SCHLAGE SENSE™ Smart Deadbolt Installation Instructions Download the Schlage Sense app to get started!
Schlage Sense™ ENGLISH Installation Instructions Package Contents Camelot Style shown throughout guide. Support Plate Backup Key Battery Cover Touchscreen Assembly Alarm Assembly Strike Bolt Reinforcement Plate Set Screw Bolt/Strike Screws (4) Alarm Assembly Screw Support Plate Screws (2) Reinforcement Screws (2) Need Help? For technical documents and videos, visit schlage.com 2 U.S.A.
Let’s get started! Once you have all your tools together, please follow each step carefully and in order. Because this is an electronic lock, the order of steps is very important. If you skip a step, you may have to perform a factory default reset and start over.
1 Download the app. Download the Schlage Sense app from the App Store. Just search for “Schlage Sense” to find the app. Apple HomeKit™ technology provides an easy, secure way to control your home’s lights, doors, thermostats, and more from your iPhone�, iPad�, or iPod touch�. ENGLISH HomeKit requires an iPhone, iPad, or iPod touch with iOS 8.1 or later. 2 Watch the installation video. You can access installation videos in the app! The videos will give you a good overview of the installation process.
Check door/frame dimensions. •• Measure the dimensions shown. If your door dimensions do not match, you will need to change your door preparation. Go to answers. schlage.com for drilling instructions. Toll-Free Calling From: U.S.A.: (888) 805-9837 Canada: (800) 997-4734 Mexico: 018005067866 »» »» If your door is thicker than 1C\v”, you will need a thick door kit. Please call Customer Service: Mark your crossbore and backset measurements on this page. You will need these measurements for installation.
7 Install bolt and strike. 7a Adjust bolt length, if necessary. •• If the backset (see step 5 on page 5) of your door was 2C\,” (60 mm), you do not need to do anything. Proceed to step step 7b. •• If the backset (see step 5 on page 5) of your door was 2C\v” (70 mm), you need to adjust your bolt. Twist the faceplate until the button pops into the 2C\v” space. ENGLISH Twist the faceplate. Make sure the button pops into place. 7b »» Change the faceplate, if necessary.
c Install the bolt into the door. Choose the picture below that matches your door. Figure B: No Mortise FIgure A: Mortise Make sure the word TOP faces up when installing the bolt. ENGLISH OR Actual Size (2) 7d Use a block of wood and a hammer (not included) to tap the bolt into place. You don’t need to use the screws. Install the strike into the frame. Install all the parts shown for maximum security.
7e Test bolt alignment. 1. Close the door. 2. Insert a flathead screwdriver into the slot in the bolt, as shown. 3. Rotate the screwdriver toward the door edge to extend the bolt into the hole in the frame. This operation should be smooth. You should be able to rotate the screwdriver 90˚, fully extending the bolt. 4. If the operation was not smooth, or if the bolt did not fully extend, adjust your frame and/or door preparation. Go to answers.schlage.
8b Install the Support Plate on the inside of the door. »» Make sure the Touchscreen and Support Plate are straight on the door before tightening the screws. Tighten screws fully to prevent the lock from moving over time. P TO Hold the Touchscreen on the outside of the door while you tighten the screws. P TO ENGLISH Make sure the indented circle is facing the door. Route the cable through the slot. Actual Size (2) 9 Install the Alarm Assembly. 9a Remove the battery cover from the Alarm Assembly.
9b Connect the cable to the Alarm Assembly. »» ENGLISH Locate the screws in step 9d before beginning this step so they will be handy when you need them. The connector fits only one way. Match the dot on the connector with the dot on the circuit board. 9c Install the Alarm Assembly. 1. Align the tab with the notch as shown. 2. Route the cable into the channel. 3. Then slide the Alarm Assembly toward the door. Route the cable into the channel to avoid crimping the cable.
9d Secure the Alarm Assembly to the Support Plate. Install the lower screw first. Actual Size 8-32 x 1Z\,” 8-32 x .187 UP FHMS ENGLISH Actual Size NOTE Please do not rotate the thumbturn at this time. It may not rotate easily. Setup will be performed after installation is complete. 10 Install the Batteries. 10a Install the batteries into the battery tray. 1. Unsnap the connector. ELECTROSTATIC DISCHARGE 2. Remove the battery tray. WARNING! 3. Install four high-quality alkaline AA batteries.
10b Install the battery cover. Speaker Hole ENGLISH DO NOT install screw! 11 Set up the Lock. 1. Open the door if it is not already open. 2. Press the Outside Schlage Button. 3. Enter one of the Default Access codes into the lock (see label shown in step 6 on page 5). 4. The lock will perform a setup routine. Wait until the bolt stops moving before continuing. »» If the Touchscreen did not light up during this step, you may have a power problem.
12b Extend the bolt (lock) using the Touchscreen. 1. Unlock the door using the thumbturn if you have not already. 2. Take the key and the Default Access codes with you! Go outside and close the door. 3. Press the Outside Schlage Button. 4. The bolt should extend. Did the bolt extend (is the door locked)? NO YES ENGLISH You need to adjust your door/frame. Go to answers.schlage.com for adjustment instructions. Did the bolt take two tries to extend? Each try sounds like two cycles.
Spacer Removal (Option for small crossbores only) ONLY if your door has less than a 2Z\,” (54 mm) crossbore, remove the spacer as shown. ENGLISH Less than 2Z\," (54 mm) Crossbore 1. Remove screw. 14 2. Rotate and remove spacer. 3. Replace screw.
13 Continue to the User Guide. Your lock is installed and functional. Continue to the User Guide for complete information about how to configure and operate the lock and alarm. ENGLISH Questions about your new Schlage Sense™ Smart Deadbolt? Please don’t return it to the store! Let us help you first! Apple, iPhone, iPad, iPad Air, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. HomeKit is a trademark of Apple Inc.
If you have questions about any part of installation or programming, don’t return your Schlage Sense™ to the store. Our Schlage Customer Service representatives are ready to help. Toll-free: 888-805-9837 answers.schlage.com Si tiene dudas acerca de cualquier parte de la instalación o programación, no devuelva su Schlage Sense a la tienda. Nuestros representantes del Departamento de Servicio de Asistencia al Cliente de Schlage están listos para ayudarlo.
