400 in a position where it was successfully link tested. Permanent mount with screws: 1. Remove the WPR400 cover. 2. Using the base as a template, mark the mounting holes. 3. Drill a hole at each mark and use a wall anchor and screws (not provided) to attach the WPR400.
WPR400 Wireless Portable Reader User Guide SCHLAGE UTILITY SOFTWARE (SUS) The SUS can be used to configure credential reader settings. For information about the SUS and credential reader settings, see the SUS User Guide at www.schlage.com/support. To start communication with the SUS: 1. Turn off the WPR400 power switch. 2. Loosen the 4 screws and remove the WPR400 cover. 3. Connect the USB communication cable to the WPR400 USB port. USB Port 4. Log in to the SUS software. (See the SUS User Guide at www.
WPR400 Wireless Portable Reader User Guide LINK TO A PIM400 (READER MODE ONLY) Each time it is turned on, the WPR400 will check the quality of its link to a PIM400, if a link had previously been made. If the previous link to a PIM400 cannot be re-established or it does not exist, the WPR400 will automatically attempt to link to a PIM400. Only one WPR400 or other WAPM can be linked at a time. Ensure that no other PIM400s are in link mode during this process. 1.
WPR400 Wireless Portable Reader User Guide CHANGE THE RF CHANNEL ! Changing the RF channel will terminate links with other WAPMs previously linked to the PIM400. The WPR400 radio frequency (RF) channel is controlled by the PIM400 it is linked with. The RF channel in use may be changed on the PIM400 through the Schlage Utility Software (SUS). Follow these steps to change the RF channel on the WPR400. 1. Start communication between the PIM400 and the SUS by logging in to the SUS application. 2.
WPR400 Wireless Portable Reader User Guide RESET TO FACTORY DEFAULTS ! All information in the WPR400 will be deleted and reset to factory defaults! Level 1 Factory Default Reset Level 1 factory default reset will delete all Lock Settings as found in the “Edit” tab on the “Lock Properties” screen on the SUS. Edit Tab 1. Remove the WPR400 cover. 2. Press and hold Schlage button until two (2) beeps sound (10 seconds). Inside Push Button 3. Release the Schlage button. 4.
WPR400 Wireless Portable Reader User Guide TEST MODE ! Disconnect the battery from the WPR400 while configuring this mode. (See Steps 1 and 2 at “Install or Replace Batteries” on page 13.) If the Wireless Portable Reader was ordered as WPR400 x DT, the unit is shipped in Test mode. A credential reader is not required to operate the WPR400 in Test mode. The PIM400 should be in Link mode prior to operation of the WPR400 in Test mode. (See Set Link Mode on the PIM400 on page 11 for more information.
WPR400 Wireless Portable Reader User Guide Set Link Mode on the PIM400 1. Mount the PIM400-TD2 to the wall (or ceiling) in the exact location and in the same manner that the PIM400-TD2 or PIM400-485 would be located and mounted (mounting hardware not included). 2. Remove the cover from the PIM400-TD2. 3. Connect the bare leads from the power supply to J2 (DC Power) screw terminal on the PIM400-TD2. 4. Connect the power supply to 120 VAC. 5.
WPR400 Wireless Portable Reader User Guide Use the WPR400 in Test Mode Do not attempt a pre-installation test if the WPR400 batteries are low. See Batteries on page 13 for information on charging the batteries. Always locate the WPR400 in the intended mounting position(s) before and during the link process. 1. The WPR400 should be held in place at the exact spot where the WAPM (WPR400, WRI400 or WSM400) will be installed. (Always hold the WPR400 by the handle, not by the housing.
WPR400 Wireless Portable Reader User Guide BATTERIES Charge Batteries Turn off the WPR400 before charging the battery. 1. Open the power jack cover. 2. Plug the battery charger in to the power jack. 3. Connect the battery charger to 120 VAC. Full battery charge will take approximately 4-8 hours. Install or Replace Batteries 1. Remove the WPR400 cover. 2. Disconnect the battery pack. 3. Remove the battery retainer and the old battery pack. 1. 2. 3.
WPR400 Wireless Portable Reader User Guide BATTERIES, Continued 4. Position the new battery pack in the same location as the old battery pack. 5. Carefully pack the battery wires, and reattach the battery retainer. 6. Connect the new battery pack. 7. Reattach the WPR400 cover making sure no wires are pinched. 4. 5. 6. 7. TROUBLESHOOTING For troubleshooting, browse to www.schlage.com/support.
WPR400 Wireless Portable Reader User Guide FCC/IC STATEMENTS The communication module is a 900 MHz transceiver for electronic locks and non-lock devices. The communication module links the access device to the Access Control Management System, with feedback control to the Access Device via a wireless means. The module contains the embedded firmware implementing the radio physical and data layers. The antenna associated with this module is a PCB trace inverted-L with a measured gain of 5.7 dBi.
© 2011 Ingersoll-Rand Company Printed in U.S.A. P516-098 Rev.
