Installation Guide

ManualsBrandsSchlage ManualsDoor Knobs & HardwarePlymouth Keypad Deadbolt in Aged Bronze

*23780000*

23780000

Prepare for Installation

IMPORTANT NOTES

• DO NOT use a power drill for installation!

• Use a screwdriver to remove product from packaging.

• Install and test lock with door open to avoid being locked out.

• Pay special attention to step 1. If lock is installed with

the cam in the wrong position, the lock will not function

properly!

A Check door dimensions.

See consumer.schlage.com/Service-Support for door preparation

instructions if dimensions are different.

2³⁄₄" (70 mm)

2³⁄₈" (60 mm)

Door Edge

2¹⁄₈" (53 mm)

Hole

5¹⁄₂" (140 mm)

Minimum

B Adjust bolt length, if necessary.

Measure the dimension shown. If the measurement is 2C\v” (70 mm),

extend the bolt.

2³⁄₈" (60 mm) 2³⁄₄" (70 mm)

No adjustment needed. Rotate faceplate 180° to extend.

Not Extended Extended

Keypad

Bolt

Baseplate

Screws (2)

Cover

Screws (2)

Latch/Strike

Screws (4)

Strike

Reinforcement

Screws (2)

Reinforcement

Plate

Key

Additional Parts

Optional Bolt

Faceplate

Tools Needed

• Phillips screwdriver

• Tape Measure

• Pencil

Optional

• Flathead Screwdriver

• Wood Block

• Hammer

Model BE365

Keypad Deadbolt

Installation Instructions

Summary of content (8 pages)

PAGE 1
Keypad Deadbolt *23780000* 23780000 Model BE365 Installation Instructions Tools Needed • Phillips screwdriver • Tape Measure • Pencil Optional • Flathead Screwdriver • Wood Block • Hammer Baseplate Baseplate Screws (2) Additional Parts Optional Bolt Faceplate Cover Screws (2) Keypad Cover Strike Reinforcement Screws (2) Bolt Reinforcement Plate Latch/Strike Screws (4) Key B Prepare for Installation IMPORTANT NOTES DO NOT use a power drill for installation! Use a screwdriver to remove product
PAGE 2
C 2 Change faceplate, if necessary. Install bolt. Choose the drawing that matches your door edge. If the hole has no mortise, change to the circular faceplate. Door Edge OR No change necessary. Door Edge Wood Block (Not Included) OR Actual Size CAUTION Bolt must remain retracted throughout installation! Retracted 3 Install Lock 1 Extended Install keypad. Route wire over bolt. Rotate baseplate cam to correct position. CAUTION Slide tailpiece through slot.
PAGE 3
5 8 Install baseplate. Install cover. Slides through same hole as wire. Holds keypad and baseplate together during installation. Actual Size CAUTION Cam MUST be vertical! Review Step 1! 6 Actual Size 9 Install reinforcement plate and strike into door jamb. Door Stop Connect wire and 9V battery. Lock will beep when battery is connected. For maximum security, install reinforcement plate.
PAGE 4
b Test Lock a Extend bolt (lock). Retract bolt (unlock). 1. Find User Code A on the Keypad Locks Programming Guide. 1. Press the Schlage button. 2. Enter User Code A (four digits) into the keypad. 2. Rotate thumbturn towards door edge. Did bolt extend? 3. Rotate thumbturn away from door edge. Did bolt retract? Yes. Lock is installed correctly. No. Lock is not installed correctly. Remove lock and reinstall. Pay close attention to cam position in step 1. Yes. Lock is installed correctly. No.
PAGE 5
Cerrojo con teclado Pêne dormant du clavier numérique Modelo BE365 Modèle BE365 Tornillos de la placa base (2) Vis de la plaque de base (2) Herramientas necesarias • Desatornillador Phillips • Cinta métrica • Lápiz Opcional • Destornillador de cabeza plana • Bloque de Madera • Martillo Piezas adicionales Pièces additionnelles Outils nécessaires • Tournevis cruciforme • Ruban à mesurer • Crayon En option • Tournevis à tête plate • Bloc en bois • Marteau Teclado Clavier Tornillos de refuerzo (2) Vis de r
PAGE 6
C 2 Si es necesario, cambie la placa frontal. Changez la têtière au besoin. Instalar el perno. Installer le verrou. Elija el dibujo que coincida con el borde de su puerta. Si el orificio no tiene mortaja, cambie por la placa frontal circular. Sélectionnez le dessin qui correspond à votre bord de porte. Pour un orifice sans mortaise, optez pour une têtière circulaire. O OU Borde de la puerta Bord de la porte No es necesario realizar cambios. Aucun changement requis.
PAGE 7
5 8 Instalar la placa base. Installer la plaque de base. Instale la cubierta. Installer le couvercle. Se desliza por el mismo orificio que el cable. Mantiene el teclado y la placa base unidos durante la instalación. Elle glisse par le même orifice que le fil. Elle retient ensemble le clavier numérique et la plaque de base au cours de l'installation.
PAGE 8
b Probar la cerradura Escamotez le pêne (déverrouiller). Essayez le verrou a 1. Encuentre el código 1. Repérez le code de usuario A en la d'utilisateur A au Guía de guide de programmation programación de des verrous à cerraduras con teclado. clavier numérique. Extienda el perno (cerradura). Pêne déployé (verrouillage). 1. Presione el botón Schlage. 1. Appuyez sur le bouton Schlage. 2. Gire la perilla hacia el borde de la puerta. Retraiga el perno (desbloquear). 2.